Satellite L505-13Z - BOOT error

Similar Questions

• Satellite L505 - 10K - unexpected error when using recovery disc creator

  Toshiba Satellite L505 - 10 k

  Can't do any recovery disk when I open the toshiba recovery media creator, it says: an unexpected error has occurred. Close the program and then restart it (error code: 0D00F6-49-00000015) and then I click ok and then, it is once again and then I click ok and it is once again and I click ok and then the program comes and when I create the disc it comes to audit, but then it says: cannot read the following file. E:------Boot-fonts-chs_boot.ttf (error code: 02015-20-00000000).

  I really need help, I'm afraid something will happen to my computer, so is there someone who knows something about this kind of problem?

  Grateful for your help.

  Hi putte32,

  To be honest I never received this error before but it sounds like that recovery creator disc doesn t work properly... You should try a HDD recovery to restore the factory settings. Maybe you are able to create the recovery disk.

  Otherwise, I would contact an authorized service provider. If you can t create the recovery disk, the guy should be able to help you to complete this procedure.

• Satellite L505-13Z - unable to repair Windows

  Hello

  It's been a while since I reinstalled Windows on my computer (2.5 yr old L505-13Z), and in my view, it is now necessary because the computer is running a little heavier that it was after the last restart. I also upgraded my ram from 4 GB to 8 GB with the same specifications as the old RAM last week (it is well recognized by Windows and caused no problems during installation).

  I tried to recover windows with utility recovery disk without success. I turned on the computer while maintaining the '0' key and Windows just started normally with no unusual response and no commissioning recovery utility. I checked the folder of HARD disk recovery and it seems to be intact.

  I tried to do the same with F12 then "repair my computer". Then, I was invited to insert the recovery DVD, and then restart the computer. The following messages appeared with her: "cannot start Windows. A recent hardware or software change might be the cause. "Status: 0X000000e info: the boot selection failed because a registered device is inaccessible.

  When I tried to install windows with my DVD (I installed Windows with these DVD before so they are supposed to work) recovery, I just receive a constant '_' symbol in the upper left corner of the screen and no progression until I have ejected the DVD, then Windows started normally. I tried to play music CD s on the DVD player and they worked so I guess there is no problem with the drive.

  Anyone know what could be the cause? Is there a solution in addition to take it to the service? It is not in warranty more so I would avoid her.

  Thanks in advance for any help.

  Stand by.
  Let's start talking step by step, because the history is somewhat confusing.

  Firs let us clarify HARD drive recovery facility.
  Please check Toshiba document - http://aps2.toshiba-tro.de/kb0/HTD1303440001R01.htm and let us know what happening exactly when you follow the recovery HARD drive installation procedure. On what stage you noticed the problem?

  Try also the follow-up:
  Start your laptop and press F12 for the Boot Manager. When the list of all bootable devices appear put recovery DVD into the optical disc drive, has chosen the CD/DVD drive and press ENTER.
  What happens when you do this?

• Satellite L505-13W shows error blue screen

  My error on blue screen shows computer laptop SATELLITE L505-13W.
  The operating system is started and after some time, it shows a blue screen error and restarts.

  Even after repair successful when restarting requested repair, he showed the same error.
  So I tried to recover with the recovery cd, but it turned out to be a tragedy.

  He eraced my complete HDD to stone age and smiled saying recovery is not possible.

  Please help me...

  Hello

  If the laptop can not be recovered using the recovery disc, then it feels the hardware problem.
  Are you sure that your recovery disc is OK?
  Have you tried to install the OS using another installation disc?

  Perhaps it would be useful to check if the problem could be related to defective recovery disk, but if the BSOD (blue screen of death) appeared before the installation of the OS, I would say that the problem can be caused by an internal hardware malfunction

  It would be necessary to check the modules of RAM and HARD drive.
  HARD drive can be verified by using the diagnostic software from disk as Drive Fitness Test (freeware)

  RAM could be checked with a tool like memtest, but you need a system to market, then in this case, you can not check the RAM using a software that I recommend to remove a module and test the laptop using a module in each slot

• The laptop recovery Toshiba Satellite L505-S5997 problem error: Windows cannot verify the digital signature for the drivers required for this device

  I have a Toshiba Satellite L505-S5997 computer laptop and my hardrive recently crushed, impossible to restart.  I installed a SEAGATE 500 GB/sata/GO 16 MB of Cache, 7200 RPM hard drive. I ordered recovery for the computer disks and many of the drivers will not update or install without error that tells me that "Windows cannot verify the digital signature for the drivers required for this device. A recent hardware or software change might be installed a file that is signed incorrectly or damaged, or maybe it's a malicious software from an unknown source. (Code 52) "error.  Also, when I try to update Windows 7 I get the ' Windows Update cannot currently check for updates, because the service is not running. "  You may have to restart your computer. "When I try to download the service pack from the Web site it is usually interrupted with another error.  I tried to go to the Toshiba website and download the drivers needed and utitilities but nothing seems to work.  I am at a loss to try to seek and find a solution.

  Are you sure that the original problem was caused by a failure of the HD, did you test that the hd with the utility bootable disk from audit?

  As if you reinstalled to a new HD using that the required all defined recovery Tosh disk drivers would have been installed in this process.

  Assuming that Tosh then rebooted successfully after recovery, windows update would have run some important updates automatically. If that failed then it would seem that something is happening with your system.

• Re: Satellite L505-13Z - nothing else happens after the BIOS update

  Has anyone ever imagined a (free or inexpensive) solution to this? It happened to my L505-13Z a few days ago.

  He sent for the service, but I'm afraid it's going to cost me: S

  Hi Cvalda,

  If something went wrong during the update of the BIOS you can do anything to reflash the ROM module because special tools are needed. This is possible only from an authorized service provider.

  So it was good has sent for service but let's wait to what say guys. ;)

• Satellite C650 - PXE boot error message

  I have a problem with my laptop.

  When I connect to my Windows 7 tells me an error. The message is: "check the connection of the cable PXE - M0F: outgoing Intel PXE ROM no boot device insert boot disk and press any key any."

  How can I solve this problem?
  Thank you.

  This message occurs when you start your laptop or at the start of Win7?

  As far as I know this message appears immediately after the Toshiba start screen.
  Can you please confirm this?

• Satellite L505-13W BSOD error

  Hello guys,.

  Thank you all for helping me on the last thread.

  I intalled a new copy of Win7 ultimate on my PC now.

  But now it shows BSOD... on the following questions...
  I can't understant what the problem with my knees. The issuues are noted below.

  IN CAR IRQL NOT LESS OR EQUAL.
  PAGE FAULT-IN-NO-FAULTS AREA.

  Please help me if someone has the solution...

  Thank you.

  Didn t you solve the BSOD issue here in this thread?
  http://forums.computers.Toshiba-Europe.com/forums//thread.jspa?threadID=67135

  You got the BSOD using the preinstalled Toshiba system?

• Satellite L505-13Z - strange noise in the audio output

  Hello

  I had a problem with my speakers (probably the one on the left): starting Windows or when windows live notifies a new incoming message sound I hear is not clear, but there is a noise similar to a robotic sound. Sounds like my speakers don't work well. 10 days ago, I bought my toshiba.

  Thank you very much

  Hello

  > to start windows or when windows live notifies a new incoming message sound I hear is not clear, but there is a noise similar to a robotic sound. It looks like my speakers
  > do not work well. 10 days ago, I bought my toshiba.

  What happens if you connect the headset and check what's happening? When you listen to the music it exists?
  I think that you have to play with some settings of his windows event.

• Satellite L505-112 - 31 error code in device USB modem Manager

  I have a USB stick modem: Huawei e172. I downloaded the latest drivers for Windows 7 64 bit. I have a Nokia n95 with firmaware update to version 30 and the latest drivers...

  Is causing me this problem in Windows 7:
  This device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

  To start I have the problem with the huawei e172. After the update of the Nokia n95, I have the same problem with this phone.

  Excuse me for my English but I'm from the Italy.
  Technical support Microsoft tell me that the problem is on the Toshiba Windows 7. In fact, if I try the modem usb stick on another pc with Windows 7 64 bit it works fine.

  Hello

  It's really hard to say what causes this problem on your laptop. Do you use the same drivers on the other PC?

  Are you running the factory settings or you have installed your own version?

  In your case, I'll try to update the chipset drivers on and BIOS. The two you can find on the Toshiba site.

  Alternative you should contact the manufacture of your USB modem. Maybe they can tell you more

• Satellite L505-S5990-F3-F200-0002 error recovery disc

  Hello

  I have a Toshiba Satellite L505-S5990 and I had to do a system restore. I ordered the recovery of Toshiba and equip the number one disc discs. It took me to the Toshiba Recovery Wizard, I used the option completely format the hard drive, all partitions of wiping then in market and so fourth. I put in disc 2 when you are prompted, and click Next. Everything was fine until the end, when I received an error code F3-F200-0002 at which time the only option was to click on next, then the system would be closed. I then tried restoring this time using the default options to factory restore on the restore disc. I put in disc 2 when you are prompted and click Next. Then, I received the error once again at the end of the restoration.

  What can I do now?

  Hi DustinB22,

  I had a similar problem last month that the recovery disk didn't work correctly. First I thought that the discs are not ok (striped), but then I used a Microsoft Windows disk to format the HARD drive first. After that, I tried again the Toshiba Recovery disk and it worked now!
  So you should try that too. As I have written, you can use a Microsoft disk to format the HARD disk or another tool. Maybe it works

  If this isn't the case, you can also install Windows on this drive from Microsoft.
  Check this box!

• No on Satellite L505 boot device

  I have the Satellite L505 with windows 7 Home Premium.
  My problem is there is no boot device, but sometimes it works and start normally.
  What should I do?

  Please help me.

  By default the BIOS settings and check again?

  Try starting your laptop several times using F12 at first upward and let us know if all bootable devices are listed whenever you do this.

• Satellite L505 - 10 M - TosNcCore.exe application at startup error

  At the start of my Satellite L505 - 10 M, I get this message:
  TosNcCore.exe - Application error.

  The text is: can not start the application of properly (0 x 0000005)
  Click OK to close the application.

  How can I fix this?
  Windows 7 home 64-bit

  Arnold12

  Hey mate,

  As far as I know that the TosNcCore.exe file belongs to the Toshiba Bulletin Board tool. So in your case I would reinstall this app and you can download it here:
  http://EU.computers.Toshiba-Europe.com > support & downloads > download drivers

  Check this box!

• Satellite L505 Windows 7 startup error screen

  I had a problem on my Satellite L505 a few weeks ago and it keeps occurring during each startup.
  Windows starts as usual, but instead of loading blue screen, where you can choose username and password to type I get only a black screen with nothing on it.

  I can't see anything, except for the mouse pointer, which works btw.
  When I press ENTER and type my password to Windows load my desktop and everything works well.
  This problem occurs when you start upward only, once I am connected and I want to switch users there is no this problem.

  I get a blue screen with stupid windows 7 graphics and images of all accounts, so there is no problem choose a user.
  Have you seen such a problem? Or is there someone who knows how to fix this?

  Thank you for your response.

  > When I hit ENTER and type my password Windows load my desktop and everything works fine.
  What password do you mean? Maybe you have defined a passoword BIOS?
  The laptop would not boot until the BIOS password has been set and then the operating system should start.

• Satellite L505 - no error message of support WebGL

  Good afternoon

  recently my younger brother in my tube of virus entry latpop Satellite L505 and q format, fortunately to backup all the drivers that you have, but now I want to see WebGL web content and a message that does not support, and I see q dxdiag doesn't recognize anything, only when you run as 64-bit to recognize.

  I have looked for alternatives, but did not, I hope you can help me.

  Greetings

  Hello

  To be honest, I never heard an error like this, and your ad is not very detailed and difficult to understand.

  Can you post a screenshot of the error message and explain that it even more detailed?