Satellite L50 - B fan works even if the CPU load is very low

Similar Questions

• My Satellite A100 GPU fan works 100% all the time

  First: I have the Satellite A100-440 with GeForce Go 7300 and XP Professional (and Ubuntu).

  There is something wrong with thermal control. The first PC Wizard has always shown that the temperature of my GPU is "a very large number" and the fan is runnign 100% all the time (the main problem). Then I installed ATItool hoping he would show the temperature correctly. Well, it worked in part. Now when I check the temperature with PC Wizard, it indicates the temperature of the GPU normally (like 30-40 degrees celsius), but it also shows the GPU Diode temperature it's "a very large number" (as 4.294967E + 09 C) and the fan will operate at 100%.

  I tried to control fans with RivaTuner, but nothing happens.

  So if anyone has an idea how I could continue to solve the problem, I would be very grateful. I don't know if the problem is with the hardware (I could take this service) or with the software...

  Thank you!

  Post edited by: Avilja

  Hello

  Why are you talking about 'problem' and 'solve this problem?
  I see no problem!
  First of all I'm not all 3rd party applications that monitor temperatures. I'm not 100% sure if these applications provide a good values.

  However, as far as I know the laptop was shipped with Vista and not XP and Linux. You do not use a factory settings. It seems that you have set up the laptop with new applications and you should know that all the software installed and running insists on the CPU and other parts.

  BIOS fan table supports different temperature and cooling of the speed measurements. This means that if the temperature rises to a higher level, the cooling module starts and tries to decreases the internal temperature.

  Usually the temperature depends on the use of the laptop. If several processes of the OS are running in the background, that the CPU performance are high, the temperature rises and the fans start to run. There is nothing unusual about it.

  Furthermore, the dust and debris inside the laptop might have a bad influence on the laptop cooling. From time to time, it is advisable to clean the cooling modules.

  Last but not least the laptop must be placed free on table to ensure the circulation of air correctly. Don't forget that there is enough free space around the laptop.

  Finally, I must say that one of my friends has an A100 and the fans run correctly.
  This means that the cooling modules works with maximum performance while playing games or using graphics software.
  However fans do not work with maximum performance using only common programs like IE software or office.

  Good bye

• Until the latest update when the AutoComplete bar has been selected, he "went" no other by clicking. I must now click the refresh arrow. It won't work even with the return. How can I operate the old way easier?

  Until the latest update when the url I wanted in the address bar of AutoComplete has been selected, it "accompanies" no more further by clicking on. I must now click the refresh arrow. It won't work even with the return. How can I operate the old way easier?

  You can disable this extension in tools > Modules > Extensions and close and restart Firefox normally.

• Tecra Z50 A-h-13 - fan works half of the time

  Hello

  I got a new Tecra Z50 A-h-13 (i5, 8 GB RAM).

  Although the processor is underemployed (approx. 20% of capacity), the fan works half of the time!

  When the fan is running the Toshiba PC Health Monitor shows approximately 44% CPU temp. and 36% system temp.

  When the fan works not the Toshiba PC Health Monitor shows similar values!

  What is it good for?

  In my opinion, the fan is not alone. I have not found a possibility to adjust the speed of the fan (PC Health Monitor always shows 45%) or the starting temperature. The current Version of BIOS is installed.

  Is it possible to get a SMART fan control?

  Best regards

  Zvonko

  Hello

  The manual fan control is very limited.
  What you can do is to change some parameters in the Windows power options.
  Go to the control panel? power options
  Select the power plan you use.
  Then choose Advanced settings.

  In the advanced power settings, you will find the option method Cooing and the performance of the processor.
  I recommend you degrade the performance of the max processor at 90-95% and to change the method of passive cooling (both for the battery and plugged)

• Satellite C55-A-1RV cooling fan is placed on the CPU?

  I have a Satellite C55-A-1RV model and I want to know if this machine have a fan on the processor...

  Thank you

  Of course, there is a Silent fan cooling which cool the CPU.

  This cooling module is one of the essential elements for laptop... the thermal grease is placed between the fan and processor and without such cooling CPU module overheats

• I bought Halo 2 for Vista, but who like OS Windows XP Pro, just can't launch the startup.exe, I search the community, there is a rumor that it won't work even with the patch. Can someone help, please?

  I bought Halo 2 for Vista, but who like OS Windows XP Pro, just can't launch the startup.exe, I search the community, there is a rumor that it won't work even with the patch. Can someone help, please?

  Unfortunately, Halo 2 does support Windows Vista and more.  Windows XP is not supported.  There may be 3 party hacks that can make it work, but they are not taken in charge and potentially dangerous.

  Paul Smith - MVP for Windows desktop experience... I crawled off NNTP - for now. Detachment Aldershot, United Kingdom. On the internet at windowsresource.net and dasmirnov.net. Please post back to let us know what works and what does not. :-)

• How can I make sure my internet cable works even if the icon is not displayed by the clock

  I see the wireless connection icon, but I used to see one for the wired connection also. So where is it?

  How can I make sure my internet cable works even if the icon is not displayed by the clock?

  Click Start > Control Panel > network and Internet > network connections.

  Click with the right button on your Local network, and select Properties. In the window properties of LAN make you that these boxes are checked.

  [] Display the icon in the Notification area when connected

  [] Notify me when this connection is limited or no connectivity.

  Click [OK] and get out of here!

  Right-click on start and select Properties. On the taskbar and Start Menu click the taskbar tab, and then click the Customize in front of the Hide icon button inactive and it make sure that the option 'always show' for the local network is selected.

  HTH,

  NASS - http://www.nasstec.co.uk

• My optical mouse 3000 does not work even if the red light is on in the background

  My optical mouse 3000 does not work even if the red light is on in the background

  Hi Russell,

  Thank you to contact Microsoft Community and we will be happy to help you with your concern.

  According to the description, it looks like you are facing a problem with the optical mouse 3000.

  It would be great if you could answer these questions to help you further.

  1. have you made changes on the computer before this problem?

  2. you receive an error message or error code?
  3 is confined with any specific application?

  I suggest you to see the steps in the following Microsoft article.

  
  Mouse, touchpad and keyboard under Windows problems: http://windows.microsoft.com/en-US/windows/help/mouse-touchpad-and-keyboard-problems-in-windows

  Troubleshoot the incidents of the response to the mouse or wireless keyboard: http://support.microsoft.com/kb/838398

  Troubleshoot a wireless mouse that does not correctly: http://support.microsoft.com/kb/321122

  We would be more than happy to help you if the steps above did not solve the problem.

• My touchpad lock does not work, even if the orange light is on, indicating locked buffer. Probook4420s.

  My touchpad lock does not work, even if the orange light is on, indicating locked buffer. Probook4420s.  Windows 7 32 bit.

  Hello

  If the amber light is on the TouchPad itself, try double tapping

  If that is not activate, try uninstalling the device driver course Synaptics pointing, then restart the computer and download and install the driver from the link below.

  http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=321957&prodSeriesId=4145435&prodNameId=4145436&swEnvOID=4052&swLang=13&mode=2&taskId=135&swItem=ob-86824-1

  Kind regards

  DP - K

• After updating my iPhone 6 (9.3.4) the WiFi signal becomes very low! I did everything, but the problem does not stop! I don't a not update my other devices & their very good WiFi signals. Please help me solve this terrible problem...

  After updating my iPhone 6 (9.3.4) the WiFi signal becomes very low! I did everything, but the problem does not stop! I don't a not update my other devices & their very good WiFi signals. Please help me solve this terrible problem...

  Here's a tip for the user on the problems of Wi - Fi. Suggest from the top and bottom. Maybe one of them will help you.

  (1) restart you device.

  (2) resetting the network settings: settings > general > reset > reset network settings. Join the network again.

  (3) reboot router/Modem: unplug power for 2 minutes and reconnect. Update the Firmware on the router (support Web site of the manufacturer for a new FW check). Also try different bands (2.4 GHz and 5 GHz) and different bandwidths (recommended for 2.4 to 20 MHz bandwidth). Channels 1, 6 or 11 are recommended for 2.4 band.

  (4) change of Google DNS: settings > Wi - Fi > click the network, delete all the numbers under DNS and enter 8.8.8.8 or otherwise 8.8.4.4

  (5) disable the prioritization of device on the router if this feature is available. Also turn off all apps to VPN and retest the Wi - Fi.

  (6) determine if other wireless network devices work well (other iOS devices, Mac, PC).

  (7) try the device on another network, i.e., neighbors, the public coffee house, etc.

  (8) backup and restore the device using iTunes. Try to restore as New first and test it. If ok try to restore the backup (the backup may be corrupted).

  https://support.Apple.com/en-us/HT201252

  (9) go to the Apple store for the evaluation of the material. The Wi - Fi chip or the antenna could be faulty.

  Council: https://discussions.apple.com/docs/DOC-9892

• SG - 500 - OID SNMP to lower the CPU load?

  Hello

  I have several SG500 (autonomous and stacked). How can I get the CPU via SNMP load? Who knows the correct SNMP OID to lower the CPU load?

  In the MIB that are provided for download one was not able to find the correct OID.

  Hello

  There are three OID for the CPU usage:

  CPU utilization for 5 seconds	. 1.3.6.1.4.1.9.6.1.101.1.7.0
  CPU utilization for 1 minutes	. 1.3.6.1.4.1.9.6.1.101.1.8.0
  CPU utilization for 5 minutes	. 1.3.6.1.4.1.9.6.1.101.1.9.0

  This came a note of junk, I got in an email, so I don't know exactly where this information is originally.

  Let me know if it works for you,

  Christopher Ebert - Network Support Engineer

  Cisco Small Business Support Center

  * Please note the useful messages *.

• The volume of the recorded sound is very low when played. I tried to solve the problems through Control Panel of configuration-sound options and increased the volume to 100 form my mic too. All the other volume options, it's 100 too. It has no effect. Hel

  The volume of the recorded sound is very low when played. I tried to solve the problems through Control Panel of configuration-sound options and increased the volume to 100 form my mic too. All the other volume options, it's 100 too. It has no effect. Help needed ASAP

  Hello

  Control Panel - SOUNDS - Audio peripheral devices configuration-manager

  Make sure you write down the description and model double click top - tab drivers - write version. Now
  Click on update drivers who cannot do anything like MS is far behind the certification of drivers. Then RIGHT
  CLICK above and UNINSTALL - REBOOT - this will rebuild the driver stack.

  If your driver shows 06 you have the default windows and part of the question.

  Go to the system manufacturer's website and get the latest Audio/Sound drivers - download - SAVE - go to the place where you
  Put them - right click on Reboot - RUN AS ADMIN -.

  Check the Version on the tab of the driver in the device as a sound Manager often restoring drivers, then install
  the current version. Restart and check after each try, not uncommon to have to run the pilot of 1 to 4 times or more.
  Just make sure that the version you have installed appears in the tab of the driver.

  Then navigate to the site of the manufacturer of the device and search for the drivers more recent and repeat the installation procedure.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  ---------------------------------------------------------

  After the updated driver.

  Click with the right button on the speaker near clock - recorders - right click in the box - check show disconnected devices
  and show disabled devices - check your micro - highlight them, then lower right properties. Do
  of course the appropriate injector is enabled and check that other settings - on the levels tab make sure MUTE is not checked
  and APPLY / OK changes.

  Also in the search for some Audio Manager Panel (perhaps named after the manufacturer of the sound driver). Mine
  is the RealTek Audio Manager, yours can be quite different name if you have one.

  How to activate Audio devices hidden in Vista
  http://www.Vistax64.com/tutorials/143447-audio-device-enable-hidden-devices.html

  Connect one microphone, music player or other audio device to your computer
  http://windowshelp.Microsoft.com/Windows/en-us/help/b0e3d7fb-1b4a-4926-8254-65da289209261033.mspx

  Problems with sound and audio or no sound - a Mr Fixit
  http://support.Microsoft.com/GP/NO_SOUND

  I hope this helps.

  Rob - bicycle - Mark Twain said it is good.

• When I open my application on my Macbook pro using bootcamp, the photoshop CS3 opens very low.  How can I solve this problem?

  When I open my application on my Macbook pro using bootcamp, the photoshop CS3 opens very low.  How can I solve this problem?

  Legacy versions do not support the higher resolutions / poster of the retina. Refer to this:

  My UI elements appear tiny. | Error postal codes of Mylenium

  Mylenium

• Satellite A500-138 - lighting buttons does not work even in the BIOS

  Hello.

  I'm just curious to know if anyone else has a problem with the (play/pause excatly) multimedia keyboard backlight? Mine died today, and there is nothing I can do to make it work again.

  The key still works, but when I turn on the backlight, backlight on everyone, but the play/pause (the backlight of the other keys work, touchpad and Satellite logo too).

  I use Windows 7, but the problem persists even in the BIOS.

  I think the backlight of the button is just dead.

  I have to admit I'm really disappointed with this laptop. Config is great, design and are also involved, but I can just take the couine noise that makes C2D (RMClock, one utility, I know that to solve this problem, does not recognize the A500 motherboard) and the fan almost never works to 70%, and now that the backlight...

  If the backlight of the multimedia key stops working after 3 weeks of use, which will be in the future? It's too scary to think ;)

  I was really excited by Toshiba, but day after day I come to the conclusion, that it is the first and the last laptop that I bought at Toshiba - never had similar problems on other laptops, same nonames.

  Of course, I know that I can has sent for fix, I guarantee (and wait about a month to get a backlight fixed stupid). But why hell not the backlight stoped working, if LEDs vitality is long as hell? It can mean two things: I really don't have a chance, or Toshiba did not pay too much attention to detail during production A500s. And after 3 weeks of use, I fear that the second option is much more likely...

  Then, someone has a feeling similar to this topic? And someone has a problem with backlight?

  Hello

  He damage of s to hear that your light has stopped working, but I think that it s just a software problem.
  I have a Satellite A500 equipped with buttons of enlightenment and everything works great with Vista and XP I m very satisfied.
  Unfortunately until that yet I didn't test with Win 7.

  I doubt you want to send this laptop for ASP, as I said, there seems to be a software problem and you can find it easily
  You must set the notebook to factory settings I mean that you must use the recovery disc in order to get the same State as on the first day of purchase

  Moreover, I visited the European driver of Toshiba page and, unfortunately, I didn't see no Win 7 drivers for this series at this time
  I guess that Windows 7 drivers will be released in the near future.
  So I wonder how you came to the button illumination because this feature requires the Toshiba driver and tools as well as the drivers aren't there?  :|

• Satellite A50 - 109 fan works not properly after the HD upgrade

  Yesterday, I upgraded the HD of my laptop A50-109 of 3 months. The original HD installed in the laptop was (to my surprise) a Fujitsu HD 40 GB 4200 RPM 2 MB cache.

  So I've upgraded to a Toshiba 80 GB 5400 RPM 16 MB of cache and had to re - install Windows XP Pro and all the drivers of toshiba.

  Now, since the upgrade, the fan is constantly working even when CPU power, cooling method and all the others are on the lowest setting possible. Before the upgrade, the fan would obey the parameter of cooling method and the fan would be COMPLETELY silent, IE does not work because there was minimal use of the CPU, etc.

  Now the situation has changed, and the fan runs constantly no matter what use. I am terribly disturbed by noises, and I see no reason for the change.

  Is there a solution or should I return the HD or laptop?

  Hi Simon,.

  A very interesting discovery.

  Kind regards