Satellite L10-232: black screen after closing the lid.

Similar Questions

• Satellite L350D - 11K: black screen after downloading the Tempro updates

  Hi Forum,

  yesterday, I admitted Tempro download several updates on my satellite L350D - 11K.
  During the last update, it was an update of the firmware, the system crashed, and it no longer starts.

  After removing the battery, the system starts up, but now it has a black screen and I don't know what to do.
  Pressing any key F doesn't show any results and I have no recovery CD.

  Does anyone have an idea what to do?

  Thxxx in advance

  Hello

  I don't know why it happened, but if the short workaround solution posted by boarder will not help, so I see good opportunities to contact the ASP in your country for assistance.

  > During the last update, it was an update of the firmware, the system crashed, and it no longer starts.
  You're talking about the firmware update
  Maybe it was a BIOS update which failed and so the laptop will not start again
  As already said in this case that only the ASP technician could help you.

• Qosmio G20-127: failure to screen after closing the lid on Vista

  Hello

  I have a Qosmio G20-127 and I recently installed Vista Ultimate (32 bit). I managed to put everything in its place (except the magic buttons, but the drivers are not on yet), but I have a problem that makes me seriously reconsider coming back to XP MCE.

  When I close the lid of my computer, the screen turns off of course, but when I open again, it does not turn, but it stays black. And I can't turn it on again no matter what. I have to turn off the entire computer and it is quite unrealistic.

  Funny is that after a restart for about 20-30 minutes, I can open and close the lid normally, but the same problem occurs after a bit more time to work on the computer.
  The problem persists even though I disabled everything remotely connected to the closing of the cover.

  Does anyone have a solution?

  Hello English

  Try you update the BIOS on the VISTA OS?

  I can imagine you will always find something new and unusual, but please note that Vista is not supported by the OS for Qosmio G20 (Vista drivers are not available on the Toshiba download page) and you can expect that from time to time, you will discover new disturbing behavior.

  I recommend you to install and configure Vista as described in the topic of s Francisco, configure OS for your needs, and be happy if you use Vista without any serious problems. In my opinion, for OS installation and configuration software Qosmio is Toshiba laptop more complicated template, and you will never be able to configure it as a supported and preinstalled WXP MCE. Commands supported are tested and bugs are fixed, but not with Vista on Qosmio G20.

  Sorry my friend. Sounds stupid, but maybe that's just the truth. By the way: I like Qosmio G20. Maybe I'll buy one if the price is Ok.

  Good bye

• Black screen after opening the lid - Pavilion g6

  Hello, I need help. I bought my laptop a few days ago and installed Windows 8.1.  When I closed my lid and opened after a while the screen remained black, so I had to force close button and restart. I tried to change the power plan settings to "Choose the closure of the hood", and it always ends the same way "Black screen", does nothing. This is a brand new laptop and it is that wories me. It must be a software problem, I hope that you guys could understand.

  Thank you Marko

  Finally, I found a solution.

  I did Update my Windows and everything works fine from that point.

• Satellite L300-1FS - Wireless reconnect after closing the lid

  Hello

  My 2 month old son Toshiba laptop works very well in many ways, but an annoying problem, is that if we close the lid when you open it again it doesn't re connect to our router. If I click on the network connection, it just says: there is no everything!

  Sometimes the switching market re wireless switch will connect there, but more often than not, it's a reboot, which is annoying.

  Proves that the wireless card works but it would be nice to not have him harass me every time it does not connect.

  All ideas welcome.

  Hello

  First a question: what exactly happens if you close the lid?
  This laptop stops, or goes to stand-by or extended sleep?

  However, in your case, I would try to update the driver WLAN and the BIOS. Check the Toshiba website for updates:
  http://EU.computers.Toshiba-Europe.com > support & downloads > download drivers

  It would be interesting to know what operating system you have and if you are running the factory settings or you have installed another OS?

  A friend told Satellite L300 and he is very satisfied and can t notice any problem. :)

• Satellite A200-13R - black screen after cleaning the fan

  Model name: Satellite A200-13R
  Model no: PSAE0E-011014GE

  I clean the fan, and I put new thermal paste to the processor. After finishing this job button press / the laptop works but the screen is black. The laptop shows that read the hard drive and the processor works well. I'm trying to remove the battery, disconnect the power, hold the button works / power off for 60 seconds, turn on computer with power plug, then stop, add the battery and restart * but the screen is always black *. I try to press Fn + F5 reboot screen * but again is black *.

  Any solution please?

  Thank you

  Nick

  You have disconnected the display while you cleaned up the laptop?
  Are you sure that the display is connected correctly?
  Check the cable?

  > The laptop shows that read the hard drive and the processor works well.
  How do you know that? Flashing LED HDD?
  You know, it's not easy to say what may be the problem.

  You can also try testing with external monitor.

• I am expierencing problems with my isight Camera on my MacBook Pro. Suddenly the video camera does not start (no green light on) FT or Photo Booth. The screen is black, if I restart computer it works but after closing the lid, it stops. V10.11.3

  I have problems with my view i camera on my Mac Book Pro. Suddenly the video camera does not work (no green light on) FT or Photo Booth. The screen is black, if I restart it, it works but after closing the lid it stops and I have to restart the computer.  I use V10.11.3. An idea about what is happening

  Hello mpm068,

  Thank you for using communities of Apple Support.

  Since your iSight webcam works up to the time that your Mac goes to sleep, I would like you to start please help desk trying to replicate this problem then to reboot in safe mode:

  1. Choose the Apple menu > shut down.

  2. After your Mac stops, wait 10 seconds, then press the power button.

  3. As soon as you hear the startup tone, hold down the SHIFT key.

     You must press the SHIFT key as soon as possible once you hear the startup tone, but not before.

  4. Release the SHIFT key when you see the gray Apple logo and progress indicator.

  To exit safe mode, restart your Mac, but no press during the startup.

  OS X El Capitan: start in safe mode

  Take care.

• PAVILION 15: BLACK SCREEN WHEN OPENING THE LID ON WAKE UP

  THE LAP TOP SHOWS A BLACK SCREEN WHEN OPENING THE LID.

  THE SCREEN WORKS WELL WHEN PUT ON, BUT ON CLOSING THE LID FOR A WHILE AND RE OPENING STARTING THE ENGINE AND THE LIGHTS FLASH BUT THE SCREEN IS BLACK.

  TO RETRIEVE THE SCREEN POWER BUTTON MUST BE PUSHED AND WHEN FLASHING JUST AGAIN PUSHED THE SCREEN THEN WAKES UP.

  THIS FIRST STARTED WINDOWS 10 CHARGE BUT WHE I GO BACK TO THE FACTORY SETTINGS AND WHICH IS 8.1

  I TRIED TO REMOVE THE BATTERY TO RESET AND REMOVE AND REPLACE MEMORY CARDS AS SUGGESTED BY SOME SITES I RELOADED ALSO BIOS AND I STILL HAVE THE PROBLEM.

  I WOULD BE VERY GREATFUL FOR ANY HELP.

  Hi @lily-springer,.

  Thank you for your update.

  I am pleased that now when you close the lid, it does nothing.

  You don't have the possibility to contact the HP support for assistance. They can access your system remotely to help overcome the difficulties.

  Contact HP to Contact HP Support assistance

  Good luck!

• Tecra M7: Tablet does not work after closing the lid

  Someone had problems with the Tablet does not work after closing the lid on a Tecra M7? BIOS is 3.20

  Does not happen on hibernate or sleep.
  I have the set cover to do nothing on close.

  Hello

  What do you with Tablet does not work after closing the lid?
  Is - what the laptop freezes or what? What happens exactly?

  Closing the parameters adjustable lid to Hibernate or standby mode or no action.
  These settings can be defined in configuration power saver actions.

  If you have some problems with some Toshiba applications installed, I recommend you to reinstall the program and TOSHIBA common Modules that doesn t work properly!

  Best regards

• Restart the problem after closing the lid of the laptop for a few minutes

  I use Windows 7 Home Premium on my Asus A53S. I have reboot issues a few minutes after closing the computer laptop lid eventhough I put what to do after closing the lid to "do nothing" for both on battery and the plug. And it will keep restarting over and over again. Rest

  Hi DennisHii,

  You did changes to the computer before the show?

  Method 1
  I suggest you perform the clean boot and check if the problem persists.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
  http://support.Microsoft.com/kb/929135
  Note: Follow step 3 of section of boot KB929135 to reset the computer in normal mode.

  Method 2
  I suggest you try the steps from the following link:

  Windows 7 is not going to sleep
  http://support.Microsoft.com/kb/976877

  Hope this information is helpful and let us know if you need more assistance. We will be happy to help.

• Satellite L500 - external screen display after closing the lid?

  Hello
  I use the Satellite L500 - 120 Notebook, and before installing Windows 7, the laptop has a function very uncomfortable, when I applied an external display.
  When I closed the lid of my laptop, Office was shown on my display (with the native resolution of the external display) external, so I had not to
  change anything on the control panel. In Windows 7, Miss me this feature. I already tried to use the Control Panel, but there is no parameters, which fits
  with the previous ones. I can duplicate the screen in order to see my desktop screen on my external screen, but with the resolution of 1366 x 768 laptop.
  If I extend the views, then there is only the background image to the external screen, but this time with the native resolution.

  So my question is, how to conifgure Windows to recognize that I closed the lid, and the screen should be shown on my external screen?
  Or should I install applications Toshiba, that I had before, who visited account this function?

  Thanks for any help!

  Hello

  I m not a Windows 7 user because I want to wait until it will be released official, but I hope that I can help you a bit:

  First of all in power management, you can choose the action that happens if you close the lid (g. e. sleep, close, etc.). This action must be disabled because otherwise the laptop shuts down or something else.

  So I think that you need to install the display driver for your laptop. You can try the Vista driver because most of them are working on Windows 7.
  Then you should be able to define the correct screen resolution for external monitor.

  A working display driver is important to the clone or extends monitors to verify this!

• Satellite Pro U200-> black screen after startup

  Hello

  It happens from time to time when I try to start my PLUA1E Satellite Pro U200-02802QS4, then I get a black screen even from the BIOS.
  What is wrong and how to fix this?

  BTW, I already have this BIOS version: P0044v370.exe installed.

  Hello

  This happens from time to time?
  This means that you can not reproduce this problem?

  Hmm that's not easy to say what the issue might be.
  Maybe the BIOS update will help you at the moment you can find BIOS 3, 7 victory on the European driver Toshiba page.
  If you have a lower BIOS version installed, then I recommend an update.

  It is also possible that this problem is related to some of the material; motherboard, screen, etc.
  In this case the part should be replaced but first of all it of necessary to know what part is affected and I think that the technician of the ASP for this

  What do you think???

• J5B54EA #ABU: help black screen after put the password in

  I turn on my laptop and everything is normal until after I type my password and it is supposed to go to my office instead it goes straight to a black screen, I can not access my Start menu ive had the laptop 4 months on its never had any problems and was working fine an hour ago

  Hello

  Try this and let me know.

  Boot the computer normally and log.

  Black screen, hold down the ctrl and alt keys and press delete.

  Select Task Manager.

  At the bottom left, select details (if it is not already selected).

  Click in the header of column Nsoul to organize the processes in alphabetical order.

  Look for an entry called to run once Wrapper (RunOnce.exe) - If you see it listed, right-click on it and select end task.

  The office is now show?

  If this is the case, download Autoruns on the following link and save it in your downloads folder.

  http://download.sysinternals.com/files/Autoruns.zip

  When you have that, open your download folder, right-click on the folder zipped to Autoruns, select "extract all...". "and in the next window, click Extract.

  A new window will open displaying the extracted content.  The application you must launch is the 2nd in the list (in format autoruns 636ko) but this by right clicking on it and selecting 'Run as administrator' -click 'Yes' to the uac prompt.

  Scroll down the list until you find the entrance to RunOnce (it may well be 2 entries) and Remove the tick (s) in the box next to it.

  Restart computer and see if it boots now on the desktop.

  Kind regards

  DP - K

• Black screen after entering the password to open Windows Vista

  I need help for vista windows Desktop to appear. All I get is the black screen after I get my password

  Aziz I apologize not responding earlier! In fact, I had to do was reboot the pc! I wish I knew exactly what it was that I did!

• Pavilion dm4-black screen after opening the cover of the fashion watch

  Pavilion dm4-3000tx

  Windows 7 (64-bit)

  When I close the lid of the laptop and re - open the screen remains black. the sounds keep playing and if a video is palyed before closing the lid, he also plays with the play/pause button, but there is no graphics on the screen, only a black screen while all runs in the background. I have to restart the machine with the power button then.

  action dafault on the cover is the sleep and re - open the cover and press a button he wakes up, but the screen is still black. problem when I change the dafault action: do nothing

  Hi zineb. I understand that your computer is well problems wake up sleep mode. I found a thread from Microsoft that contains a good amount of troubleshooting for this issue: http://answers.microsoft.com/en-us/windows/forum/windows_7-performance/blankblack-screen-on-wake-up-from-sleep/6fdca378-6279-486e-8e7f-6e90a3f9d42f

  Please inform me of your results when the diagnosis is complete. I'm only here to help!

  Mario