Satellite C870D-10 t won't start - flashing cursor

Hello

I'm really stuck here,
A few days ago my laptop (Satellite C870D-10 t) began to have problems with its slowness and browsers started to freeze.
Of control of virus then did a chkdisk and then the real problems started.

When I tried to start (recommended), or reboot I get the message starting windows normally when choosing repair startup would start loading windows files then stop after the windows logo and go to a black screen with cursor.
Security modes do not work either.

I must of retries to more than 50 times until I then opted for drive recovery HARD and restore to the factory settings. After I did it I had a similar thing happenend.

Windows first loading of files, windows logo, Assistant recovery: choose language, then the screen with the white cursor black... sometimes I got error F3-F000-0001
Only on one occasion did he go a bit more far but left after the same error message I think.
Restarting the disc also has not worked since the first time I did the HARD drive recovery.

ANY HELP is very appreciated

welcome them

Hello

I think that the HARD drive is faulty.
The cursor blinking in the upper left corner is a typical sign of a malfunction of the HARD drive.
I recommend you to check the new HARD drive.

Also a problem of RAM may be the reason for these problems, but I recommend check (replace) the HARD drive first.

Tags: Toshiba

Similar Questions

  • Satellite L635-S3030 won't start - flashing cursor

    My laptop won't boot! When I turn it on, the Toshiba logo comes then it goes to a black screen with a small white cursor that turns into a smaller white cursor. It won't do anything else!

    It just flashes and when I press the power button it turns off. I need help!

    How can I get my computer to work?

    Hello

    I think you're talking about the cursor blinking in the upper left corner. Right?
    Well, I can tell you that the blinking cursor is a typical sign of a malfunction of the HARD drive.
    I think that your HARD drive is dead, and perhaps that is the reason why the laptop can not boot from the HARD drive.

    Solution:
    Replace the HARD drive and install the operating system using the recovery disk.

    Guarantee is valid? In this case get in touch with Toshiba Asp in your country to get this replaced.

  • Satellite Pro A300 PSAGDA won't start at all after flash Bios 1.90

    I have an A300 PSAGDA-01Y00R.

    I tried to Flash the bios to version 1.90. He started the process, and when I came back an hour later the cell phone was off.

    When you turn it on, it has nothing now. I tried removing the battery and running on sector only.
    Works for keyboard (as in light) and power works, but there is absolutely no action on the screen.

    Is there anything I can try?

    Hello

    Try this;
    Remove the battery, disconnect the adapter and wait 1 hour.
    Then connect both devices and try to turn on the unit.

    If this will not help, then you will need to contact a local ASP.
    It seems that something was wrong during the BIOS update process and therefore, the laptop can not initialize correctly.

    I put t see another solution for your problem

  • Desktop won't start. flashing green light

    I have a 1318NX Compaq Presario SR which will not start!  There is a green light flashing on the back of the power supply; which is normally green 110V AC is plugged into it.  I tried the trick of the Start button while not plugging the power cord... no help.  I also opened the case and carefully got rid of any power cord of all internal devices... the light turns green only when I pull the main power of the motherboard!

    I need to replace the motherboard?  Troubleshooting on hp.com site would indicate that the power supply is OK if the light is solid green.

    Thanks for your suggestions,

    Lou

    My wife's computer had the same problem several times. A solution I found that worked before was to unplug the power cable from motherboard and the power supply cable to the back of the PC and then connect the power cable and plug the motherboard power cable while holding down the power button. Scary, to say the least, but it worked, until one day I accidentally spilled the bad circuit breaker and then spend two hours trying the same solution with no luck and the Google search again. And here's what I found. It is the simpler solution even more cruel. It is simple and noninvasive and no matter how tech savvy you are. Take a blow dryer and turn it on to blow air at the rear of the power supply for a few minutes. When you see the light turn green, you're ready. It's worked for me after that it worked for a hundred others, maybe more. A look at the testimonials on this site: http://talk19.wordpress.com/2008/01/13/hp-m7088d-power-supply-led-blinks-green/. It's a shame that nothing like that appears on any site of HP. So don't waste your money on a new MoBo or PSU. All you need is dry hair of your wife.

  • Satellite A60 - recovery disc won't start plus-disque no bootable error

    Hello

    I set the boot sequence to boot from the cd, but the message reads: no bootable disk.

    I tried to open it with ghost, but looking for a password.

    Toshiba Satellite A60.

    Hello

    First you will not be able to extract the ghost image file because it s set as you could see.

    I put t know why you can't boot from the recovery CD Toshiba. But reasons could be:
    -The CD is defective (zero, not more readable)
    -You used a bad CD
    -The CD/DVD drive can not handle this CD because of the lens of the laser drive old and faulty.

    Then you should check first if you can start on other Microsoft Windows CD to see if the CD/DVD drive is ok.
    If it is ok, then there is a problem with your CD!

  • Satellite C650 - 15 X won't start Win 7 - where to get the recovery?

    Hello

    I am in the United States with a laptop computer crashed after an infection Trojan (PUP-...). Removed to Malwarebytes, but the computer won't open windows, even in safe mode. All attempts to make the Toshiba repair program that fails every time. I'm trying to get a disc of recovery for this machine. On the Toshiba-USA phone said to contact Toshiba-France, which in turn says sorry, online only. On their website, I can't find the right page, even though I am French.

    Does anyone know the address of the page in order for a Toshiba Satellite C650 - 15 X recovery disk? (of course, I have the serial number)

    Thank you for your help,
    Christian to feel really stupid

    Hello

    Restore disks for European Toshiba, laptop models can be ordered here:
    http://backupmedia.Toshiba.EU/landing.aspx

    But have you tried to recover the laptop using the recovery of HARD drive?
    [How to recover a Toshiba notebook with the HDD recovery procedure | http://aps2.toshiba-tro.de/kb0/HTD1303440001R01.htm]

  • Satellite L350 - no lights, won't start

    My satellite L350 does not start. He's been completely dead no lights nothing. He's going to the charger and the battery has power.

    Any help apreciated...

    Hey Buddy,

    I think I found something that might be interesting for you:
    [What steps must be followed if your Toshiba laptop does not start? | http://forums.computers.toshiba-europe.com/forums/ann.jspa?annID=21]

  • Re: Satellite A100-803 PSAANE won't start no-glued on the Bios POST

    Hello

    I have the following problem with a laptop computer to a customer.
    After having turned it on, it has the logo Toshiba rest on and everything is hanging there.

    After pressing ESC, there is a message: "NO TPN or TPN has problem.
    So, I think that the Bios broke down. How, I don't know.

    Trying to enter in the setup by pressing F2 system displays "enter the configuration" but nothing happens. He stayus on this screen.
    Is there a solution I can try to recover the Bios damaged from a USB or a USB floppy drive.

    I checked the Toshiba support site, there is a Bios Update, but it is a program that should be started in Windows so I can't use it.
    Anyone have an idea how I can recover the corrupted Bios.
    I have already removed the battery and the power and hold the powerbutton to for +-30 sec, but that does not solve the problem.

    Thanks for help out me.

    Best regards

    Cauberghe Didier
    Dealer.

    Hello

    You are right. There are, it's no BIOS which can be not started BOF on floppy or USB key.
    You must update the BISO running windows OS.
    But according to your message, it is not possible.

    If you have no alternative but to contact the maintainer authorized Toshiba in your country.
    Guys should be able to help you. I presume that the technicians have access to the traditional BIOS version that can be updated using a disk.

    Good

  • Satellite C660D froze and won't start - Windows could not start

    OK, enough of the more dense person you will ever likely to meet when it comes to things like that. but will try my best to explain.

    There are a few days that my laptop has frozen on me on me having to turn it off and start it again by the power button. When I started again the message below appears.

    WINDOWS ERROR RECOVERY
    Windows could not start. A recent hardware or software change might be the cause.
    If windows files have been damaged or misconfigured in, Startup Repair can help diagnose the problem, if the power was interrupted during startup upward, choose start windows normally.

    -Launch start repair (recommended)
    -Start windows normally

    When I press launch Start up repair that it goes to a screen with a big cursor (that you can move) but nothing happens.
    When I pressed the start windows normally put it went through the windows logo while starting but then stops at this point.

    My question is, is - this easy to fix & if not where is the best place to consider to get fixed. Said I was dense enough: p

    Thanks for looking

    Dean

    > My question is, is - this easy to fix & if not where is the best place to consider to get fixed. Said I was pretty dense

    I think its easy to correct, but you'd need a Toshiba recovery disc.
    Have you created one in the past?

    If not, try to start the HARD drive recovery: turn on the device, press F8. Now choose fix my computer.
    Now new window should open, and here you must select Toshiba HDD recovery option. This would create the laptop back to factory settings.

    In case this isn't possible, you will need to boot from a recovery disk to reinstall the system.

  • Satellite L450D-11V - Windows won't start not

    I'm unable to start Windows. I pressed f8 and tried all options. I tried the Startup Repair which just goes to a black screen. I tried the product recovery disc, and I just went to a black screen with an arrow. I have my own recovery disc I made last month, that does not work either.

    Any help would be appreciated.

    Jude

    (The trouble started after an error I think it was a problem with wmv.dll?) I saw the message briefly so my memory is perhaps faulty)

    Enter the Bios (f2 at startup) to check if the hard drive is recognized

  • 13 stream: Stream HP 13 (13-c010nr) won't start - flashing caps LED twice

    Laptop boot more.  Was working fine before that we have a significant voltage drop/blackout.

    Shift caps lock flashes two times, and then repeats.  Black screen.

    Not useful support Web site.  Guard sends me the General information on blink codes, which may mean that my BIOS has been corrupted.  I tried Windows-key + B + Power to reset the BIOS, but not sure it will work on this model.  Just did the same thing.  Never made up a BIOS screen with option to retrieve internal drive.

    I could go through the hassle of building a USB from BIOS drive, but the site doesn't tell me if a 13 Stream supports the functionality of booting from a USB BIOS using Windows-key + B + Power key.

    Any suggestions would be greatly appreciated.

    Discovered that YES, the 13 HP FACT flow support reload the BIOS from a USB key, even if it will not recharge off the internal memory drive.  Problem solved.

  • Satellite Pro 2100 won't start at all - LED flash

    My SP2100 began to have feeding problems and now won't start at all. The AC adapter green LED is lit, that are relevant lights on the body of the laptop (although the "battery charge" light always orange these days). When I try the switch on, startup begins (in fact succeeded on occasion until this morning), however the battery indicator and the adapter lights are flashing, and everything stops again.

    On the rare occasions when I'll be past this stage, lights blinking, and the system soon shuts down again with a screen message "low battery." Until this morning, he would sometimes settle, the computer remained on, and the lights showed a State of equilibrium as usual.

    Initially I thought that the problem was of course the battery or the AC adapter, but now I'm starting to think that it is with internal PSU of the laptop (although I suspect the battery is probably tour after all this part of loading and unloading).

    Any ideas?

    Hello

    I think you're right. Flashing LEDS are a sign that hardware is defective.
    I can't say what exactly is the problem, this should be verified by a technicain.
    On the other side I don't know if it's worth to repair such an old machine.

    Good bye

  • Satellite Pro 6000 won't start or do something

    Hello

    My satellite pro 6000 stopped working all of a sudden.
    Power led, battery, keyboard LED is on, but nothing happens, tried to remove the battery, cd, hd and put them back, nothing seems bad.
    Also tried the back button back in case but no tip was not all good.
    It just won't start at all.

    Any ideas out there?

    Thank you

    [Edited by: moderation of the Forum]

    Do the job of seem´to LEDs ok, or they do a code flashing for you say that it is something wrong?

  • Satellite L30 PSL33E won't start at all - the LED blinks 6 times

    Hello

    My poor mother is quite upset! Its Satellite L30 PSL33E just died.

    It completely off and now won't start at all.
    Orange light flashes six times when you press the power button.
    No hard drive, fan, screen or any other noise / activity.

    She tried without the battery.

    A kind of hardware failure, I guess.

    Any ideas what this blink code means?

    Thanks in advance,
    D.

    I put t know what the code means, but you can read it. short means 0 and 1 long

    In any case, the error code means that a hardware failure has been detected on the motherboard and motherboard replacement could help you?
    Why?

    because what is really hard to fix a motherboard for laptop very s.
    It especially not possible if you n t s have sufficient knowledge, experience, and special tools.

    I think that either you contact the ASP in your country and ask a difficulty or you'll have to buy a new laptop ;(

  • Problems starting with the Satellite C870D - 11 X

    I have a Satellite C870D - 11 X 8.1 Windows running.

    The laptop was running progressively slower, but now when I start it sticks on the screen "Toshiba Leading Innovation". Finally, he moves to a blue screen saying that your computer needs repair "a required device cannot be accessed 0000185 0xc error code. I tried a reset by pressing '0' at the beginning, to the top and I see the process of disk recovery hard screen and press enter for Yes and I get the "Toshiba Leading innovation" screen with please wait. After the circular points are displayed for a few moments, then the screen becomes white.

    Unfortunately, I don't have a recovery disk to try this option. I'm looking at a hard drive failure? I hear a feint clicking of the HD as if hunting for something.

    If I buy a disc is it likely that I will be able to reinstall using this media?
    Thanks a lot for your suggestions.

    At first, I must say that you have made a mistake after that you bought your laptop you didn t create disk recovery or the so-called recovery media with the original version of Windows 8 that you got with your machine.
    I really do not understand why so many people make this mistake and do not create bootable recovery media installation backup image recovery.

    In any case, on this path virtual that is not easy to say what the problem is here and, in my opinion, the better you can do is to back up all your important data and install original recovery image. After doing this, you can test the functionality with the factory settings.

    A few days ago, I found interesting options paper of recovery limited after update to Win8.1 - http://aps2.toshiba-tro.de/kb0/TSB4403L30001R01.htm
    You should try to install the HARD drive recovery original anyway. How is it that you can read on http://aps2.toshiba-tro.de/kb0/TSB2A03ES0000R01.htm or http://aps2.toshiba-tro.de/kb0/HTD1303440001R02.htm (Win8/8.1).
    Order recovery media can be your last step.

    Clicking noise could be sign of drive HARD doesn't work well anymore. Is the warranty for your machine still valid?

Maybe you are looking for