Satellite L50 - USB connectivity problem

Hello, new to these forums and just buy a Toshiba Satellite L50.

The problem is when I connect my iPhone in a few seconds it will disconnect, reconnect, disconnect plug. Then a pop up according to sleep and fresh loan, then another pop up will say choose what to do with this device, and then it will disconnect and reconnect etc. and loop messages and connection.

I disabled sleep and even cool thing. I allow it and put the laptop to sleep and I can charge my phone and it is not disconnect and reconnect.

For the moment, I turned off the iPhone into Device Manager and its load although if I try and allow him to do as stated above.

It is not a problem of windows I Linux out there, and it will do the same to connect/disconnect. "Buzz-buzz" vibrating door very quickly.

It is not the phone or cable as these work well on another computer.

So can anyone explain what this problem and how to fix it.

Footnote: BIOS Version 1.90

Thank you!

Hello

As far as I know the laptop supports different USB ports.

Have you tried to connect the smartphone on different USB ports?
If this isn't it.

More I recommend you to check the parameters of each device to save energy.

In-> controller device manager USB-> properties-> last tab (power management)

Here you will find an option to turn off the device to save power.
This option should not be enabled. In the event that the option is checked, remove the mark.

Tags: Toshiba

Similar Questions

  • Toshiba Satellite L50 - Wireless / WLan problems

    I bought Toshiba Satellite L50.

    I really bard WIFI reception - good now I sat 2 meters between the router and I have only 2-3 bars.
    If I am to 7 meters away, I have no reception at all.

    There is no problem with the router, I checked with other devices (phones, laptops).

    When I'm with a direct access to the internet with internet LAN cable is always at maximum speed.

    I made sure that I have the most up-to-date drivers for my network card.

    How can I solve this?

    No one can help?

  • Install HP Officejet 5740 & USB connection problems

    I recently bought a HP all-in-one OfficeJet 5740 printer for my desktop Dell XPS 8700-(Windows 8.1) and attempted to install, using the USB connection option. I was informed by the instructions of configuration to go online to a Dell website for the latest version of the installation software to download if I had access to the internet. I have DL'ed software and it apparently installed OK-(aucune erreur ou quoi que ce soit pour indiquer qu'il n'a pas abouti). Once finished with the installation of the software, I got to the window option connection-(wireless, usb cable ethernet cable). I chose the option of usb cable, however after having to then connect the USB cable to the printer and the computer via the usb cable, it tries to connect, but alerted me, stating; "Failed connection to printer, printer was not able to connect successfully via the usb cable. I tried this several times-(par moi-même et remote assist avec Support ordinateur Dell). I had the same problem last week when he tried with my old HP Officejet 6100, which I wanted to replace. I ran the program of doctor printing/scanning HP on the 5740 and it lists the printer and the software installed, however the HP printer install lists assistant the complete software package for the printer is not installed and some basic features drivers may be missing or damaged. Also when I go into Control Panel, then devices/printers, it displays the icon of 5740, however after rt - by clicking on the printer icon, instead of the regular menu that comes up to the top-(showing the complete properties, select this printer as the default printer, etc.), it displays a menu of smaller selections very-little (who don't understand not the "select as default printer"). I tried downloading the printer software two ways-(via the HP website on line 1, and then click the installation CD supplied with the printer, the same results. The printer was purchased 11/15/2014 and seems works very well-(tirages test-page, page d'alignement, etc.), but I can't print anything, and apparently it can not connect via the USB-(* j'ai acheté un nouveau câble usb 2.0 hier et, utilisé pour écarter la possibilité d'avoir un mauvais câble). My Dell computer is only 10 months old, and I upgraded to 8.1 Windows back on 25 October.  The USB ports on the computer all seem to work properly when connected to another USB device other than the 5740 printer.  What is the software apparently is not fully installed, with some missing drivers or, possibly, USB drivers should be updated? Any help would be appreciated. Thank you!!!

    Thanks for responding, but I was able to get the printer installed with the help of diagnostic, remotely in line with my computer manufacturer support staff. He was determined to be a software problem because of a recent update of Windows 8.1. Thanks for the effort!

  • WRT160NL connection with n and USB connection problem

    Hi guys,.

    I have the Linksys WRT160NL router and I have two fundamental problems with that:

    1. I have a laptop HP with n on its wireless card connection. (it's an HP probook 4720 s). So I know that this laptop has ability. n I have the most recent driver vor he 3.1.18. The thing is that my Linksys router does not transmit sound wireless n, just g...

    What should I do to make it work with n as well?

    2. the second issue is that the USB connection is working in a very strange way. I have attached an ADATA with USB 3.0 HDD external, even. He works in 2.0.

    I have a lot of WAV files on it and when I stream to my receiver files pay with much intrerupptions, break ups. MP3 work very well.

    I don't know what to do to solve this 2 problems... Maybe someone could help me...

    Thank you

    Try changing some settings on the router wireless.

    Connect the computer to the router with the Ethernet cable. Open the router configuration page. Go to the wireless tab and the manual value configuration view. Change the channel to 11 wireless. Make sure that the network is set to mixed. Save the settings.

    Go to wireless security sub tab and change the wireless WPA2 with AES security mode. Save the settings.

    Click the tab under advanced wireless settings change the tag to 75 interval, RTS threshold and fragmentation to 2304. Save the settings. Now try to connect to the network again.

  • USB connection problem

    Whenever I connect my tab to any PC or laptop using the USB cable, it is not connect. It is not pop window on the USB connection. USB port works fine. Tab gets charged through this property. Functional disorder it is. Everyone will solve it?

    Hello and welcome to the HP support community!

    Need a few details.

    What tablet you are asking about?

    What OS is on your PC?

    Tried another cable?

    Usual suggestion is to unplug the devices and reboot the computer and tablet.  Check the settings of the tablet in storage/settings / < icon options, top right - looks like 3 blocks stacked vertically > / USB connection to the computer.

    See if the PSG is checked.  It is suitable for the transfer of all types of files.  Connect the devices.  If still no joy, try to uncheck MTP and PTP.  This should make the Tablet appear as a camera.

    I had to do with an old Win XP computer so that he can "wake up" and make the connection.  I then switched to the PSG and all was good!

    WyreNut

  • Satellite C660D - 10 p - USB connect problem Windows 7 64 bit

    Hello!

    USB drive is no longer recognized shortly after the start.

    According to 'Unsubscribe' or 'Edit user' still OK, but even for a short period.

    Have no USB Updat to Toshiba, a controller failure will probably be.

    Can anyone help?

    Harald greetings

    Hi Harald

    Can you please tell us what model of laptop do you have?
    Are you using the original version of OS that you got with your laptop?

    Maybe I didn't understand the description of your problem, but I imagine that the USB ports do not work on your laptop satellite? Right? have you tested with different USB devices?
    When you open Device Manager you will see some unknown devices here or some hardware issues?

  • HDMI / projector with Satellite L50-B-2FN problem

    Hello!

    HDMI / projector with my brand new Toshiba problem.

    My computer laptop hdmi works fine with my tv Samsung, no problem. I simply press F4 and select how I want my second screen action on my tv.
    But when I connect my laptop to my Optoma HD67 projector I have no picture but sound works.

    I can see in the portable computers Panel for program HD-chart that Optoma is found as a second screen feature and is named: digital TV Optoma 04 3.

    But there is no way to make it work. And I tried all the settings available for the second screen (my OptomaHD67). One is the refresh rate which contains the following values: 60/59/50/30/29/25/24 and 23 Hz p. When to choose between 30 to 23p Hz Optoma said popupscreen found but shows only a blinking screen! What we call the war of ants here in Sweden.
    By choosing from 60 to 50 Hz p, nothing happens.

    If I chose VGA projector works whit my laptop, but I want it to work with HDMI!

    Yes, I have havetested different hdmi cables and right know I use the cable that works with my Samsung tv. Not a problem of hdmi cable.

    My Toshiba:
    L50-B-2FN satellite / (PSKTGE-O2POOQN5) / Intel Core i7-5500U /CPU2, 4 GHz / Intel HD Graphics 5500 / Win 8.1 (x 64)

    My Optoma HD67SpecificationsHighlights
    HD Ready
    720 p (1280 x 720)
    Contrast
    4000: 1 (with Image HAVE)
    ANSI contrast
    400: 1
    Audible noise
    mode Standard 29dB
    Brightness
    1800 lumens
    Connections
    Video compatibility
    1080 p 60/50/24, 1080i60/50 720 p 60/50, PAL,.
    NTSC, SECAM

    For advice or assistance would make my day! :))

    As I see your validation on your laptop computer HDMI port works perfectly.
    In my opinion, you should contact Optoma support and ask for help.
    Maybe they can help you with that. I mean they know product clean and I don't know there is some thing that must be done and video input on your projector turned on.

  • Satellite T110 - Bluetooth connection problem

    Hello

    You just buy a Satellite T110, running on Windows 7 and have open Bluetooth it downloaded drivers.
    It can detect my N97 phone by using the "Add new connection" Wizard in the Bluetooth settings but Manager then displays an error "the service Detection failed.

    It fails also when I click on something to send by Bluetooth via wireless file transfer option, he can see my camera, but I get the error 'discovery of Service failed.

    I'm doing something wrong?
    Any help would be appreciated.

    See you soon,.
    A >

    Hello

    Just a quick question: have you tried to reinstall the Bluetooth driver?

    I had a similar problem with my cell phone. I could solve the problem after checking the Bluetooth settings. Only, I chose another port.

    Good bye

  • Satellite P300D - wireless connection problems

    Good evening.

    Sorry for my bad English.

    Here's my problem: whenever I try to install my wireless modem, my computer shuts down, the blue screen before connecting off the coast with many words that I did not have time to read.

    The modem is certainly not a problem, as I tried it on another PC and it works perfectly fine.
    Can you help me?

    Hello

    If I understand correctly your problem; the BSOD (blue screen of death) appears during the installation of the software for the external Wlan modem immediately.
    Right?

    I assume you are using portable satellite P300D Win 7 on your computer.
    There may be a compatibility problem with Win 7 OS?

    > The modem is certainly not a problem, as I tried it on another PC and it works perfectly fine.
    Have you tested the modem with the other Win 7 computer?

    The other hand the Mobile supports an internal Wlan card.
    Have you tried an update of the Wlan card driver?
    To do this
    Here you will find the latest drivers:
    http://APS2.toshiba-tro.de/WLAN/

  • Satellite A200 - network connection problem

    My Satellite A200 struggled to connect to my wireless network.

    It detects the network, but then when I opened the networking and sharing service - it comes up with an error message - "the dependency service or group could start.
    I understand that it is the network location awareness service which does not
    Then he gives me a message saying that I should check my system event log, or are looking for the servoce error code: 1073741288
    Help, please!

    :)

    It is more a problem of Microsoft.

    Google search for "the dependency service or group could start.

    There are a lot of results, for example (http://answers.yahoo.com/question/index?qid=20080215035316AAStYGP):

    * Go to start > run and type services.msc, and then press ENTER.
    * Look for diagnostic and defined policy on Auto Service
    * Wise restart the service too.

  • WLan Satellite P100 - 105L connection problems:

    I have the following problem.

    Satellite P100-105 notes, with XP home. All drivers up to date, connection via WiFi.
    When I connect to the internet using IE7, IE6, Mozilla, Opera a few times I just message "waiting for response from...» "in the status bar and the page not to load not.
    If I update its ok, or to certain pages it won't work even if I update (usually on the typo 3 saving a document).

    1. I have no virus, no Trojan.
    2. try with IE without addons, allso with IE when I was in "safe mode" XP.
    3 downloaded the latest WIFI drivers, latest version of the bios.
    4. when I try on other notes of toshiba, another model with win vista on IE7, it works normally. Allso when I download huge files, its ok.
    5. do you have legal and up to date windows XP with Service Pack 2

    so, I can say 4 things:
    1. it's not caused by signal,
    2. his sweet independent navigation.
    3. it may not be caused by HW error, if he would, large downloads/uploads will fail
    4 any other software, it is stored in the normal state, its not the cause.

    SOMEONE HELPPP

    sound very, very boring.

    > When I connect to the internet using IE7, IE6, Mozilla, Opera, a few times I just message "waiting for response from...» "in the status bar, and the page does not load.

    You said sometimes? So I guess he can't every time while you use the WiFi network.

    > 4. When I try it on other notes of Toshiba, another model with win vista on IE7, it works normally. Also when I download huge files, its ok.
    The two laptops use the same WLan card? If this is while there may be a compatibility problem between the router and the wireless network card

    But generally it is not easy to say what could be the problem. Have you checked the same message is displayed using the LAN cable?
    Check it!

  • Win 7 USB connection problem disconnect/connect Cycl

    Is anyone else having problems with their Droid Turbo and a Win7 PC connection? I got my first camera at the end of November. When I initially plugged on my PC, the AutoPlay of Windows kept popping up window and the device would be cycle as if it had been disconnected. The AutoPlay window closes never alone, and I need to close from a few to several 10s of windows (based on how long I left it plugged in).

    I was able to get a stable connection after installing the Motorola Device Manager software.

    After a problem without report, Verizon has replaced the original phone with a new phone. The new phone is the same cycle of disconnection/reconnection anytime it is plugged. Software Motorola device Managger says that the software is up to date.

    I connected the phone to a Linux computer and had no problem copying files back. The connection is remained established until I got the USB cable.

    I rebooted the phone and the PC several times that I care to count.

    Also has anyone seen this problem? More importanly, does anyone have a solution?

    My phone (in MTP mode, without debugging) shows that the VIDID 22 b 8: 2ea4. On several occasions, I saw the PID also be 2ea5 and 2ea8. (Maybe it's with debugging on, perhaps a PTP mode).

    A few times, the device is presented as "Unknown device" with no details in the Device Manager.

    I plugged the phone in each USB port on the computer.

    If I knew that the files to remove from Windows to replace the driver I'd do it. If I knew that the right driver I tell Windows to use. So far I have not found one that works.

    Thank you

    James

    James best would be to connect the device in MTP, USB OFF debug mode. In Device Manager, locate the device and click on uninstall. At the prompt to uninstall to make sure that you CHECK DELETE the driver software. Uninstall device of motorcycle, bike mobility Manager drivers and nothing of another "bike Mobility" brand. I use a disc cleaner (ccleaner) delete left over remnants of uninstalled product files. I first do a system cache/clean and repeat several times until the cache gets up, nothing to remove. After that it's over, I run the registry cleaner. After scanning, select "Questions of difficulty" to the quick click reg backup YES, choose a SAFE place 'FIX ALL '. Once done, repeat until there are no more problems found. After all this is finished, STOP, do not restart. Computer to start up, run CCleaner again just to make sure everything is clean, so before you plug in your phone, go to and install Motorola Device Manager/USB Drivers. Let the full install and reboot. In developer options, revoke the authorization of debugging. Connect the phone in MTP mode to the PC and let Win7 to install the drivers. Change the connection of the device to PTP repeat, then finally change device USB debugging and let windows install the drivers. Let us know if this helped or hurt.

  • 1208fs for labview 10 usb connection problems

    Hello
    I'm relatively new to Labview and just improved labview 10. I used 6.1 before and had no problems using my mcc Board of 1208fs USB to run experiences before. I tried to connect even to labview 10 on my new computer, and the only thing that will connect to the instacal is. Ive plugged throu instacal, but is not visible in the list of I/O that selects the channel to use. Any help would be appreciated.

    Thank you!
    Andrew

    By the way, my os is windows xp

    Andrew,

    MCC daq devices have a different set of drivers for LabVIEW 8.2.1 LV versions and newer.  See http://www.mccdaq.com/daq-software/universal-library-extensions-lv.aspx this is ULx.

    I have one of the devices USB-1208 and discovered very recently this issue when I wanted to use it in a LV 8.5 application I wrote.  The new driver is actually nicer and DAQmx drivers a little resembles the way you use them.  While the former pilots of the Universal Library for older versions of LabVIEW looked like using traditional DAQ hardware drivers of OR.

  • HP 1515: Deskjet Ink Advantage 1515 USB connection problem win10

    I bought yesterday hp1515.and the many ways as stuck in connection.i tried usb configuration (disable startup all the apps, buy a new gold usb sales-man who gave me), but still nothing is happening...

    now what?

    I solved the problem on my own... windows 10 prefer HP DESKJET 1510 SERIES DRIVER that does not work.

    you have to manually put HP DESKJET 1510 SERIES DRIVER CLASS to work

  • USB connection problems

    I was not able to get my wife or my new Crush phones to connect as a USB for windows xp. It does not charge via USB, but never it presents itself as a drive in windows Explorer.

    I tried with her on the modem and mass storage in the settings on the phone. No noticeable difference.

    It has a micro sd if any installed card what counts.

    I noticed a few other oddities that I'll put in separate threads.

    First message mentioned "mass storage parameter" did not appear because of the issue?

    Now is to "modem mode"?

    Will need to check that it is in "mass storage" for the memory and USB to work together.

    Might need to reformat the chip or try another brand chip... chip could be bad?

    With the help of / are you moving the same chip between phones?

    In the last post, you have a double problem... even in both phones.

    Did you use the USB cable supplied with the phones.

    Have you tried another cable, try the other Crush phones USB cable?

    I have another USB cable provided with another device (a camera) that fits, and it doesn't work right, or the cable may be bad or the crush USB cable may be devoted to this type of phone.

    When the phone off, made the show telephone the charging green screen when pluged in the USB port of a computer is turned on... If the computer is off, no power on the USB port.

    My wife and I have the crowds without any problem,

Maybe you are looking for

  • Problem with El Captain (5.1.7 server) and the management of permissions

    Hello world I have a big problem with our Mac Mini Server (El Captain) and the server program. In recent weeks, the server didn't give the permissions of a folder. for example: Mr. X had permission to read and write to a folder.Mr Y too. Mr. X has cr

  • Cannot make a payment with the new Firefox. Works in Internet Explorer.

    Try to make payments on an https site and is no longer functions after upgrade to Firefox. Had to resort to make payment through IE. Memory cleared cache, restarted, etc has no effect. No messages pop up, connection is good, just, it does not allow p

  • Security 0176 - the system has been tampered with

    The machine is therefore a T40. He had no no password for at least the 2 years ive had it. The main battery was bad and the cmos battery died recently (id assume bad main battery helped along). After replacing the cmos battery (tested with v-meter an

  • error message: "WINDOWS\system32\rundll.exe is not found."

    WINDOWS\system32\rundll.exe cannot be found please check the root etc... etc... I've tried everything here.  How do I just uninstall WINDOWS and then reinstall it? I tried ALL of the suggestions I found here.  It is not in my Cache file, either this

  • Keep the connection information

    A couple of weeks my computer has stopped keeping email and logon information.  Even if I click on the "Save my login" box, the next time I turn on the computer the information has disappeared and I have to repeat the process. How can I solve this pr