Satellite L300-135 see WLan network but will not connect

Similar Questions

• Windows Vista detects the wireless network but will not connect to it. Two other users in the same office connect without difficulty.

  The title says it all really.

  I was connected and working normally for about an hour this morning, until suddenly the connection has been lost.
  Windows detects the wireless network but will not connect. Two other users in the same office connect without difficulty.
  Help, please.
  Thank you.
  original title: vista detection network but will not connect

  Hi JulianBeach,

  1. you have made no changes to the computer before the broadcast took place?
  2. What is the exact error message you get?
  3 is connected to the domain of the computer?
  4. what happens when you try to connect to the network?

  Try the steps from the following link:
  Windows wireless and wired network connection problems
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Additional information:
  Wireless network card: frequently asked questions
  http://Windows.Microsoft.com/en-us/Windows-Vista/wireless-networking-frequently-asked-questions

• WIFI on my C850 Satellite can detect the network but will not connect

  I just bought a satellite C850 - PSKCCA-02D00M

  The connection to the LAN works fine however the Realtek RTL8723AE without wireless/Bluetooth will not connect to the network. It can can detect them just does not connect. I used the troubleshooting, and he cannot sort.

  All other devices connect very well as Iphones and Kindle

  In the config is doctor says that the adapter is enabled in a domain and in the adapter another status is down.

  I took back to the initial power and installing and unistalling and reinstalling the adapter using the driver on the website.

  Any help is welcome. I don't want to have to take back just for this issue

  See you soon

  Your WLAN is locked? Can you connect WIFI if you delete the WIFI password for two minutes?
  Have you tried to reboot your router?

• Satellite L350-14F find the router but will not connect

  Hello

  I just bought a new laptop Satellite L350-14F, but I can't seem to connect to my connection wireless broadband.
  My roommate's laptop connects fine.

  The mine finds the network, asks for the WEP key but will not let me.

  I am running Windows Vista SP1.

  Can anyone help?

  Hmm. I recommend you to check the settings of the WLan router.
  If the MAC address filtering enabled and that your WLan MAC address was not included in MAC address filtering, then you would not be able to connect to the router.

  It would also be possible that you try to insert an incorrect encryption key

  Therefore, it would be desirable to disable all the security settings on the router and then try to establish the WiFi connection.
  If this would have functions, then you might reactivate the WLan security settings.

  By the way; Check if an update of the Wlan driver could also sometimes there is some compatibility problems between the Wlan router and Wlan card drivers.

• Windows Vista Business ed. reformat - my computer detects the network but will not connect to Internet

  Can someone help me, I can't reformat a laptop compact with a windows vista Business edition OS. I was wondering if I could use the recovery partition or do I have to use an installation CD. And by the way, just to give you a head I'm just a beginner and badly needs help. the problem I had is I get a strong signal for my WiFi, but again it is not connect to the internet it connects sometimes but then after I reboot my phone it comes back with the same problem, it connects to the internet, but I detect my network, someone told me to just reformat the entire system. I hope someone can give me a help step by step on how to do it. and also I do not see the product key for my system. your help would be greatly appreciated thanks

  Remember - this is a public forum so never post private information such as numbers of mail or telephone!

  Ideas:

  • You have problems with programs
  • Error messages
  • Recent changes to your computer
  • What you have already tried to solve the problem

  Hello

  Formatting/reinstalling is overkill. A bit like buying a new car because you have a flat tire.

  To reinstall, you can use either the volume of recovery or the recovery disc, both should work pretty much the same. In general, the product key is located on the system like a sticker (on laptops usually on the bottom). If you can't find yours, you should contact the provider or your network administrator (and in fact, if there is a working system, you should contact them before doing anything).

  Before you do this right, you can try this: click Start and type CMD. Right click on the menu entry that appears and choose "Run as Administrator". Click on continue in the UAC prompt. From the command line, run:

  ipconfig/release

  ipconfig/flushdns

  ipconfig / renew

  Allow everyone to finish (return to the command line) before proceeding to the next. When you are finished, close the command prompt. See if that helps with your problems of connection.

  Good luck, Rick Rogers, aka "Crazy" - Microsoft MVP http://mvp.support.microsoft.com Windows help - www.rickrogers.org

• Restarted my WRT160N, now my laptop connects to my network but will not connect to internet

  I forgot my password to the original network so I restarted my WiFi router, now my computer reconizes my home wireless network and connects (accepted the new password and all), but when I open my browser, it cannot connect to the internet. My internet connection still works when I plug my laptop directly into my cable modem, and my laptop says that I'm connected to my wireless network, so I don't know what the problem is here.

  I was pulling out my hair for the last few hours trying to find a way to solve this problem, so any help would be greatly appreciated.

  Thank you

  Go here to check your cable configuration.

• WRT54G will connect to the network but will not connect to internet

  Guys, I installed an older Linksys CM100 cable modem and when I did I lost the connection to the internet using the WRT54G Router. I can connect fine net when I go to right fromt the modem cable to the pc. I can use my home network very well. I did a firmware upgrade, does not. I'm losing my mind. It worked fine before the new cable modem. Does make sense to anyone? BTW, I can't connect to the internet via wired or wireless connections and ping www.google.com gives 100% packet loss. Ditto for a ping to 192.168.1.100 (cable modem) when the router is connected.

  Dear God please help me

  -Jacob

  Thus, because no one here was able to offer all the help, I called tech support and was very surprised. I was able to get a tech immediately and without going through the 1 million on the phone buttons. The service is in India, but I could communicate well enough with him, even though I usually have people of understanding of handful who speak English as a second language. The issue that I had was that the default IP of the modem cable (192.168.1.100) and ip address of the router (192.168.1.1) were too similar. Apparently, the fact that the 3rd number 1 for both series was the cause of the problem. We changed the IP address of the router to 192.168.5.1, power cycling it and unfortunately it worked.

• OfficeJet 6000 E609n - Wireless concludes SSID and secure network but will not connect

  I use Mac OS 10.5.8. I installed the printer for USB and went to the next step to configure wireless. My secure network, it obtains the SSID and then asks the WPA personal password for the network. I enter this and click on continue and the message comes back, "the Wi - Fi network selected «...»» ' is not within reach of the unit. ' Button choices are 'Change network' or 'Retry '. Despite attempts unsuccessfully repeated. However, I scanned for other networks and found a secure and connected to this network. Go figure. My router is sitting on my desk next to the printer. The router is a D - Link DIR-655 n I'm on cable for ISP services. When I first bought the printer, we were away on vacation, and I've successfully added to my Mac laptop. I have reset the printer found in the then successful and user guide to establish a connection to the House, with the unsecured network (I don't live in a condo so no idea whence the other network). Thank you.

  You can try to update the firmware on your router.  Some of these models have had problems with HP printers and Netgear was subsequently fixed it with a new version of the firmware.

• Watch WiFi is connected but will not connect to internet

  I have an iPad 2 which, all of a sudden (in the Middle streaming), is more connected to the internet.  I rest the network settings, when this does not work, I have reset all settings, stopped and rebooted, all done basically.  It shows that its connected to my WiFi, but will not connect to internet.  All the other devices in my house work, then there must be a problem with the iPad.

  Reset the router: just pull the power for a few seconds and reconnect. No parameter to get lost.  Other devices operating with success is not serious. The router has probably received an invalid address for the iPad.

• Take the tool does not. Take the tool selected - can see the hand but will not take anything

  Hello

  I'm new to photoshop and I am currently working through the tutorials on Lynda.com to learn as much as I can, but I'm stuck at the minute. Tutorials wants me to use the Snipping Tool to move an image and no matter what I do nothings moving. I selected the tool and see that it is selected and that the needle moves on the image but it is not striking, no selection.

  I also did with the letter to select the capture tool. Once again, this works, but will not take anything.

  Any entry in this problem would be highly appreciated. Thank you

  Hi Clara-beautiful,

  Hand tool is running when your image is enlarged and that you want to move to a specific part of the image.

  You must move your image with the mouse after a zoom once you have selected the hand tool.

  Are you a person following the same steps in workflow or other?

• Satellite L300-1AS - error PXE - boot error - will not boot from USB

  Startup error - error PXE-L300 1AS - will not boot from USB

  I recently bought a new HD to replace the original that my laptop takes an hour to load.

  I put the new drive hard at in the BIOS setting, I chose to boot from USB... USB is recognized as it appears on the screen of the BIOS. I disabled the LAN option as it gives me PXE error... I think that the USB files are not read. as I handed the old HD and attached to boot from USB but it just goes to the start screen.

  I thought that perhaps I bought the wrong HD, but a new appeared on the BIOS setting... I'm a bit confused and would appreciate it if someone could point me in the right direction...

  Any help or advice will be appreciated.

  Thanks in advance.
  Abul

  New HARD drive has nothing to do with it. Problem must be your USB key.
  In your ad you didn t wrote what is on it, and we don t know if USB can operate as boot device or not.

  I put t know what OS you want to install right now but original recovery DVDs or use Microsoft installation disc and install Win7 32 bit. I ve installed on friends L300 and it works perfectly.

• Network Assistant will not connect pc to the LAN, but connect to the internet properly

  My main PC had been connected to a local network of four PC but abruptly dropped from the network.  I can connect to the internet OK, but the wizard does not reconnect me to the local home network.  I read other articles on test and checks and everything seems to be okay, but when I check my network places other computers are running and are not displayed.

  Try the following and see if it helps:

  "You can not access the shared files and folders or browse computers in the workgroup with Windows XP"
    <>http://support.Microsoft.com/kb/318030 >

  HTH,
  JW

• HP LaserJet 200 colorMFP M276nw connects to my wireless network, but will not recognize the printer

  I am trying to set up my wireless printer, and the printer says its is connected to my wireless network, but I can't get my computer to print wireless if I disconnect my regular network and attach the direct wireless network name, which is different and stops my internet to work. How can I get my computer to recognize the printer on my regular wireless network?

  Hi @lelg,

  I understand that you want to configure the printer on the wireless network. I can help you with this.

  Uninstall the printer software.

  Uninstalling the printer software.

  Restore the default settings of the printer.

  Go to Configuration, restore the default values.

  Cycle power to the router and the computer.

  Run the installer on the printer wireless.

  Go to the configuration, Setup, menu wireless network, Wireless Setup Wizard.

  Print a configuration page to get the IP address of the printer.

  Print a Configuration report.

  Select the method.

  If you have a valid IP address for the printer, then try and access the Web built-in to the printer server. Type the IP address in the address bar of your web browser. (Internet Explorer)

  If it loads the page from the network printer then the printer is on the network.

  Download, save, and then run the installation of the software. Color HP LaserJet Pro 200 pilot M276nw MFPS.

  Select your operating system, click Next and click on the software to download and install.

  Test the printer.

  What operating system do you use? How to find the Windows Edition and the Version on your computer.

  Please provide detailed results if you're still having problems.

  Good day!
  Thank you.

• Intel WiFi Link 1000 bgn @ E220s: visible, but will not connect to access point

  Hello

  just got my new E220s - love it! Only problem is that I can see the wireless access points, but whenever I try to connect to them it says: "Windows could not connect to '.»»

  My setup is a Lenovo TinkPad E220s: Intel Core i5, Intel WiFi Link 1000 bgn, Bluetooth 3.0, 7200 RPM 320 GB HDD, 4 GB RAM, Windows7 Home Premium.

  My system is up to date with regard to the update of Windows and Lenovo BIOS update.

  * A tried to connect to a FritzBox 7141 (b, g, g ++ standards)

  * with WPA - PSK: entered the password-> problem as above

  encryption-> problem as above

  * Connection I tried with 'eduroam' (wifi popular education in the world)-> problem as above

  * Using the driver Lenovo 14.0.1-> problem as above

  * Manually install driver Intel 14.1.1.3-> problem as above

  'Manual Diagnostic tool' Intel:

  * test hardware: past

  * pilot: past

  * radio test: past

  * scan test: past

  * association test: failed

  * other tests: does not work

  Some diagnoses more Windows:

  Details about network adapter diagnosis: Network adapter Wireless Network Connection driver information: Description . . . . . . . . . . : Intel(R) WiFi Link 1000 BGN Manufacturer . . . . . . . . . : Intel Corporation Provider . . . . . . . . . . . : Intel Version . . . . . . . . . . . : 14.0.0.113 Inf File Name . . . . . . . . . : C:\Windows\INF\oem14.inf Inf File Date . . . . . . . . . : Tuesday, November 09, 2010 8:43:32 AM Section Name . . . . . . . . . : Install_MPCIEX_Lenovo_1000_HMC_BGN_WIN7_64 Hardware ID . . . . . . . . . . : pci\ven_8086&dev_0084&subsys_13158086 Instance Status Flags . . . . . : 0x180200a Device Manager Status Code . . : 0 IfType . . . . . . . . . . . . : 71 Physical Media Type . . . . . . : 9

  Hello

  Problem solved. Of wire antennas was not of all attached to the card and the other it has established relationships by chance. It took me 3/4 of an hour to turn off the battery, remove the keyboard, attach wires to the NIC (quite difficult due to lack of space) and put it all together. Then everything worked fine.

  Thanks for the help, forum!

  E220s rocks!

• My IPad is connected to the WiFi router but will not connect to internet. My Internet works on my IPhone and Mac Book

  Since last night, my IPad connecting to my WiFi router, does not connect to the internet.

  Internet connection works for my IPhone and MacBook.

  Hello

  Go to settings resets the network settings on iPad.

  After reset, enter your key wireless router.

  See you soon

  Brian