Satellite L50-A01Q - WLAN not detected after installing the Atheros WLAN driver

Similar Questions

• HP pavilion g6 - not able to install the Atheros Wireless Driver

  Hello, I installed windows 7 ultimate 64-bit on my HP Pavilion G6. But when you try to install the atheros driver I get the error message "card not found 802.11a/b/g/n wireless network device.

  My network ID controller hardware is "PCI\VEN_14E4 & DEV_4727 & SUBSYS_1795103C & REV_01".

  Help, please.

  Hello:

  This is because your laptop is an according to the hardware ID Broadcom wireless card you have validated, if you need this driver instead.

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-107849-1&cc=us&DLC=en&LC=en

• Satellite A500 - 18Q - battery not detected after installing Windows

  I have Satelite A500 - 18Q (PSAR3E) and Windows 7 32 bit

  Windows is not detected battery. What should I install to the Windows recordnize the battery?

  Hi marnin,.

  Have you installed Windows Toshiba Recovery disk or normal drive of Microsoft?

  Normally for the battery you n t need an additional driver. He will be recognized automatically.

  Can you charge the battery when the laptop is turned off?

• CD player not recognized after installing the second hard drive

  My OptiPlex 755 Windows 7 with a ran fine until I installed a second hard drive.  Now only the hard drives are recognized.  I have cd players connected to SATA 2 and 3 a the SATA drives 0 and 1.

  The 755 a 0 and 1 and then 2-3 THEN esata.

  Other chipsets have 0 1 2 3 4 5 and raid 5 capacity.

  These options appear as
  SATA 3
  for the mini tower,.
  SATA
  0
  through
  SATA 2
  for the
  Desktop
  for

  The blue connector is drive 0

  The 2nd Black, this is the dvd's.

  There is no car setting just the port enabled or disabled.

  2nd HARD DRIVE GOES ON THE WHITE CONNECTOR

  The 2nd CD GOES ON THE CONNECTOR FOLLOWING

  DRIVE CABLE IS BLUE AND CD CABLES ARE ORANGE.

  

  

  

• My MBP in trouble after installing the Wacom Intuos driver.

  My MBP takes almost 5 minutes to start after installing the Wacom Intuos driver, I remove and reinstall but no change!

  and it seems that the machine was very unstable and very slow, sometimes the beach ball appears and no response for a few minutes and works again!

  I try to contact Wacom support in Hong KONG but still no body to answer my call...

  Can be resolved by upgrading to IE captain? Thank you very much!!!

  Wacom driver: 6.3.15 - 1

  News by cheque to be:

  EtreCheck version: 2.6.6 (226):

  MacBook Pro (13 inch, late 2011)

  MacBook Pro - model: MacBookPro8, 1

  1 2.4 GHz Intel Core i5 processor: 2 strands

  4 GB of RAM expandable

  Bluetooth: Old - transfer/Airdrop2 not supported

  Wireless: en1: 802.11 a/b/g/n

  Battery: Health = Normal - Cycle count = 87 - SN = W01457N9TD3BA

  Intel HD Graphics 3000 - VRAM: 384 MB

  Color LCD 1280 x 800

  OS X Mavericks 10.9.5 (13F1507) - since the starting time: 4 hours

  Disc information:

  HGST HTS721010A9E630 disk0: (1 TB) (rotation)

  EFI (disk0s1) : 210 MB

  1 t MBP (disk0s2) /: 999,35 go-go (590,22 free)

  HD (disk0s3) [recovery] recovery: 650 MB

  MATSHITADVD-R UJ - 8À8)

  Configuration files: (Does that mean?)

  / etc/hosts - Count: 57

  Startup items: (Does that mean?)

  PenTabletDriver: Path: / Library/StartupItems/PenTabletDriver

  Startup items are obsolete in OS X Yosemite

  Launch system officers: (Does that mean?)

  [loading] com.apple.RemoteDesktop.plist -invalid signature!

  [loading] com.apple.screensharing.MessagesAgent.plist -invalid signature!

  Top of page process CPU: (Does that mean?)

  55% mdworker (3)

  4% kernel_task

  4% WindowServer

  2% fontd

  2% hidd

  MacBook Pro, OS X Mavericks (10.9.5)

  Speed up boot times-

  Start time - speed (2)

  Start time - speed (3)

  file/etc/hosts - fixing a pirate

  You might also consider adding more RAM. 2 places I've seen recommended more to buy reliable RAM are below. I have bought RAM several times to other World Computing and have always been very satisfied with the product and the service. They have instructions online on how to replace the RAM. OWC has also tested the RAM above what Apple says, it is the maximum. Now, I have 6 GB installed on an iMac 2008 so-called beginning limited to 4 GB and noticed an improvement.

  Crucial

  Other World Computing

• I'm having trouble installing Photoshop CS6 after installing the new hard drive.  What do you suggest me?  Tony

  I'm having trouble installing Photoshop GS6 after installing the new hard drive.  What do you suggest me?  Tony.

  CS6 - http://helpx.adobe.com/x-productkb/policy-pricing/cs6-product-downloads.html

  You can also download the demo version of the software through the page linked below and then use your current serial number to activate it.

  Don't forget to follow the steps described in the Note: very important Instructions in the section on the pages of this site download and have cookies turned on in your browser, otherwise the download will not work correctly.

  CS6: http://prodesigntools.com/adobe-cs6-direct-download-links.html

• WIFI device not detected after installing Windows updates.

  Original title: WiFi stops working when loading Windows (Win7).

  After that the last series of Win7 update is more my Wi - Fi works.

  My computer is the only one in the affected House. Wi - Fi is on (the radio light is on) when you start up loads of Windows, and then he went. More my factory installed Atheros wireless network card is no longer visible in the device, only the Ju Fast Ethenet controller Marvell Manager. I have re-installed the Atheros driver in the hope that the system would then find the device. No luck. Even the F8 key is operable, so using the FN + F8 key to activate the Wi - Fi is a bust.

  We know that the camera is good, but Windows doesn't see a reason any. This seems to be a matter of Win7 and not a hardware problem.

  • Please let know us if there is a FIX to this problem - I spent the last 4 days of research on this and I'm not alone.
  • I can re - install Win7 or y at - it a patch that I can use? With the help of a cable Ethernet is well when you're used to a Wi - Fi connection!

  & Devices:

  Toshiba Satellite P305D-S8818

  Atheros AR5BXB63

  Hi CDanahy,

  1. What are the updates recently installed?

  How to find the number of update:

  a. click Start, type windows update and press enter

  (b) in the left pane, click view update history and find the updates recently installed.

  2. are there any yellow listed under network adapters, Device Managerexclamation?

  To check:

  a. click Start, type devmgmt.msc and press enter

  b. expand the network adapters and make sure that the exclamation points.

  Method 1: Run the Microsoft fixit

  See the following site:

  Hardware devices do not work or are not detected in Windows

  http://support.microsoft.com/mats/hardware_device_problems/en-us.

  Method 2: Disable any security software

  See the following site:

  Disable the anti-virus software

  http://windows.microsoft.com/en-us/windows7/Disable-antivirus-software.

  Important note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

  Method 3: Clean boot

  See the following site:

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.microsoft.com/kb/929135.

  Note: to set the computer back to start normally, use the step 7 in the same link.

  Note: If in case you are connected through a wireless connection and then when you start the System Configuration utility to perform the clean boot, click Startup and Services tab one time and check see topic wireless are turned on (Enabled).

   

  I would say as you to see the site mentioned below:

  How can I troubleshoot network card?

  http://windows.microsoft.com/en-US/windows7/fix-network-adapter-problems.

• Sony VAIO VPCJ111FX touchscreen not detected after installed Windows 8.1 (clean)

  I had to install the new hard drive in my Vaio, needless to say due install the new OS... Figured since it's touchscreen Windows 8.1 would be the way to go.  Yes, well now a my touch screen does NOT work!  What is the problem with that?

  Sony VAIO VPCJ111FX

  8.1 Windows x 64-bit

  500 GB HDD SATA/7200 RPM/MIN/32 MB cache

  p. s.

  YES, it IS a touch screen!

  Hi DCwell1977, while they inspected the drivers of this model, it seems that this unit doesn't have drivers available for Windows 8.1. You can also visit this link and check the compatibility of this model to Windows 8.1. It's not necessarily you cannot upgrade to Windows 8.1, but we cannot guarantee that all the features of this unit will work.

  If my post answered your question, please mark it as "accept as a Solution.

  bit.LY/LapMagWin

• HP EliteBook 8440p: Best boot option after installing the new hard drive and put to memory.

  I just installed the new hard drive for my laptop and will get the cards of two memory installed tomorrow. I would like advice on what would be the best option to start when the laptop for the first time I'm on fire.

  I have the original Windows HP recovery disk came with the computer.

  I also have a recovery disc and a system image on disks created with Macrium Reflect two days ago.

  I also have a recovery disc and a system image is created on an external hard drive Seagate two days ago. (I've read mixed reviews on these is currently working as a media of rescue with Win7 Pro).

  I guess if I use the HP recovery disc I would be then just use any system image I prefer, without the recovery disk. Anyone know if it makes a difference at all which method to use?

  bozzle73

  My recommendation would be to restore using the image of MR (Macrium Reflect) you did.

  But then, I used Mr. on all my PCs for years and am a big fan - having had it Miss ever in the years and years of use.

  You will need boot from the boot of MR media (you did that right) and, if you photographed all the required partitions for the operating system, restore it on the new drive should take a few minutes, and when this is done, you reboot and everything should be OK.

  Good luck
  
  I'm a volunteer and I do not work for, or represent, HP.
  ========================================================================
  If you feel that my suggestions helped you, please click on the thumbs-up symbol to say thank you!
  
  If they helped to solve your problem, please click 'Accept as Solution' to help others find similar information.

• How to restore the operating system after installing the new hard drive?

  After installing a new hard drive to replace a disc that fails, can you install windows 7 and the other necessary "tricks" to re-setup and driver discs Dell came with the computer? or you buy a new copy of windows 7?

  See the Dell system software installation

  I can find the most recent versions are:

  Windows XP x 86 http://ftp.dell.com/utility/Dell_System-Software_A06_R288017.exe

  Windows XP x 64 http://ftp.dell.com/utility/Dell_System-Software_A07_R288023.exe

  Windows Vista x 86 http://ftp.dell.com/FOLDER31331M/1/DSS_UTIL_WIN_R282536.EXE

  Windows Vista x 64 http://ftp.dell.com/FOLDER88660M/8/Dell_System-Software_A06_R282537.exe

  Windows 7 x 86 http://ftp.dell.com/FOLDER88692M/9/Dell_System-Software_A03_R282539.exe

  Windows 7 x 64 http://ftp.dell.com/FOLDER88677M/8/Dell_System-Software_A03_R282538.exe

• Satellite P300 - Microphone is not working after installing Windows 7

  Hello

  I recently did a clean install of Windows 7 on my Satellite P300. The microphone has been fine with Vista but does not currently work with Windows 7.
  I tried to go to the sound section and it does not list the casting Mike - just struggling. Can anyone help?

  Thank you
  James

  Hello

  Maybe you didn't install the driver for the microphone? Therefore, you will need to install the driver for the webcam, because the microphone is a part of it. You can get it here:
  http://EU.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download drivers

  After that, it should be possible to use the internal mic.

  By the way: internal what application you are using for the microphone? Skype or something?

• NETWORK card not detected after installing ESXi 4.1?

  Hi all

  I installed the ESXi Server 4.1 on a single server with the following configurations,

  CPU = Intel (R) CPU Xeon X 3430 @ 2.40 GHz

  Memory = 16GB

  NIC = Intel 82574 L Gigabit Network connection-2 no

  After that ESXi installation a NIC card not detected. But two cards network is the same configuration. Due to this problem, I can not configure grouping of NETWORK cards. Please suggest me. Thanks in advance.

  Hello!

  On the screenshot that you are using a motherboard Intel S3420GP. Just a NETWORK card is 82574L, the other on board is a 82578DM, which is not supported. So you will need additional network cards.

  See you soon,.

  Martin

• Satellite A500 - TV tuner not recognized after installing updates

  Recently, I ran a few updates (Windows 7) for Satellite A500 (PSARA9A). It has a built-in tuner & it worked fine until updated. Now when I go to watch television or check it comes up with "No tuner available to meet the demand for courses".

  I tried to install the new driver, but I can't tell if he does something. Device Manager me indicates that the latest drivers are installed, but it shows the yellow exclamation point.

  Can anyone suggest anything here?

  In my opinion you should try to roll back the OS to an earlier time using System Restore tool.
  This should be a quick and temporary solution.
  After this check the functionality. I put t know what settings do you use for Win updates installation but I suggest you turn off the automatic option.

  Later when you will be informed about available updates checking a little list and if a driver update is listed here don t install. Use the original Toshiba drivers only.

• [E530] GPU NVidia not detected after installing Windows 10

  Hello.

  I have upgraded to Windows 10 a month but noticed now that NVidia gpu is not detected. I tried to disable and re-enable it in the bios but nothing helped. Is - this common problem (I guess not, since I have not found similar positions) or is there something wrong with my hardware or something? What should I do?

  Well, I installed Win 10 once again and now it seems to work.

• Satellite L305D - Touchpad does not work after installing Windows 7

  I had recently installed Windows7 32 Bit there is almost a week on my Toshiba Satellite L305D-S5934, and now the tablet to the PC no longer works.

  I was reduced to using an optical mouse on my computer. I've updated all my drivers and firmware etc on the windows update software and still I have not been unable to get the touchpad working. Windows 7 had installed the driver of synaptic for the touchpad pointing stick, but im guessing that he needs a special Tosiba firmware to recognize the touchpad for this model. What should I do to get the touchpad working again?

  Here are the specs of my model:

  PC x 86 ACPI
  64-bit AMD Turion X 2 processor
  ATI Radeon 3100 graphics card
  Synaptics PS/2 Port TouchPad

  I installed Windows 7 on my Satellite Pro P300 and touchpad works properly. The OS is naked and I didn't install any additional touchpad driver.