Satellite L50 - A - 1 5 PSKK6E does not start after upgrading memory

Similar Questions

• Satellite A200 PSAEOE does not start after upgrading memory

  Hi, I am first time here.

  I bought a Toshiba A200 PSAE0E-03J02JDR with 2 GB of RAM. I bought a pair of ram Corsair (2 * 2 GB VS2GSDS667D2). The computer does not start after that I installed the memory. I have intel 945 chipset, which is capable of 4 GB (manual page 1-2). The bios version is 1.8 2007.

  Can anyone help me, please.

  Post edited by: Marian ovidiu

  Hello

  The A200 series supports different chipsets;
  Intel 945 PM
  Intel 945GM
  Intel 943GML

  As far as I know your laptop supports the * 943GML * Intel chipset and the chipset supports 2 GB RAM max.
  Take a look at your laptop s user manual * Page 18.*

  Summer: 4 GB of RAM are not possible, and therefore your laptop does not start.

• Satellite 1410-304 does not start after upgrading memory

  I tried to extend the memory of 512 MB to 1 GB by placing two memory modules in my laptop Satellite 1410-304.
  These blocks of memory are each 512 MB and type: DDR400 PC3200 SODIMM.

  Each memory separate block in one of the memory slots A or B works well, no problems.

  However, when the two blocks of memory are installed, the laptop does not start no more.
  I hear the soft beeps indicating that a problem has occurred. The system works under Windows XP.

  Someone who can tell me how to solve this problem. Thanks in advance for your help

  concerning

  Marten

  Memory sticks are made by the same company? If this isn't the case, it will not work.

• Satellite L100 113 does not start after upgrading memory

  Hello.

  Our Integrator bring to our company KVR800D2S5, but laptop memory modules does not start :(

  I read manual - this laptop supports 533 PC4200 memory modules.

  But SO-DIMM 533 MHz will be delivered in one month...

  The memory modules, we can install to Toshiba L100-113?

  Thank you.

  Hello

  I think that the laptop does not power upward because of a barrette memory faulty or not fully compatible.

  Please visit this memory 3rd party:

  [Memory for Toshiba Satellite L100 113 | http://www.orcalogic.co.uk/asp/prodtype.asp?prodtype=22360&ft=m&st=3]

  As you can see Satellite L100 113 memory can be upgraded up to 2 GB (2 x 1 GB) and you must use the DDR2 533 MHz (PC2-4200) 200 - PIN SODIMM

  Concerning

• Satellite A60-672 does not start after upgrading memory

  Hello

  I bought an additional memory for my laptop, but after installing it the PC will start is no longer, when I turn it on it makes a brief noise then nothing. After taking the memory expansion out again once, the laptop still does not start.

  Peter

  Hello

  I agree with "guy sos." There is no doubt motherboard problem now. I assume you used the incompatible memory module.

  In any case, contact the after-sales Service of Toshiba partner in your country and explain to them the situation. The address that you will find under http://www.csd.toshiba.com/cgi-bin/tais/su/su_gaspLocator.jsp?pf=true

  Good bye

• NB305 - does not start after upgrading memory

  Have just bought 2GB memory update for Toshiba NB305-106, and it does not work. Machine unbootable - started 1 GB module.

  Just read a post on memory upgrade problems - different users having problems and they used Crucial memory without any problems. -Is it true?
  Anyone got an advisor?

  Hi ian123,

  If the boot netbook doesn't, additional memory module which means this module is not compatible and you need another.

  It would be interesting to know which module you are buying exactly and what specs it has.
  Can you post this information?

  In General, I have good experience with the modules of Kingston

• R50E does not start after upgrading memory

  I tried to upgrade this laptop from the factory of 512 MB to 1.5 GB. I got a Kingston 1 GB DDR - 333 SO-DIMM, but after I installed it, the laptop does not turn. Only the power led is lit.

  I don't know why this happened, because all tests indicate that it should work.

  1. the new stick is ok. I tested it in another laptop and it worked. I also cleaned the contacts with isopropyl alcohol.

  2. the memory locations are ok. The old memory works in each slot.

  3. I tried to install the new one stick in a slot and it did not work.

  4. This update is officially supported by record of IBM and BIOS is up to date (v2.1, December 2006).

  Unless I'm missing something there is a confusing question. Unfortunately, I don't have an another 1 GB DIMM to test with.

  yehuda1 wrote:

  TBut I don't think it's a matter of density. something fundamentally wrong with this system. I just discovered that I can not upgrade the memory somehow, even not with a stick of 256 MB. The system starts only with the current key.

  OK... This is not good, but I have to tell you that...

  I guess it's time to throw the boy part of retirement and move to a new machine...

  Good luck.

• Satellite M30X-122 does not start after upgrading memory

  Hello

  I want to upgrade the RAM in my Satellite M30X 122. Correctly my NB contains 2x256MB.
  I bought a GB 1 333 MHz. Cl2.5 module PC2700 (corresponds to the former, but more grand ;-)))
  Now I build in the module, but after the build-in system is dead.
  It doesn't show anything on the screen (after pressing the button one)).

  Does Anyboby have some tips?

  Thank you very much
  Peter

  Hello

  Toshiba has recommended the use of these memory modules:
  PC2700 256 MB (PA3311U - 1 M 25)
  PC2700 512 MB (PA3312U - 1 M 51)
  1024MO PC2700 (PA3313U-1M1G)

  Well, the size of 1024MB should be compatible. In this case, it s not a module size.
  Have you tried to get into the BIOS? BIOS recognizes the memory module?
  Maybe the module is broken?

  In my opinion, you should check if the module memory works on a different unit. If this module works correctly on another unit if your M30X doesn t support this module of memory and you need one another.

• Satellite C660D-107 does not start after upgrading memory

  Hi all

  I just bought a Kingmax 4 GB 1333 Mhz memory for my laptop C660D-107.

  Yesterday, I put and I saw on the BIOS if the laptop recognizes it or not.
  The laptop showed the 4 GB memory but when I booted the machine nothing happened.

  Black screen and nothing else.
  The specification to write 8 GB of RAM maximum (1066 Mhz).
  I think that 4-4 GB. The frequency is perhaps the problem?
  Opus 64-bit Win7 system

  concerning

  Robert

  Hello

  The bus front end (FSB) manages 1066 Mhz max.
  Thus, your memory at 1333 Mhz Kingmax cannot operate at 1333 Mhz.
  Usually, this should not be a problem and modules more quickly would run slowly at 1066 Mhz but there may be a compatibility issue.

  Edit the memory at 1066 Mhz I have so I recommend using modules from Kingston and hand never any problem.

• Satellite M100 does not start after upgrading memory

  I recently bought two sticks of DDR2 1 GB 533 Mhz RAM memory.
  I placed both in the slots (the one under the keyboard and one at the rear).

  For some reason any when I try to turn the computer back on to, nothing happens.
  The screen is black and nothing seems to load.

  Help please!

  The case is clear like a Crystal;

  The M100 cannot start because memory modules are not fully consistent or both modules or only a single module is defective.

  I put t see any other solution to test for laptop with other modules

• FF does not start after upgrading to version 27.0.1

  FF does not start after upgrading to version 27.0.1
  Crash ID: bp-2bc18734-d643-4843-a10f-fd6102140214

  Firefox 27.0.1 is too recent for me to know what unique issues it may have. I will message you a link to download the installer for Firefox 27.0 to see that the inversion or not the problem.

• Satellite P200D-130 does not start after upgrading RAM

  Hi, I just upgraded the RAM on my P200D 130 but it does not start after that.
  I removed the 2 Hynix 1 GB PC2-5200 and put in 2 SO Kingston DDR2 2 GB PC667 (should be the same as PC2-5200).
  Post-market nothing happens, light power control is turned on, I him stays CD drive but screen black, no beeps.

  I put one of the 1 GB modules, it starts normally, then I tried a 1 GB into the lower slot module and a 2 GB module in the top slot and it works.
  I tried a single 2 GB module in each slot, even in the form of 2 2 GB modules.

  What could be the reason, better: what would be the solution to ensure that the modules of 2 x 2 GB to work?

  Thanks in advance,

  Michael

  Hello!

  I think that both modules are not compatible to the laptop.
  Normally you can upgrade your laptop to 4 GB. Look in the user manual.

  The RAM, you should bring the computer dealer and request a new one. More buy modules with the same specifications and dimensions. Try buying RAM with the same specs as before.

  Good bye

• Re: Smoker L30-10 X PSL33E does not start after upgrading RAM

  Hello

  I have a problem with my laptop.
  It has 1024 MB of RAM (2 x 512), but it wasn't enough, so I decided to update to 2048 MB (2 x 1024).

  I bought two modules and my computer does not start after changing them.
  It was only a screen black (same BIOS has not started). I tried another combination of installation of memory modules RAM.
  2 x 1024 - did not work
  1 x 1024 - did not work
  1 x 1024 + 1 x 512 - working but not properly.

  BIOS find that I only 896 MB (1024-128 for the video card)
  I said OK. Let's see what will show windows. He was also 896 MB.
  I launched CPU - Z and it shows that the total size of memory is 1536 MB (medium detect both modules).
  I found that CPU - Z detect 1 module 1 024 MB and 512 MB secondary, but the BIOS detect only 1024 MB 1536. How is that possible?

  I have fought, is that my BIOS is old, then I update the toshiba Web site form most recent version, but the problem persists.
  Please someboy help me and tell what to do.

  PS. the Modules are new and work correctly.
  They have been tested.

  Hello

  Have you used two identical RAM modules?

  What kind of modules did you use?

  In my view, that the problem is related to the new, inserted modules.
  There must be something wrong with the modules or modules are not completely compatible if the laptop can not boot after installation.

  According to a few pages of the book handles the DDR2 533 MHz (PC2-4200) 200-PIN SODIMM modules.

  Did you use these modules?

• Satellite L670-1EE does not start after upgrading RAM 4 GB to 8 GB

  I'm trying to upgrade the RAM from 4 GB to 8 GB. If I replace two 2 GB of 2 modules of 4 GB modules, the BIOS (which is the most recent) realize the 8 GB, but does not start at startup. There is just the white cursor blinking not.

  When I put in the 1 4 GB module and 1 2 GB module the system starts without a problem and has 6 GB. I checked the two 4 GB modules, they work in any combination, but not when both are installed together.

  I couldn't find any rider or the settings of the bios for the RAM...

  Any idea?

  Thanks in advance for the help

  The last plausible explanation is that both modules are ok, but not compatible with each other.
  The laptop can be upgraded up to 8 GB of RAM. This should not be a problem since the unit is supported by the Chipset Mobile Intel HM55 Express.

  So I think that you need to replace the modules Kingston modules are great and work without problem.

• Satellite Pro A200 PSAE4E does not start after upgrading BIOS XP

  Hi, I need help!

  computer laptop, tested just got everything ok with Vista business and everything works fine.
  Now, I have a requirement to test a laptop duel boot XP build and follow the attached instructions to change the BIOS so that I can install XP.

  Restarted the laptop with the bios disk selected bios XP and everything seems ok.
  The phone rings, I answer. When I finished, I think back to the laptop and screen is white.
  Leave it for 20 minutes still white. Stop the laptop and reboot, no tosh start screen, nothing.

  Now does not start, so what do I do to get this thing working again?

  Hey Buddy...

  This looks very bad! :(il ressemble pas à quelque chose a mal tourné àle cours de la procédure de mise à jour dele de BIOS, et donc l'ordinateur portable ne peut pas démarrer correctement.)

  I hope that the ROM module must be flashed again.

  This can be done only by an authorized service provider.
  I see no other solution for contact ASP in your country and ask for help and handling.

  Good luck and best regards