Satellite C670D-109 - installation of recovery after replacing HARD drive image

Hello

I have a problem to restore my laptop.
My hard drive is not working, I do not have the recovery disks, but I managed to save the HDD Recovery folder in a partition of DATA.

Once installed the new hard drive, it is possible to recover my original without the cd, but with a pen drive usb installation?

> Once installed the new hard drive, it is possible to recover my original without the cd, but with a pen drive usb installation?
Unfortunately, you will not be able to start the recovery image installation. The data saved on unusable USB on this path. It must be the startup created by Toshiba recovery disc creator device
You can only install recovery image using the recovery disk.

If you n t have it you can order a new one.

Tags: Toshiba

Similar Questions

  • A satellite crashes during installation of XP after replacing HARD drive

    Hello

    I'm trying to install a new hard drive, I boot from a CD of XP.
    Everything goes well until the moment when the system reads "Windows starts now" and then my laptop crashes.

    What I am doing wrong?

    Hello

    First question; What model of laptop do you have exactly?
    Second question; New HARD drive is recognized in the BIOS?

    If you have a series of laptop latest then you should check if the SATA in the BIOS mode was changed to compatible.
    You can install the operating system without previous SATA driver installation.

  • Satellite A135: Vista will not start after replacing HARD drive using the recovery disk

    Toshiba Satellite A135-s7403 HARD drive failed, I have replaced the 80 GB with a WD Scorpio blue 250 GB hitachi. When I try to restore with recovery disk came with the laptop, it passes through two discs 1 and 2 and starts with the start-up of windows for the first time and then runs to the greenish with the spinner blue screen please wait... thne black screens for a second or 2 and then back to spinner, please wait and then it appears the box "installation of windows could not configure windows to run on hardware. This computer' only option is to click OK.

    Where to click ok, you get an another msg that says "windows could not complete the installation, install reinstall windows. I tried like 50 times now. Startup Repair indicates the root = failure cause while the installation program is underway. I know that my drive are good, as I adjusted used then about a month when I upgraded the memory because the original memory 512 MB was not enough o well running vista.

    Hello
    To be honest I n don't know what the problem is there but can you get the original installation disc of Microsoft and try to install the OS, just to see if the OS installation will complete successfully?

  • Satellite L300 - cannot install Microsoft updates after replacing HARD drive

    I am repairing a Satellite L300, which had a dead HARD drive. I replaced death 160 GB of HDD with a 500 GB WD, then used the recovery disks to install Windows Vista SP1 at the exit of the State of the box.

    Now, Windows update does not work, won't install autonomous not of Vista SP2 I downloaded, MS Security Essentials moved there also.
    Then I borrowed a 160 GB of work and went through the same process and everything works fine.

    To make it work with a 160 GB HARD drive, but not a 500 GB HARD drive. Why?

    > ... Standalone Vista SP2 I downloaded will not be installed
    Usually after installing recovery image, you have just to connect laptop to internet and after a short period of time, you will get messages about available Windows updates. Just install the offered updates process automatic Waterer and install important updates only.

    Let the system to install all the updates and don t force the installation of some own downloaded stuff.
    Last month I've updated HARD drive (320 GB I think) and installed Win7 on friends L300 and I didn't noticed any problem here.

  • Satellite L300D-242 - cannot install Vista after replacing HARD drive

    Hi wonder if anyone can help mei have a L300D_242 toshiba satellite that broke down and I bought a new hard drive for it because the original was not good.

    I tried to install a Vista premium 32 bit on the new hard drive, but it does not install until the 4th stage and then stops or hangs until he finishes.

    Does anyone know how to install a new hard drive and windows on this laptop?

    Thank you

    Hello

    What Vista did you use? TOSHIBA recovery disk or a disk of Microsoft Vista?
    Format you the new HARD disk before starting the installation of Vista?

    It is possible that the new HARD drive is not good and therefore the system can not be installed properly
    You can check the drive HARD using a tool called Drive Fitness Test download this as its a freeware program and test your HARD drive.

  • Satellite Pro A10 (PSA15E) - no card after replacing HARD drive wireless network

    Hello

    just a spare hard drive was fitted by an expert, all drivers and update of the BIOS installed on the site of Toshiba, but my wireless network card does not work.
    When I try to connect via a router it says that the card is disconnected?

    I went into Device Manager and of what follows is listed under devices Details ld:
    PCI\VEN_10B7 & DEV_6001 & SUBSYS_600110B7 & REV_01\5 & 36 D 029F7 & 0058F0

    Can someone please tell me which card is installed and where / how do get me to it.
    I don't understand how it can be unplugged?

    I use a 3com officeconnect wireless 11g PC Card which works fine until the hard drive failed.

    Help, please... I am due to go to the hospital Monday and I wish I could take it with me.

    Thank you

    Hello

    Sorry if I write this too late. :(

    He's old enough for laptop and I don't know with certainty what is the card inside, but all notebooks with wireless network inside card have a small stick of Wi - Fi at the bottom with number of WLAN card. Using this number in Google, you can identify the card.

    Anyway, there is not a lot of possibilities because on the Toshiba support page there are two WLAN drivers listed for your model of laptop. Try to install both of them. One of them must be good.

    Good luck!

  • Satellite Pro 2100: How do I reinstall the OS after replacing HARD drive

    I have a Toshiba SP2100 and I want to replace the hard drive, but I don't have any recovery CD
    So, how can I put the o/s back on?

    Try to connect the external HARD drive to the computer via the USB port and try to copy all content from the internal HARD disk external HARD drive. Then you could try to insert the external HARD drive in the laptop.
    But I've never tried this procedure and don t know if it will work.

    But usually after replacing HARD drive you should boot from the Boot CD as recovery CD or the original CD of Microsoft Windows.
    After the installation of clean Windows OS, you can visit the Toshiba drivers and you can download and install the drivers of Toshiba and utilities.

  • Satellite 1410 714 extremely slow after replacing HARD drive

    Hello

    I have a Satellite 1410-714 which has had a hard drive failure. I replaced the drive, but now the computer is extremely slow. Windows has been reinstalled, it was really slow too much and now it takes minutes for windows to start.

    I suspect that something might have broken on the motherboard and the hard disk. I checked mobo replacement parts, but have not found anything for-714, so a 1410 mobo compatible? This model has a processor celeron 1.8.

    Thanks for help.

    Hannu

    Hello

    I can t think the motherboard is broken after replacing HARD drive.
    I suggest updating the BIOS first. Maybe your old BIOS have a few problems with the most recent HARD drive.
    Please check site driver Toshiba for the latest version of BIOS.

    Have you used any anties Virus applications?

  • HP Pavilion 17: mouse pad does not work after replacing hard drive

    Hello

    After replacing hard drive and installing windows 8.1, I can't use my mouse pad.

    I installed the Synaptics driver but it didn't help.

    How can I check that mousepad device is not damaged when replacing the hard drive and which also can I try to fix the mouse pad?

    USB mouse works fine.

    See you soon

    The only way to be sure is to open it up and see if the touchpad cable was disconnected during the upgrade of the hard drive. That's my bet. Easy to forget when you're winding. You don't provide complete model number, but many of the recent models Pavilion 17 require removal of the cover together to get hard disk that requires disconnection of the touchpad cable.

  • After replacing hard drive and reinstall Windows, DVD Player cannot play a Blu - ray disc.

    Original title: dvd player

    recently replaced HDD and reintegrated windows 7.  Now my dvd player cannot play a bluray disc.  Any ideas how to solve this problem?

    Duplicate the content of the thread:

    After replacing hard drive and reinstall Windows, DVD Player cannot play a Blu - ray disc

    My hard drive recently broken and we replaced and reinstalled windows7.  Now I'm watching a Bluray DVD and the drive will not read it.  I tried the fix auto and that said they detected a problem but can not fix this.  Any ideas?

    Hello

    You can check these links and try...

    http://support.Microsoft.com/mats/cd_dvd_drive_problems/en-us

    http://support.Microsoft.com/kb/982116

  • Satellite U840 - how do I reinstall Win 7 after replacing HARD drive

    I had a HARD drive error.

    So I formatted the hard drive (after trying for months to get the process to finally finish that)
    Now, I a U840 Satellite with a clean HARD drive and do not have the installation for Windows 7 discs.

    I searched the net and found nothing of use!
    Help, please

    see you soon
    Nick

    Hello

    You need to create the own recovery in the past disc!
    This recovery disk allows you to install the Toshiba image after the HARD drive is dead or has been replaced.

    In case you have not created this disk, it is possible to order this support:
    http://backupmedia.Toshiba.EU/landing.aspx

  • Satellite A50 - message from system disk insert after replacing HARD drive

    Hello

    I have an old A50 and the HARD drive comes with it's very slow and cracking now, so I'm trying to replace it with a new HDD - Hitachi travelstar 7200 RPM of 60 GB, with ATA interface.

    I took the old HDD and put the new, then on A50 and press F12, and then insert the CD recovery and restored (installation) everything on the new HARD drive. Once it's done, I rebooted A50, but what I got is then a black screen with the message "Insert system disk..." Does anyone know what I did wrong? I got tired of it several times, but I got the same results...

    Thank you.

    I think that Akuma is right.

    On FAT32 and Windows 98 should define the active partition, and then it should work.
    Then download a MS-DOS boot disk and burn it to a CD as Akuma has suggested. I tried it and it works :)
    It is quite easy with Nero.

    Good luck!

  • Installation clean victory 8 - recovery on damaged HARD Drive Image

    Hi all

    I was doing a few BSOD lately, after some research, it appeared due to a missing driver and damaged a windows configuration.

    It's an Alienware 17

    Intel Core i7-4900MQ CPU @ 2.80GHz

    Type
    Description
    CD-ROM/DVD-ROM readers
    HL-DT-ST DVDRWBD CA40N
    Disc players
    WDC WD7500BPKT-
    WDC WD7500BPKT-22PK4T0
    Graphics cards
    GPU Intel(r) HD 4600
    NVIDIA GeForce GTX 780M
    IDE ATA/ATAPI controllers
    Keyboards, mice & pointing devices
    Synaptics TouchPad SMBus
    HID-muis
    Razer Naga
    Monitors
    Algemeen PnP-sit
    Standaardbeeldscherm
    Sound Devices
    High definition Audio-expensive
    Bluetooth audio
    Razer Kraken 7.1
    Realtek High Definition Audio
    USB controllers
    Intel (r) 8 series/C220 Series USB EHCI #2 - 8C2D
    Intel (r) 8 series/C220 Series USB EHCI #1-8C 26
    Intel (r) USB 3.0 eXtensible Host Controller - 0100 (Microsoft)

    mid-2013

    So I thought to do a factory restore and reinstall windows, but because this machine has been shipped in mid-2013, it has been bundled with windows 8 and 8.1 not. I cannot recover my system with the options of windows using the boot disk, I received when purchasing.

    Or reinstall the system via the DVD starts works. Installation could not see my hard drives correctly or missing drivers.

    Now, I did a system restore (Yes surprisingly has started up normally this morning) but I am always a little scared and would have preferred a clean install.

    Decided to buy Alienrespawn Premium to try to restore my original recovery Image and reinstall the original windows 8 from scratch. But during the selection of these options, I get the message that the image is missing or incomplete. When I try to select another HARD drive he asks to insert a disk external HARD at least 100 GB on this subject. Is there an internal HDD option and select put this system up? I've got 2 750 GB SATA HARD drive and the other has been completely formatted for backup reasons...

    Could someone please help me and tell me what to do in this case?

    A clean install would be the best way to go, but I tried everything I found on google in communities and to but still do not get them to factory reset my PC...

    Thanks in advance

    Boempatat

    My warranty has expired in order to request a backup CD is not going to work I'm afraid...

    I have a cd provided dell with the laptop, but as said my laptop has been delivered with WIN8 not earned 8.1

    I can't do a clean install, as described in the article, because it tells me to load the required drivers and there is a missing part so that my cd is in the laptop...

    I need to find a way to recover the original recovery on the HARD drive in order to reinstall the complete system with the factory settings...

    Please tell me how to do this.

    It looks like your BIOS may be on the RAID.

    The value of the BIOS:
     
    SATA Mode = AHCI Mode
     
    = UEFI boot mode

    DVD Win7, Win-8-DVD, or a USB flash drive should now start. Use the one-time-starting F12 menu.

  • Error "Windows Update cannot currently check for updates, because the service is not running." You may have to restart your computer. "after replacing hard drive

    I've upgraded to a replacement hard drive, but Windows Update won't work now. Everything else seems OK.

    The error is: "Windows Update cannot currently check for updates, because the service is not running." You may have to restart your computer.

    I restarted the computer a couple of times and in respect of the Services runs it the Windows Update service.

    Operating system is Vista 64 bit.

    Original title: Windows Update

    I've upgraded to a replacement hard drive, but Windows Update won't work now. Everything else seems OK.

    The error is: "Windows Update cannot currently check for updates, because the service is not running." You may have to restart your computer.

    I restarted the computer a couple of times and in respect of the Services runs it the Windows Update service.

    Operating system is Vista 64 bit.

    After the upgrade to the bigger hard disk, I found that the technology Intel Rapid Storage Technology driver should be updated. Once this is done Windows update ran properly. Microsoft Fixit did not help in this circumstance.

  • Satellite C650, media recovery fails after replacing HARD drive

    I have a 3 years C650, and the HARD drive has failed. I got a replacement drive and sorts to recover from the recovery media disks that I created and although he claimed to have re - partition the drive and reinstalled windows, windows startup fails when tried to configure the devices "could not configure windows to run on this hardware.

    After this error, the boot sequence goes into an endless loop, asking to start the installation procedure.

    Thinking that my records may have been corrupted, I ordered a set of Toshiba recovery disks. Once again, these go through the recovery process and still once, Windows startup does not exactly in the same place.

    A little annoying to have spent £30 for nothing.

    I have a picture of Windows system on my external HARD drive, but I can't get the machine to a point where it will actually start so I can recover from that.

    Any suggestions on how to proceed is welcome!

    Thank you
    Martin

    Hello

    Of course, this isn't a problem of recovery disk.
    I guess there is a problem with the HARD drive but I n t think that the HARD drive has failed I think there is a problem of setting

    First, you should go to BIOS and check if the SATA set to AHCI.
    Then you should also format the HARD drive again.

    I recommend to use the freeware tool called GParted. You could create a live USB stick bootable flash memory which will allow you to start the unit and start GParted tool.
    Format the HARD drive, and then create a partition.

    After that, take the recovery disk and start the recovery procedure.
    Good luck

Maybe you are looking for

  • Download the printer drivers on ipad

    Hi, I have an ipad that works on Safari and I have drivers for the photosmart e 5520 problems downloadind all in one set.

  • HP software detects the printer, but then "the printer could not be installed on the network.

    I tried looking for a similar problem, but have had no success yet.  I doubt I'm the first to this problem! The computer is XP SP3, is printer Deskjet 3050 has, and it's a WiFi WPA - PSK. The printer confirms that it is connected to WiFi. When I run

  • LabVIEW DLL called from C

    I would like to create a DLL in LabVIEW which can be called from a C program. The purpose of the DLL is to display a dialog box along side a C program user interface and view a picture is updated continuously in the program. The LabVIEW DLL would be

  • Unavailable Windows contacts

    I recently reset Windows Mail from a backup; Although the Windows Contacts file is still OK, I can't access the file via the 'beneficiaries' field when you write an email. Please notify.

  • Identify the loop of the Internet - an internet connection

    Hello My PC (Windows 7 64 bit) does not connect to the internet all of a sudden. She stays in a loop "login" on the wired connection. WiFi connects but in the same way, will not allow internet access. My ipconfig all reads: Windows IP configuration N