Satellite L50-B-2CP - cannot set the wireless connection

Similar Questions

• Satellite P300 - 20 H cannot find a wireless connection

  Hello

  Can someone help me? My Satellite P300 - 20H can not find the wireless router.
  He works very well before both at home and work, nothing has changed, but the laptop now cannot find a connection.

  Everything works fine when I connect the ethernet cable, but as soon as I unplug NOTHING.
  The router is in the same location as always, and no electric element in surplus is around.

  I guess it must be something to do with the laptop because it is the same at home because it's a job, WITHOUT JOY.

  Thank you

  Richy.

  Ohhm man.
  There are many discussions on the problems of WiFi and I hope you read some comments here that provide some tips.
  Did you?

  Firstly it should check if the WiFi is enabled correctly.
  Activate WLan switch (LED should be lit) and use the FN + F8 to activate the WLan.
  In addition, the WLan configuration should be checked! (SSID, encryption type, password encryption, etc.)

  Last but not least make sure your WLan driver is up-to-date.

• Satellite L505-13F - impossible to activate the wireless connection

  Hello, I have connectivity problems with my Satellite L505-13F.

  I can't turn on the wireless connection. I press Fn + F8 and nothing happens. The indicator at the bottom of the laptom turns on.

  I though this would be a problem with the drivers. I downloaded realtek wlan driver here [http://aps2.toshiba-tro.de/wlan/?page=downloads], but it has not installed correctly. Then I used the toshiba software installer, but yet again, nothing has changed. I have Windows 7 Home premium 64-bit.

  Device management, I have seen that I installed a wifi driver. (Realtek RTL8191SE Wirelless Lan...) So, what the problem is?

  Any suggestions?

  Hey,.

  Something happens if you press other keys FN or FN + F8 doesn't work only? Normally with this key combination you can enable/disable wireless network card.

  In addition, it would be interesting to know what happens if you are looking for WLAN networks. You see your WLAN router?

  If all the keys FN n t work, reinstall the package of added value and utility to Support Flash Cards. Otherwise, it could be another problem and you should reinstall the driver again and make sure the firewall isn't blocking the connection.

  See you soon

• When I remove my computer and try to connect to a different wireless network Iget "windows cannot configure the wireless connection" what can I do?

  My "wireless connection" screen does not show available networks, but gives me the message "Windows cannot configure this wireless connection".

  Should what changes I make to connect to different wireless routers?

  Hello

  You should try another network you know for sure that it is Public and open (as in the Starbucks or McDonald's).

  Wireless in general, http://www.ezlan.net/wireless.html

• V715w cannot set the wireless network

  Reference Dell V715w printer.  W7 x 64.

  Firmware already updated, clean uninstall/install, restarted router & modem, disconnect, etc. (all bases).  The name of the network on the control panel of the printer says '7ff5c4 print server.  This isn't my SSID.  When reinstalling, I never get the window to select the wireless network; Instead, the Setup program goes directly to methods of connection/bug.  Any help?  How can I do a hard reset of the printer?  I already unplugged for a long time; I don't see a reset button. I already have the two software on the printer resets.

  Short version: printer not finding a decent wireless network; install the software never gives me the chance to choose the wireless network.

  wdprice3,

  It's confusing. I have this model and have minor problems with it.

  Unplug the printer from the wall. Remove the brick power for 60 seconds. This will reset the printer receives error messages. Maybe this will reset the printer.

  

  Rick

• I can use my laptop with internet connection by cable, but cannot configure the wireless connection.

  Wireless Internet

  can use my laptop with internet cable is plugged in, but I am unable to set up a Wi - Fi connection, even though two other laptops in the House are Wi - Fi. Tried the convenience store who said there is a button on the front of the laptop that I push to turn on wireless on, tried that, but nothing is. I have an Acer Travelmate 2410, can someone help me?

  Hi Karldawkins,

  What operating system is installed on the computer?

  As the error message clearly indicates that the wireless switch is disabled on the computer. I suggest you consult the manual of the laptop and try to turn on the wireless switch.

  If you still experience the problem, then I suggest you to contact Acer support to enable the wireless switch.
  http://support.Acer.com/us/en/default.aspx

• Windows cannot set up wireless connection.e. 871122.

  problems with the wireless network

  I have a netopia adapter and use it with Windows XP. I get windows cannot configure connection.e wireless. 871122 can help you. It is said

  Hello

  · What is the number and the model of the computer?

  · What is the service pack installed?

  · You have security software installed?

  You can check the link below and try the suggested steps: how to fix wireless network connections in Windows XP Service Pack 2: http://support.microsoft.com/kb/870702

• Satellite L50-A-103: cannot use the Nvidia GPU as default after Win 8.1 upgrade

  My Toshiba L50-A-103 has two graphics cards, an Intel(r) HD Graphics 4000 and Nvidia GeForce GT M 740.

  In my workplace, I use an external SyncMaster 2032BW monitor with a resolution of 1680 x 1080.
  I've upgraded to 8.1 Windows and I can't use the card nvidia as a default value.

  Now detects only Intel processors with up to 1366 x 768.
  Is there a solution to this problem?

  Hello

  Update you all Win 8.1 drivers and utilities that have been released for this model on the page of the Toshiba UE driver?

  After the update of the system Win 8.1 you must update the drivers in the correct order.
  The installation instruction is also available on the Toshiba driver page!

• Satellite M100: Cannot set the resolution 1368 x 768 on external LCD screen

  Satellite M100-179
  Graphics - ATI x 1400 card.
  Cannot set the resolution 1368 x 768 on connected usung Sub - D LCD TV Samsung 32R72
  There is no resolution 1368 x 768 in the available resolution list.

  The graphics card hardware support different screen resolutions, but if the driver doesn't contain this resolution of the screen so that you cannot choose it.
  I think so you re not able to choose this special resolution on the external display.

  In my opinion it has nothing to do with the graphics card or with the screen, but only with the graphics driver.

• Re: Satellite L670 loses the wireless connection

  Hello

  I have a Satellite L670 - 1 H 1, a new laptop that runs Windows 7, with all the drivers and software uptodate, including the wireless card.

  I have a BT Home Hub 3 with an Edimax EW 7416APN v2 300 m range extender to help boost the signal in the kitchen area.

  The laptop works fine when I stay in the room where the reception centre. If I move in the kitchen the laptop will usually lose the wireless connection after a few minutes and I cannot get it back unless I turn the LAPTOP works and return to the Home Hub.

  I see no obvious reason to this problem. Two other laptop computers used in the home, more a smartphone stay connected with full signal in every corner of the House, at any time.

  I have to use the range extender, but is it possible that the laptop Toshiba just don't hear well with it?

  Any advice would be welcome.

  Thank you
  Canton

  Hello Canton

  As you know quality of connection WLAN depends on different factors is not easy to say why you have this problem, WLAN. I use Toshiba laptops for a long time now and I didn't notice in the past some serious question of WLAN.
  For example I'm 4 router with standard g and have very good signal even in the cellar too or out in the back yard.

  If possible, try to test the WLAN connection elsewhere. Maybe your friends have WLAN routers so you can test it.

  You have a new router or old?
  What WLAN standard do you use (b/g/n)?

• C4780 cannot find the wireless router

  I have a new iMac and old Toshiba that is running Windows XP and you use a Netgear wireless router.  When I got to the printer, it worked fine on the wireless network.  Bought a new router that I couldn't work with the Mac and the PC so I returned to my original router.  Now, the printer does not work as a wireless printer.  Summaries of diagnosis indicates that the printer cannot find the wireless router and fails under "Network Name (SSID) Found."  On the Network Setup page, my network is listed as a network discovered by the printer.  I guess there is a simple solution and hope to find the answers here.

  Thank you very much!

  Some printers C4780 left the factory with a default misconfiguration.  This could be the reason why you can not see the hpsetup network.  Here is an updated set of instructions for manually adding the C4780 to a Mac:

  Part 1 - Get the printer in Ad-Hoc Mode Wireless

  (1) turn on the printer.

  (2) display the printer has six keys; three on the left (top-left, middle left, below on the left) and three on the right (top-right, centre-right, bottom-right).  Press and release the following touch buttons in order:

  top left,

  bottom-left,

  top left,

  top left.

  (3) you should see the internal menu of printers.  Press the right button down to select 'Service Menu'.  Press OK (lower-left).

  4) press the lower button right until you see "Reset Menu".  Press OK (lower-left).

  5) press the lower button right until you see "half full".  Press OK (lower-left).

  (6) after a few seconds, the printer turns off.  Press the power button to turn on the printer.  It is now reset with the correct default network settings.

  (7) turn on the radio:

  Press the Scan button to get the wireless settings

  Select wireless Menu

  Select wireless settings

  Select Enable Wireless to turn on the radio.

  Part 2 - run the Wireless Setup Wizard

  The printer has now created an ad - hoc network called hpsetup.  To connect to this network on your Mac.

  Check the connection to the printer by opening the printer's internal web page.  You can do this by opening Safari, select bookmarks then ShowAll bookmarks.  On the left pane of Safari, select Hello and on the right, you should see your printer listed.  Double-click your printer and Safari should display the printer's internal web page.

  The printer Web page, select the network tab, and then select Wireless (802.11).  Now press Start the wizard to launch the wireless configuration wizard.

  When the wizard is finished, your computer unplug the printer's ad - hoc network as the printer reconfigures itself to connect to your network home.

  Reconnect your computer to your home network.  Verify that you can connect to the printer at the opening of its internal web page again once we were doing before.

  Finally, install the printer SW.  Since you have Snow Leopard, you don't need the CD that came with the printer.  Instead, open the Print & Fax under System Preferences applet and press the [+] button.  Highlight your printer and click Add.

• Satellite A110-294 does not recognize the wireless card

  Hello

  the question is:
  Why my Satellite A110-294 does not recognize the wireless card?

  I re - install Xp PRO with all the drivers.

  I have try all the drivers Wireless: Wlan intel + proset intel atheros wlan + wlesscmgr

  I don't understand, can you help me?

  Thank you
  André

  Hello

  To my knowledge, the A110-294 uses the Atheros WLan card and therefore the Atheros Wlan dirver should be the right one.

  You can find the latest driver for Atheros WLan here:
  http://APS2.toshiba-tro.de/WLAN/

  Just a question;
  You see the local network card in Device Manager? I mean, you should see an Ethernet controller or an unknown device in the network adapters
  The driver is missing, then the device must be marked with a yellow exclamation point

• Cannot set the time zone of Moscow winter + 3 hours.

  Cannot set the time zone of Moscow winter + 3 hours.
  Set the time zone Minsk 3 after the GPS clock moves forward 1 hour, timezone is set back from Moscow + 4.
  It is an error of your software when you are ready to address this issue.

  Automatic deactivation date & time(Settings>Date&Time...)

• Installed wireless Belkin, unable to see network, get error windows cannot configure this wireless connection and starting the WZC abuse

  Hello

  I have a belkin wireless router that worked on my primary computer and a portable computer for years.

  Recently, I moved my main computer and now it dosnt seem to work. Belkin is installed but when I ask to see available networks, it says that windows cannot configure this wireless connection and starting the WZC abuse. Belkin still works fine on my laptop so I know no there is not a problem here. Can someone help me please? I tried to type in %SystemRoot%\system32\services.mcs\s as with a question of people, but all I get is windows can't find this.

  Any ideas please?

  Thank you

  * original title - Help... problem with belkin wireless *.

  Let's see if I can cut through it.

  You wrote:

  Click the Wireless Networks (see this picture) - I did

  Is the box 'Use Windows to configure my wireless network' checked or unchecked? There is no such box.

  I connect using - he says belkin. another box saying this connection uses the following items. then underneath there are 3 tabs - install, uninstall and properties. If I press on properties it says name provider and in this box, it says windows index.

  It seems that you don't have not clicked the "Wireless networks" tab, after you open the properties of your wireless adapter.  From your description, you look at the 'Général' tab: click HERE to see the "Général" tab Click HERE to see the 'Wireless Networks' tab.

  There are 5 columns: name, description, status, startup type and log as.  The values for the last 3 columns should be started, automatic and Local System - on my screen there are 4 tabs at the top - general, connect you, recovery and dependency.

  You skipped a step... 5 columns are in the 'Services' window initial... you arrive at "4 tabs at the top", AFTER you double-click the Wireless Auto Configuration.

  Status of the service which includes 4 boxes. stop suspend and resume. the button highlighted in the start menu

  Just to the right of the expression "Service status", you should see a Word.  On your system, this word probably is "stopped."  The 4 buttons (boxes) are how to control the service.  Because you said that the highlighted button is 'start' which means that the service is currently stopped, and you will need to click on this button "start" to start.

  I strongly suspect that you had used the Belkin utility to control your adapter - and now, you also started WZC.  As I wrote above, you can have both running at the same time.

  When you click the icon of your "Belkin", do you have a screen that looks like this: http://www.wi-fiplanet.com/img/2006/belkinn1/08.jpg

  If so, you should return to the utility Services and 'Stop' the automatic configuration service.  If you want to use WZC instead of the Belkin utility, see http://en-us-support.belkin.com/app/answers/detail/a_id/40/related/1

  I'm not familiar with the Belkin Wireless networking utility, but many wifi manufacturer utilities can be used to turn your wifi on and off, then maybe your was off (the adapter on your computer - not the router).  If you identify the model of the card you have in your main computer, I'll see if I can find the manual on the Belkin website and maybe give you a little more information.

• Error message: "cannot find the wireless device" and not scan using 3 in 1 copy fax print HP 4500.

  Original title: Carpenter

  I can print but can't scan. Tried to uninstall then install the 3 in 1 copy fax printing hp 4500 but says cannot find the wireless device.

  Hi Ryan,

  You can check the link to HP support to run the HP Diagnostic Utility to check the issue of scanning:

  Find and fix common problems using tools of diagnosis HP printer=

  You can also check out the link to HP support and try to update the latest drivers/software for your printer:

  HP support

  You can also read the articles and check if it helps:

  Add or remove a scanner

  Scanning: Frequently asked questions

  The problems of scanning