Satellite L670D - 15 d does not start successfully after upgrading RAM

Similar Questions

• Satellute C660D-14 X does not start successfully after upgrading RAM

  I have a Toshiba Satellite C660D - 14 X and I brought the new machine RAM
  + Komputerbay 8 GB (2 x 4 GB) DDR3 SODIMM (204 PIN) 1333 Mhz PC3-10600 8 GB portable memory +.

  The RAM is recognized in the BIOS, but when I try to start windows I get a white line in the upper left corner of the screen.

  Any ideas how to fix?

  Notepad starts successfully by using the old modules?
  If Yes, then your problem are the new inserted memory modules.
  Eventually, they are not fully compatible or defective.

  I upgraded my laptop with the modules of RAM 8 GB some time ago and I used Kingston modules.
  They are more expensive but Kingston provide good quality modules and they work great.

  Less expensive modules can cause this kind of problem!

• Satellite M30-107 does not start successfully after using recovery disk

  Hello

  I recently got my hands on a toshiba Satellite M30-107 laptop second hand and decided to freshen it.
  I used the toshiba recovery disk, but after that the laptop is no longer support windows.

  When turned on it shows booting Toshiba disc for about a second then goes to a screen blank and freezes.
  When turned on, once again, a screen will appear an error by stopping and offer the opportunity to start in SafeMode etc but choose one of the options causes the machine to freeze.

  Any help or advice would be much appreciated.

  Thank you
  JT

  Hello

  Sounds a little like the laptop does not start because of the problem of Windows software
  You did not recover the M30 with the original Toshiba that was provided with this device M30 recovery CD?

  I may be wrong, but to me it looks like a recovery CD incorrect has been used and an image with drivers not compatible m has been installed

  You can try to install the OS of Microsoft Win XP original CD and could check if it would be possible to get the notebook ruin using own BONE.

  In this case we (you and me ;)) might know if this problem could be related to hardware or software.

  Good bye

• Satellite A210-199 does not start successfully after the BIOS update

  Hello

  I've got Sat A210-199.
  Yesterday I updated the BIOS, and after that problems occurred:

  While restarting my computer does not start. When I enter the BIOS after a while, it shuts down.
  I guess all this because the temperature of the CPU:

  When I do nothing it is 77 C. I don't think it's normal: (.)
  Computer is very recent, so it's probably not dust inside. And it's so hot from the start, but after the new BIOS, something bad happens.

  Why this temp is so high?
  There is no any process background or something.
  Is this normal?
  And what about this new BIOS?

  To be honest, something like this should not happen. I really don't understand why this is happening. I have updated the BIOS on friends A200 and mine P200 and everything works fine. Here on this forum we can only speculate on this issue, but what you need exactly's professional opinion.

  This probably not help but install recovery image and check with the factory settings. Make sure you also on the lower side cooling fan is not blocked and the laptop can be cooled properly. If the problem persists, you should contact the nearest authorized maintainer and clarify this issue.

  Sorry, but I don't really know what you can do in this situation. I don't see any other way to solve this problem.

  Good luck!

• Windows 7 Enterprise does not start successfully after re - install

  I have just reinstalled Windows 7 Enterprise 32-bit with SP1 on my laptop HP 6715 b. (I use 32 bits for any software that I develop is always compatible 32-bit.)

  After you have re-installed however, it does not start correctly. What came with windows announce "Starting Windows", but the following animation never - start the four lights that turn and turn into the "Flying Windows Icon.  It then crashes right there - do nothing, no matter how long wait.

  If I can put the machine power off and re - start, we are at the "Windows Recovery screen" - because it has not started correctly the last time.  From there, I can choose to make a recovery and return to the last Point of good restoration, i.e. on a freshly installed system before the update of Windows, of course.

  If I select "Start Windows normally", it starts however. But it is not 'Normal '. For example I can't finish my "Windows Easy Transfer".  It says that it cannot connect to my domain name - even if I am connected to my area and have been using it to install other software.

  Or I can do a Windows Update "normally". The last time I tried, it is gone for hours without finding what be - so I left it overnight. In the morning he had apparently found nothing yet.  However when I turned off the machine and then turn it again - he told me there are 211 updates installed.  WHO has literally all day.

  I'm not happy to come back to the last good Restore Point.  I did once.  He has NOT fixed the problem.

  I also tried:

  • Using MSCONFIG to disable all the startup and Services, apart from Microsoft and Kaspersky - no improvement.
  • Do a CHKDSK - revealed nothing.
  • Start in Safe Mode, did change his behavior.  This time I do not have the Herald "Starting Windows".  But turn the machine works again once, return me the 'Windows Recovery screen '.

  Ideas anyone? I'm at my wits end.

  It's OK guys.  I have it sussed.

  He was objecting to the fact that I had my USB with my "Windows Easy Transfer" files on it, plugged during the initialization of the system.

  Also, I was wrong in my thinking on how "Windows Error Recovery".  I assumed that he would do all that it checks before proposing to do a system restore.  It is not, it suggests a restore of the system first.  If you say NO to that, then he makes his audit.

  What is finally here, is that I finally chose an option before he went into the system recovery.  Then, I waited until he was asked to do a system restore.  I said NO, so he went in it checks.  He went through his analysis and finally concluded it was some "system unspecified device" recently added.

  Well I haven't nothing added to my machine for years.  So, I was puzzled.  Then I thought ' well, I don't normally have my key USB is plugged. "  I wonder... ».  I therefore disconnected the USB drive and rebooted the machine.  The rest they say is history.

  Hope this sorry tale helps someone else.  It just cost me four days!

• Laptop HP Pavilion 2320DX g4: computer hp laptop pavilion g4 does not start successfully after update and return to windows 8.1

  Hi, I have recently updated my laptop to Windows 10. He had so many problems and I didn't like it at all, so I just returned my laptop to Windows 8.1.  Since then, my laptop does not correctly every time, and the fan immediately starts to work as well. I can start my pc and connect to my home screen each time.  If the tile is moving or light up when I move my cursor, then I know that I can use my laptop for a little while. It can freeze after getting out a good program. Other times when I start my laptop, everything is dead except for logging on my screen. My Windows key on the keyboard does not work most of the time.  If the screen does not respond the first time I turn, as described above, I can't absolutely nothing on my pc. I can't access the search bar by moving the cursor to top right, I can't open the tiles, I can't spend in desktop mode, etc.  Front I upgraded to Windows 10 and downgraded to 8.1 all worked perfectly, because I've updated from 8.0 to 8.1 Windows almost 2 years.  I have a defective battery. in fact I can only use my laptop if it is plugged. My fan is constantly going, but I don't know if it's my loss of battery or what's wrong with my pc now.  I have described my problem in the Microsoft community forum but have had little response that was not helpful. I was told to go to the command prompt and put in DISM: scan now (which also contained letters more than that, but I do not remember all). I followed the instructions and for 2 days, my pc seems to do better. Then he returned to this problem again. I hope you can help me.  If you have additional questions, post here or please email me at [removed personal information]. Thank you!

  DEB

  @DWESTDEWITT,

  Hello and thanks for the display on the HP support forum.  What you can do at this point that there are several updates released by microsoft and hardware vendors is running the Windows Update Troubleshooter.

  If this fails to solve the problem.  The only option will be to restore the operating system to the previous, until HP gets the drivers so that they can release them on the support page for your laptop for Windows 10.

  Thanks again for posting and have a great day.

• My Windows Vista laptop does not start successfully after the upgrade to SP1

  I use Windows Vista Home Premium. I've updated my laptop with Vista service pack 1. After that my laptop will not start, it displays a message saying "Service Pack did not install. Restoration of the changes. Do not turn off computer. "after windows loading and then the computer restarts and the same thing repeats. I also didn't get a vista CD or a restore with my laptop CD. I tried a solution anywhere, but I couldn't find one. Please help me quickly because I do all my work laptop and I don't don't want lose my files.

  Perhaps you should review this KB

  Things to know before you download Windows Vista SP1
  http://TechNet.Microsoft.com/en-us/windowsvista/bb968859.aspx>

  Information about Windows Vista SP1
  What you need to know before you install Service Pack 1
  http://support.Microsoft.com/?kbid=936330>

  How to troubleshoot Windows Vista and Windows Server 2008 service pack installation issues
  http://support.Microsoft.com/kb/947366>

  How to uninstall Windows Vista SP1 as a troubleshooting step
  http://support.Microsoft.com/kb/948537>

  Windows Vista Service Pack 1 is not available for installation from Windows Update and is not offered by automatic updates:
  http://support.Microsoft.com/?kbid=948343>

  Learn how to install Windows Vista Service Pack 1 (SP1)
  http://windowshelp.Microsoft.com/Windows/en-us/help/133c8953-c9cd-4FA5-8883-03e91bb6f2021033.mspx>

  Windows Vista Service Pack 1 standalone installation) (KB936330)
  http://www.Microsoft.com/downloads/details.aspx?FamilyId=b0c7136d-5ebb-413b-89c9-cb3d06d12674&displaylang=en>

  Go to your retail store, they should have the disk recovery for you or you need to go to your manufacturer directly because the manufacturer is best qualified to support the software that the manufacturer has installed on the hardware, provide your serial number and order the CD on their part. I bet they arrange an expedition to the France and tax treatment for it, but should not be too much.

  Note: The manufacturer was required to provide a way to reinstall Windows. If it is not a set of disks with the computer, there will be a hidden restore partition (do not be confused with the system restore), you would use to return the computer to the State of the OOBE (Out of Box Experience).

• Satellite L70 - A - 11 c does not power on after upgrade RAM 4 GB

  Hello

  I wanted to add 4 GB of RAM and I took a DDR3 1600 MHz SoDimm of Corsair.

  When the RAM is connected alone or together with the original of the RAM, the laptop does not boot at all!
  I tested this with another laptop RAM and the RAM works perfectly.

  I assume that only the type of DDR3L (1.35v) is accepted and not DDR3 (1.5 V). Can you confirm?

  Do you recommend a specific brand or type of DDR3L which is of course compatible with the Satellite L70 - A - 11 c?

  THX in advance
  CortX

  Hello

  AFAIK the module of RAM 4 G compatible Toshiba was number piece + PA5104U-1M4G +.

  The Toshiba PA5104U-1M4G module is exactly the same as the module of Kingston + KTT-S3CL / 4 +.

  Supports the Kingston KTT-S3CL / 4G * 1.35V* and, therefore, I assume that you have to use the modules supporting the 1.35v and the 1.5V modules would cause the problems mentioned.

  Hope this would help you to get the right RAM module.

• Does not start successfully after the installation of updates.

  My sister has installed about 16 updates to windows on his computer. For some unknown reason after these updates, the police on the websites was different (a bit pixelated). She could not know how to solve this problem otherwise that restore to before the update. Then she started to install updates in the sections. She installed upgrading Cumulative security for Internet Explorer 8. He said she needed to reboot to complete the update, so she hit the button to restart. It began to restart and but just sat there for about 8 minutes approximately. She hit the power button to turn it off and then turned back on. The windows icon appeared and the fully charged status bar but then he just sat there on a white screen. We turned off and on again and it has always the same thing. I tried hitting F12 and it did nothing. I hit F2 and it went to the options but I have no idea what I should do, if anything.

  So, can you help me? What should I do now?

  EDIT: I tried a few times to press F8 to boot into safe mode, and it does nothing. I also hit F12 and it brought me to a start menu. I hit "diagnoses" and it did nothing.

  Hi, please check the information here: http://cmdrkeene.com/quickly-repair-pc-problems

• Help! VM does not start successfully after the conversion of Server VMware ESXi 4.1

  Hi, I have install my first server ESXi, everything seems OK and stable. Had a few PtoV machines, but to start I thought I propose our only current VM from VMWare server on our ESXi server.

  The VMware host is Win2003/32 running VMware server 1.0.6 and the prompt is also Win2003/32. I shut down the VM, installed the stand-alone converter on the VMware host and let it do it's thing. Successfully completed and took 20 minutes.

  When I try to start the virtual machine of the ESXi server, it looks OK, but hangs on "Application Startup Scripts", possibly the login screen appears, but then I get messages from "Remote RPC server not available" when you try to open an RDP session. A local login hangs right on the application of personal settings.

  Network everything seems fine, can ping the VM, etc.

  May not work on why the virtual machine should start any differently? Any ideas, anyone please. I am new to ESXi and migrate the virtual computer, but have used VMware Server a lot in the past.

  All advice appreciated...!

  That's good news.

  Which explains, normally, you must do the VMTools upgrade, then the virtual machine hardware, so if the converter upgrades the equipment, the order is bad. Of course, it is recommended to upgrade the hardware to ver 7. So now that it works you can improve the tools and then the vHardware. It might be interesting, if you have enough resources on the ESXi host, make a clone to the virtual machine and the test on the clone in a State (disconnect vNIC) offline.

  Please allow Points if it is useful

• Satellite Pro L850-1DW does not start correctly

  Hello

  I have a client who has a L850-1DW / PSKDHE-00E005EN laptop.

  She keeps pointing out that the computer does not start successfully from the cold.
  She argues that the question arises mainly when the battery starts but sometimes when it is plugged into the mains.
  I can see where point of newspapers that BSOD were registered at the start and that, on more than one occasion, his computer was recovered from a restore of Windows. He has also recovered factory once too.

  Although I've seen the consequences of these issues of "start-up" I have yet to experience first hand with the device.

  I noticed yesterday that the BIOS is outdated (as I had an alert Tempro).
  I upgraded from 1.6 to 6.50. Yet once, I didn't have problems.
  I can't find the release notes for the BIOS so I don't know if this is a known problem that has been fixed.
  I don't know if this "intermittent" defect is just that or if the user has the power button down too hard or for too long and in fact inadvertently crashing NB itself.

  Any suggestion is welcome.

  Otherwise, I guess I have to connect a call with Toshiba.

  On this virtual path, it is not easy to say what the problem is here. In my opinion, you should ask your client if you can make the data backup and install original recovery image. To my laptop computer reviews must be tested with the settings without installation of additional software.

  > I don't know if this "intermittent" defect is just that or if the user has the power button down too hard or for too long and in fact inadvertently crashing NB itself.
  Who knows? Ask your client and show how to start the laptop by pressing the button walk / stop. It must be done slowly and for only one second.

• Windows does not start successfully - only in safe mode.

  I have a 3200 HP with XP Home Edition. Windows starts only in Mode safe when I download Service Pack 3. Is there a way to fix this without doing a complete restore of the system.  I've been running without SP3 because I knew of this issue. Recently, it has been downloaded and now Windows does not start successfully.  Only in Safe Mode.   When I discovered this problem, I was able to fix it, but can't remember if it was fixed without doing a complete restore of the system and starting over.

  Required reading:

  http://h10025.www1.HP.com/ewfrf/wc/document?cc=us&LC=en&docName=c01457284

• Tecra M2 does not start successfully - zeroes appear all over the screen

  Help!

  My Tecra M2 does not start. After the toshiba logo, a series of zeros (0) appear all over the screen.

  -suspect it is caused by a virus, I formatted the HD (in another PC), but still the zeros appear
  -I might want to start in the DVD player, it seems to read the disc, but nothing happens, just a cursor flashing at the top left of the screen
  -J' I reset / replaced the RAM, but still no effect.
  -the power button works, lights and shuts the laptop but does not start.
  -CPU fan works
  -LED indicators of work are power, battery, dvd, wireless. Does not have HD LED light on.

  Any suggestions on how to solve this problem is greatly appreciated.
  See you soon!

  Hello

  I think we can exclude HARD disk failure because you are able to format it in another computer.
  As you suggest the RAM modules has been replaced but the problem persists
  So in my opinion, a motherboard problem would be possible

  But as you know, it of really difficult to say what might be exactly wrong
  I think that the technician should check the laptop then it would be possible to say what part is malfunctioning

  In any case, I think a motherboard might be affected

• do not start cc2015 after upgrading Windows 10

  Do not start CC2015 after upgrading Windows 10!

  What can I do?

  A time CC2015 open and that thr program stop and closed.

  Can I read a text at the present time it is not possible.

  What can I do?

  Best regards

  Sandte

  Hi Brucgovn, thanks for the answer! Just sorted and came here to update the post.

  My method is similar, I just do the following:

  1. Go to C:\Program Files (x 86) \Adobe\Adobe Creative Cloud\CoreSyncExtension (this was the only file on the left, all others had been removed from the CreativeCloudCleaner use of the Adobe Creative Cloud cleaning tool to solve installation problems running
  2. I came across the problem trying to remove, so used Unlocker (Download Unlocker 1.9.2 - FileHippo.com) to unlock. Then deleted. It's explorer.exe using the process, which I think caused questions... the process is using the file
  3. Reinstalled and everything seems to work.

• M - series of satellites does not start successfully

  Hello

  I have the following problem: all of a sudden (don't know why, nothing has changed) portable Satellite shows black white screen with all the following:

  (Sorry, translated from German):

  Windows does not started correctly... due to software or hardware change... If the error was due to stop pls choose last functional configuration...

  But this does not, as all the other options (windows boot as normal starting point, in safe mode... has failed.

  No idea what happenend!

  Problem:

  Actually moved to another country and you have forgotten or lost the recovery CD! already contacted Toshiba for the nine, but perhaps when even someone can help?

  If all goes well it s not a malfunction of the equipment.
  In any case, in the first stage, you should try to reinstall the OS to see if this problem is software or hardware related.