Satellite L50-B-177 - after upgrading the BIOS can not use the Polish symbols

Similar Questions

• After upgrade blackBerry smartphones - can not use headphones! Only the speaker!

  After the upgrade to the new operating system, I can't use the headset.   I hear nothing and no one can hear me speak.  When I change to speaker that works - but who wants to go through life with everyone heard your calls!

  This phone is essential for businesses and I am very frustrated - thought the new upgrade, it would be better, but it made it worse.

  Can someone help me please? !!!

  It happened to a number of us.  It takes some futzing with it to return to normal.  You have the headphones supplied with the phone?  Headphones or, for that matter?  If so, try connecting and then doing a battery pull.  With the connected headset and the device on, remove the battery, wait a few seconds, then replace the battery and wait for the device to reboot.  Others have lived the media player and selected a song to play.  While the song is played, insert the headset, then click on the BlackBerry Menu button (the button with seven points next to the green button ' phone'), click Activate combined and see what happens.  You will have to perhaps to plug and unplug the helmet a few times to 'train' the phone again.  Finally got mine back to normal and it worked fine since.  Seems you just need a "jump start" with the activation of the handset to the headset.

  I hope this helps!

• Satellite P50T-A-115 after upgrade Win8.1 does not play sound on HDMI

  A newly acquired by Satellite P50T-A-115, I upgraded to win 8.1, all suggested upodates and drivers are installed.

  I have no sound on my home theater system, playing from my laptop, while the video is good.
  The sound is the internal speaker of the laptop.

  There is no other choice than to my internal speakers in the control panel.
  I have seen similar questions to other laptops, but have found no useful suggestions.

  Did anyone get this working on a P50T-A-115?

  Please check this thread
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=74149

  There was a similar discussion and the problem could be solved by the installation and update of drivers in the correct order and uninstall the Intel WiDi as suggested by Toshiba.

  Your comments would be appreciated.

• Satellite L650d-120 does not load after upgrading the BIOS 1.7

  After upgrading the Bios up to 1.70 my laptop is no charging current, but always works to the AC adapter.
  Can I do something on my own?

  Hello

  First of all, you should set the BIOS to default settings and need to save the changes.
  You must also leave the AC adapter plugged into the laptop for a longer period of time.

  Welcome them

• Problem with Polish letters on the Satellite L50-B-177

  Helllo,

  3 days ago, I bought Toshiba Satellite L50-b-177 and I installed all the updates proposed, including the new version of the BIOS 1.70.

  Right now I have problems with some of the letter Polish such as?,?,?.

  In some Polish letters programs do not work at all, and in others only some of them.
  I changed the language (Polish), type of keybord (Polish programmer), region (Poland) and many other options in poles and Poland. Does not always work.

  Can you help me? Should I switch my laptop?
  I contacted with the center of Polish service COMP, but they sent me to this forum.

  OLA

  Please check this thread
  http://forums.computers.Toshiba-Europe.com/forums//thread.jspa?threadID=78858

  I recommend you to check the external USB keyboard functionality.
  If external keyboard works properly, the problem could be linked to a malfunctioning internal keyboard.

  In addition its recommended recovery the laptop to factory settings and check the functionality of the laptop as part of the default factory setting.

  _UPDATE: _

  This seems to be realted BIOS bug and I guess you have to wait until the new BIOS will be published which could solve the problem

• Satellite 2800-600 - how to upgrade the Bios/Firmware?

  How can I upgrade the Bios and firmware on my 2800-600? I want to install a new Combodrive. Which drives are supported? Where can I find the drivers and firmware etc... Please let me know. Thank you.

  Another point of view - I bought MS Windows XP Pro and haven´t you have a PC to install it on. Can I install this OS on my Satellite? Will it work? Where can I find the drivers for touchpoint etc etc... Normally, the Toshiba works with Windows ME and I can not use ITunes on ME... if XP would be great - what do you think?

  Hello Jürgen

  In my opinion, if you install the operating system on the unit you you use the recovery CD provided because it has been tested and it works without any problem. But if you want to install another system on your laptop, you can use the original Microsoft OS and all the necessary drivers, you can find the Toshiba site.

  http://EU.computers.Toshiba-Europe.com--> support & downloads

  The update of the BIOS and the important information (i.e. how to upgrade the BIOS) you will find also on the Knowledge Base Web site

  http://support.toshiba-tro.de/KB0/TSB4A00SD000BR01.htm

  Good bye

• After upgrading the bios to version 2.13 t430u, it freezes at black screen

  Hi all

  After upgrading my lenovo T430u bios to version 2.13 it freezes at a black screen, and windows does not load. My machine has windows 7 Professional and the only way to make it work is to reset the bios settings, but after awhile, it freezes at black screen and windows 7 does not load again and need to reset the settings of the bios once more. Hope someone of you gyus can help me with this since is very frustrating.

  Lenovo has released a BIOS updated for ThinkPad T430u that resolves customer reports of black screen after upgrading the BIOS.

  CHANGES IN THIS VERSION

  Version 2.15

  [Problem resolves]

  -Fixed a problem with the black screen after BIOS update

  -Fixed a problem with the gray screen when turn off Bluetooth in the BIOS Setup

  V2.15 BIOS can be downloaded here: http://support.lenovo.com/us/en/downloads/ds031724

  Thank you

• Bluetooth not available after upgrading the BIOS on HP g62-a60EM

  After upgrading the BIOS, I can't use bluetooth, as I can't see it in Device Manager. I've updated the BIOS with the file sp55430 on the support site. Battery is not holding a charge, it runs out after about 30 minutes. Back BONE back then now, I can use bluetooth. My OS is Windows 7 Professional 64 - bit - Slovenian.

  If anyone can help?

  Kind regards

  Dragan

  Hello

  Try to update the BIOS again. After that make sure that the wireless and Bluetooth lights is lit. Also download and installed the drivers of bluetooth and verification.

  After the BIOS also check in BIOS if Bluetooth is turned on:

  Menu of the System Configuration > Integrated device options > Enable/disable integrated Bluetooth Radio device
  

• Tecra M7: Various errors after upgrading the BIOS version 3.30

  After that I updated my bios to 3.30 I have the following problem:

  -A edge wireless turns off after a while and can not be activated until I restart.
  -Battery information is wrong. I tested the system, I can use 1 hour after he said that my battery is 0%

  How can I solve this problem? I have to downgrade my bios version?

  Kind regards.

  Hi mate,

  Let's see if my advice would be useful for you:

  1. try to reinstall the driver by downloading the latest version of the driver on the Drivers Toshiba download site. What you could also try is to disable the powermanagment for the wireless network adapter. (Just go into Device Manager, find the wireless card, and that there should be an option with a checkbox to disable)

  2. it's really rare, never heard talk about this issue. One idea would be to change all the parameters powersaver to your machine so that the battery will empty without entering in the day before etc... Just let the machine work until the battery is empty. Then remove it for about 1-2 hours, reattach and start windows. The battery should indicate 0% and then you leave the machine to load the battery. (the machine must be turned on). I hope that the battery must show it s correct percentage after you complete these steps.

  Welcome them

  PS: Please write again if it worked

• Is satellite C855D - 13L - possible to upgrade the processor

  Hello

  I created this topic to see if it is possible to update or change the processor in my laptop... I can barely work with programs that I owe to the University...

  Next to the processor, which is a * AMD APU E1 - 1200 with graphics Radeon (TM) HD (2 CPUs), _ ~ 1.4GHz_*... I remember * RAM: 6 GB * and good video card: * AMD Radeon HD 7310 (3 GB) *.

  Thanks in advance,
  Cosmin

  Hi Cosmin

  The whole upgrade CPU is a little difficult.
  Let the facts:
  -Is this laptop manufacturers don t s support all updated CPU and don t advice these updates.
  -The fact is that laptops using special versions of BIOS modified for each series laptop and therefore different processors might be problematic due to the compatibility of the BIOS. In the worst case, your laptop would not start after upgrading CPU.
  -The fact is that your laptop supports the chipset AMD Hudson A68M and ONLY AMD processors would be supported by the chipset.
  -The fact is that laptop procedure disassembly is not very easy and there is a high risk of damage of the part while dismantling the unit.
  -The fact is that you will NOT see large performance gain after upgrading the CPU. I recommend you replace the HARD drive with an SSD for performance gain.

  Here are some facts that you should consider before considering the replacement of the CPU.

• I bought ipad air 1 after that 2013 but can not get the pages for free. Numbers and imovie I can. IOS9 running at the moment. I have pages when I connect on icloud on my pc. Can I transfer iPad app, because it is not in the ILO purchased in itunes.

  Hi everyone, this is my first post, also help on the post would be appreciated.

  I bought ipad air 1 after that 2013 but can not get the pages for free. Numbers and imovie I can. IOS9 running at the moment. I have pages when I connect on icloud on my pc. Can I transfer iPad app, because it is not in the ILO purchased in itunes.

  Thanks in advance

  Newbie

  The only way to install an ipad app is through the app store.  PC or Mac software does not run on the ipad.  Search in the contacts link at the bottom right of this page.  Give apple a call.

  I guess is the icon for pages in icloud for storing documents pages.  At the same time, apple had a cloud based pages.  Not sure what happened to her.

  R

• I have a laptop with Windows XP. After getting a virus, I scanned with AVG and removed the threat. After re-booting, I can not connect to wireless internet.

  I have a laptop with Windows XP.  After getting a virus, I scanned with AVG and removed the threat.  After re-booting, I can not connect to wireless internet.  The icon shows "acquiring network address".  I connected the router directly on laptop computer connected to the wireless network and still unable to connect.  I tried to restore the system as well, but the message says "unable to restore the system, no changes were made.  Help?

  original title: acquisition of network address

  Hello, Steve.

  Try this link below on how to reset IE and let me know if it helps.
  http://support.Microsoft.com/kb/923737

• Satellite A100 (PSAARA) - I can not use the remote control

  I used Toshiba A100 PSAARA, but now I can not use the remote control to operate all things?

  Thank you!

  If the remote control suddenly stopped working trying to restore the operating system to an earlier time using System Restore tool.
  If this does not help please let us know.

• I can not use the command share in safari, mail, notes, etc. since I updated to El Capitan (10.11.5). No way to solve it. Please help me.

  I can not use the command share in safari, mail, notes, etc. since I updated to El Capitan (10.11.5). No way to solve it. Please help me.

  There is a problem with your installation of OS X. The easiest way, but not the fastest way to fix it is to reinstall the operating system. Unless you are in a hurry or have measured access to the network, it is what I suggest, especially since I don't know if there are any problems with the installation. Please backup all data before reinstalling. You won't need the backup unless something is wrong.

  The below, advanced shortcut if it works, can save you some downtime (and the cost of a download of several gigabyte, if necessary.)

  1 back up all data.

  2. disconnect all external storage devices.

  3. start in recovery mode. Select a language, if you are prompted. The OS X Utilities appears. One of the options is to install OS X. This is not what you do.

  4. This step is only necessary if you use FileVault 2. If you don't know what's FileVault, you use it. Go to the next step. Otherwise, launch utility disk, then select the icon for the volume FileVault ("Macintosh HD", unless you have given it a different name.) It will be nested under another icon of the disc. Select open in the file menu and enter your login password when you are prompted. Then quit disk utility must be returned to the main screen.

  5. Select get online help. Safari will launch. While in recovery, you will have no access to your Favorites, but you won't need them. Load this web page.

  6. triple - click anywhere in the line below to select this option:

  chflags -R norestricted /V*/*/S*/*/Caches

  Copy the selected text in the Clipboard by pressing Control-C key combination.

  7. Quit Safari. You go back to the OS X Utilities screen.

  In the menu bar, select

  Utilities ▹ Terminal

  Launch the Terminal application. Paste in the Terminal window by pressing the command-V key combination.

  Wait for a new line ending with a number sign (#) to appear. Quit the Terminal must be returned to the main screen.

  8. Select

  ▹ Restart 

  in the menu bar.

  9. This step must be performed after the restart, and while you are logged as administrator, not in recovery mode. If you have only one user account, you are the administrator.

  Select and copy this line as in step 6:

  sudo /usr/libexec/xpchelper --rebuild-cache

  Paste in a Terminal as before. You will be asked for your login password. Nothing displayed when you type. Type carefully, and then press return. If you do not have a password, you will need to configure one before you can run the command. You can get a warning to be careful. Confirm. You don't need to display the warning.

  If you see a message that your user name "is not in the sudoers file", then you have not logged as an administrator. Log in as one and repeat this step. You don't have to repeat the previous steps.

  Wait for a new line ending with a dollar sign ($) below what you entered.

  10. make as in step 9 with this line:

  sudo /usr/libexec/*/app_sandbox_cache_builder --rebuild-cache

  You can then quit Terminal.

• I'm unable to connect to the internet and I also can not use the WinXP system restore.

  No internet connection and I also can not use the WinXP system restore because it gives me an error at the 'end' which said: it cannot be restored to an earlier date.  I run AntiMalware bytes and StopZilla and erased all that they found.  Now I can't even connect to the internet.  When I go to the command prompt, it gives me an error contact the Support of MS that I know means I have a virus or a trojan that I should just get a time out?  My other PC on the same network is fine and connected.  The NETWORK card is fine, just does not know how to get rid of what it is, I have and to top it all impossible to connect to the internet to try all of the tools that can help.  Someone at - it ideas?

  The error you get at the end of the restoration of the system is typical of some anti-virus programs (Norton, especially) that interfere with the restoration of the system.  Try to start your computer in Mode safe (on several occasions, key to tap F8 while your computer starts) and run safe mode system restore.

  Additional information is necessary to treat your network problem.  Try to bring up a command prompt (start-> Run-> "cmd") or if it does not, try (start-> Run-> "command.com") and enter the command:
  ipconfig/all
  and after the info that appears in the State resulting.

  Also, check the logs of your system related errors (start-> Run-> "eventvwr.msc") and click on 'System' in the left column.

  HTH,
  JW