Satellite L70 - A - 11 c does not power on after upgrade RAM 4 GB

Similar Questions

• Satellite L670D - 15 d does not start successfully after upgrading RAM

  Hello

  I have a Satellite L670D - 15 d and now I've passed on SSD.
  In this context, I wanted to increase the RAM (2 GB DDR3-1066 original installed).

  I bought the Mushkin 8 GB kit DDR3-1066.
  In the BIOS are displayed both modules of 8 GB RAM.

  After the logo screen, the white course remains the top left corner and the boot process stops.

  Does someone has an idea and can help me?

  The questions is related to the new RAM inserted.
  But I m confused what RAM is installed exactly now; Modules of RAM of 2 GB + 8 GB or a single module of RAM to 8 GB?

  I m request because the laptop Satellite L670D - 15 d supports 8 GB of RAM, and from my point of view of some 10 GB of RAM (2 GB + 8 GB) is too much.

  That's why I recommend you to use 2 x 4 GB RAM modules.
  Kingston modules provide good quality value ration. Modules are not the cheapest, but in most cases, these modules don cause compatibility issues t. You know

• Satellute C660D-14 X does not start successfully after upgrading RAM

  I have a Toshiba Satellite C660D - 14 X and I brought the new machine RAM
  + Komputerbay 8 GB (2 x 4 GB) DDR3 SODIMM (204 PIN) 1333 Mhz PC3-10600 8 GB portable memory +.

  The RAM is recognized in the BIOS, but when I try to start windows I get a white line in the upper left corner of the screen.

  Any ideas how to fix?

  Notepad starts successfully by using the old modules?
  If Yes, then your problem are the new inserted memory modules.
  Eventually, they are not fully compatible or defective.

  I upgraded my laptop with the modules of RAM 8 GB some time ago and I used Kingston modules.
  They are more expensive but Kingston provide good quality modules and they work great.

  Less expensive modules can cause this kind of problem!

• Satellite L30-134 does not access BIOS after upgrade with SSD

  Hello

  I have a problem with my old Toshiba L30-134.

  When I try to replace the old with new SSD HARD drive, I can't start BIOS.
  But when I remove the DVD-ROM laptop and leave there only SSD, then BIOS can start and I see the drive detected. DVD - ROM has PATA/IDE interface.

  I also tried IDE adapter SATA (like this: [adapter | http://goo.gl/W3TpXt]) for replacement of the DVD-ROM with second SATA HDD and I had the same problem when the disk was present in the adapter.

  When the second HARD drive was not present in the adapter, BIOS began. And it's not just about BIOS.

  Computer is blocking on startup TOSHIBA logo screen during the hardware detection and there is also no error message.

  I can't change the settings on the device SATA IDE/AHCI mode. Is there a workaround with riders or a software solution?

  Thanks for help

  Hello

  > When the second HARD drive was not present in the adapter, BIOS has begun. And it's not just about BIOS.

  You replaced the STRANGE with a HARD drive?
  It won't work buddy. The s laptop computer's optical disc drive supports IDE controller. The HARD drive seems to support the SATA controller.

  The laptop does not power upward because the POST (power on self-test) cannot be passed correctly. During POST the laptop s material will be checked for a possible malfunction or compatibility issues. In your case, the hardware is NOT compatible and that you can't change that.

• Portege R30 does not SSD start after upgrade SSD and HDD

  Hello

  I have improved my Portege R30 - A to add a second SSD (Crucial M550) replace the optical with the new SSD drive with caddy.

  But now the system does not start automatically from the original SSD.

  I could press F12 while turning on my laptop and make it appear the start guide. Here I can see my original SSD and I can boot from it properly.

  In order to boot in the BIOS, I see only the HDD/SSD, USB, ODD memory... It doesn't gives me the possibility to choose between SSDS.

  In any case when I boot in this way than getting blue screens after awhile in win7.

  I tried to install a HARD drive as the second drive instead os SSD and her resut is the same.

  Is that what I can do to solve this, now I have to use the second drive as an external USB drive.

  Thank you

  Hello

  This ODD of SSD/HDD replacement is not always possible and in many cases, the BIOS will not handle and will not recognize the new HARD disk correctly.

  That I can remember some old laptops Toshiba Tecra and Portege that supported the functionality of Slim Select Bay were able to manage the 2nd HARD drive instead of driving WEIRD, but this was not possible due to the available selection slim Bay.

  In your case it looks like the laptop so that the BIOS does not support this function and, therefore, the additional SSD/HDD isn't recognised correctly.

• Equium M40X does not work properly after upgrading the BIOS

  OK, well... I'm not a computer scientist, but I have a bit of trouble on my hands and I don't know where to go for the right help, so I came here.

  Today I started my lappy to confront an illuminous Green Office... not all it is green just of great spots here and there. Happened to me before, but it disappears after about 15 minutes, but today his guarded it usually hours and is still as he.

  I looked everywhere on the net for a possible fix but nothing helped, even though I've heard somewhere that an update of the BIOS might do the trick, so natually, I did... I came here and searched for my Equium M40X, found, downloaded and installed the latest version...

  but now I have a screen with a resolution of half of what it should be, it went from 1200 x 800 or something like that... to 1024 x 786 and I always get the green screen problem... the program toshiba provided for the update of the BIOS does a backup file (BIOS. (BAK)...

  I can't restore the old BIOS would set the screen resolution, but I'm just helpless as to how I go about it. I find the file, but I have no way to open/run it

  I've had this laptop for about 2 years now, I know probably just getting old and a bit tempermental, but if theres no way you people out there can help, I would much apreciate it :)

  Thanks a bunch - Ash

  Hello

  I Don t think the biosupdate is the reason for the reduced screen. It does not sound like a software thing, but rather a hardware malfunction.

  Is your normal screen during startup? If so, I'd say just remove your existing display drivers and install the new. But if it s like you described then it must be a hardware problem and the machine should be checked by a technician or at least a service partner.

  Would be better if your bring your machine to an ASP for a checkup of material.
  If you need assistance to find the ASP closest, try this link (the ASP index):

  http://EU.computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/generic_content.jsp?service=EU&ID=ASP_SUPPORT

  Welcome and good luck

• computer does not aftwr trying to upgrade ram

  I just upgraded my ram on my hpdv6 and now the computer does not even start.

  Hello Deborah,.

  Thanks for the post.

  We need additional information to help you better, please answer the following

  1. What RAM slots that you use on the motherboard?
  2. Have you tried to move the RAM to grasp in other slots?
  3. Have you tried to remove the RAM upgrade and returning to more RAM? System now starts?

  Use your old set of RAM to boot into the BIOS, and then manually change the voltage and the timings to the specifications of the new RAM. Save and exit, turn off the machine, put the new RAM in and check the status of the issue.

  Note: BIOS change / semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

  I suggest also please contact the manufacturer for help bettre.

  I hope this helps.

• Phone of blackBerry Smartphones does not work properly after upgrading Poynt

  Hello.

  Yesterday, I upgraded my poynt app, which seems to have causes all types of problems with my phone.

  (1) my email account icons have all disappeared, although it recognizes new messages, I can't access it.

  (2) the device does not allow me to access my texts all the time as well, and I get errors such as:

  Eception exception: application_net_rim_bb_message_app (231) does not.  I had the same message with several different numbers.

  I also have java.null messages, even if it is rare and I don't remember the exact error.

  (3) desktop manager cannot access the device, it does not allow me to backup my data.

  (4) I tried to reload the os, and applications but it fails because it cannot back up data...

  I'm lost and can't seem to find help on the net for this, and at this point, I want to just wipe the slate and start over from scratch.  Maybe completely reload the software or something.  I have most of my contact information on my sim card from my previous phone, data loss would be minimal...

  can someone help me please understand what to do.

  Info on the device

  Your carrier: att

  Model information and the version of the OS (go to settings, then Options, then):

  8900 v4.6.1.231 platform 4.2.0.108

  Apps and free space

  hard battery pull did not.

  Installed apps and their version if possible.  I have several apps installed:

  Poynt, bloomberg, score, xenozu, facebook, bablphone, CBS Spanish football, dictionary.com, anchor.  all are the latest versions, except for some reason any phone does not recognize that I have the latest version of home.

  but the last poynt update caused this, and I have already deleted poynt.

  Thanks in advance for your help.

  Thanks for your help.  So a question I had was that my camera was unable to save all the data, and therefore loader did not work properly.  I read somewhere that you can stop the car to the top, did this and reloaded the new os.  I think that things are finally working

  Thanks again for your help.

• HAdobe Illustrator CC 2015 does not work properly after upgrading from 2014 CC

  Adobe Illustrator CC 2015 does not work after update from 2014 CC. I have a black screen and I am unable to work. Tools work, but I don't see any results. Could you help me solve this problem? Thank you!

  Try the toggling of the GPU preview

  Display > GPU preview
  Windows: CTRL + E
  MAC: CMD + E

  You can also try switch to wireframe mode.

• C55-A-100 satellite does not power down after update BIOS 1.30

  A week ago, the Toshiba software installed on my C55-A-100 Satellite suggested that I installed a new version of the BIOS to 1.3.

  Since installing it my Satellite will not turn off.
  If I close the lid the screen turns off but the laptop is running, if I open the lid nothing happens and I have to keep my finger on the power button to force it to close.

  The same thing happens if I press the power button to turn off, blank screen and it continues to run, then I have to force a shutdown by holding the power button pressed down. I also noticed that the satellite seems to take ages to power.

  Can anyone provide a solution or experienced the same problems.

  The Satellite is running win 8.1

  Thank you

  Ben

  Please change, as described on http://aps2.toshiba-tro.de/kb0/TSB2B03EY0002R01.htm and try to proceed to a complete stop.
  It work correctly?

  Have you noticed this problem just at the moment where you change the options of closing lid and pressing the power button?

• Satellite L840/03R - FN buttons does not work properly after Win 8 upgrade

  I bought a new L840/03R and installed Windows 8 using the Toshiba Upgrade Wizard. There is no error message.

  The function keys do not work with the CTRL and ALT keys So I can't use the shortcuts like ALT-F4 to close windows - which gives "second screen" options. It does this for F4 on its own, or by pressing CTRL, ALT or SHIFT key.

  In addition, F11 activates / deactivates sound we / off rather than go full screen in chrome. F12 allows flying mode instead of "Save as" in word.
  Just downloaded and installed the package of value added.

  Am I missing something really obvious?

  * Key change function in series Satellite and Qosmio 800 *.
  http://APS2.toshiba-tro.de/KB0/TSB2903E00000R01.htm

  + New computers in the series 800 satellites only use the 'F' numbered keys without using the FN key to get the function. +
  + You can return to the traditional two keys FN key combination if you want by making a change in the BIOS or the HWSetup. +

• Satellite L755 does not detect DVD after upgrade Windows 10

  I'm probably being stupid, but my dvd internal or usb Samsung drives are recognized today. The two spin up, the USB gets pling a little when I connect and disconnect. I found help topics on the removal of media creator Toshiba backup software, did this, and nothing has changed. I am now confused. He is not helped by Windows 10 hide the Panel etc...
  Anyone have any ideas?

  I managed to fix it myself. I found information about incorrect information in the registry. So with care and concern, I used regedit to remove two incorrect lines in the registry. Everything works now.

• Satellite L50-A-111: dimming does not work properly after Win 8.1 upgrade

  Hello

  I have a problem with my laptop computer truebright LED monitor.
  Brightness works correctly, but the brightness variation is not.

  I should be able to choose from a range of 0 to 100% in both, but in gradation brightness that I can not only get up to 10% even though it says its 100%
  because when I level down it says 8,6,5,3,1 level and 0 when I get home eco and when I max he says 10% for 1 second, then 100%.

  Oh and something important, change the brightness variation has no effect at all, I think it's just stuck at 10%.

  But I know clearly that it is 10%.
  I tried everything so far, restore archive and the registry.
  It wasn't even until I restored the registry. I also tried advanced options that once solved this problem for me, tried everything, expect to reinstall the operating system.

  I installed windows 8.1 Windows store recently I don't know if its related.
  All my drivers are up to date.
  Happened yesterday after Batman Arkham City GOTY installing and disabling the Anti Virus, Firewall, etc...

  I don't know what else to try, im really frustrated, I can't handle this without the gradation of light at its maximum. My only concern is to reinstall the operating system did not solve my problems.

  Please give me some info on how to solve this problem, I'll try the registry if someone can help out me.
  Thank you in advance.

  My best regards,

  Sir. º Micael liberal

  Hello

  To be honest I m a bit confused.

  You said that you have upgraded to Win 8.1
  After these updates, you must update all the Toshiba drivers as mentioned on the 8.1 win Toshiba upgrade page.
  On the page of the Toshiba UE driver you can find the installation instructions that will show you how to install / update all drivers.

  This is very important!

• HTP.p does not like usual after upgrade to the apex 4.2.6

  Hello everyone,

  We have recently upgraded the Apex 4.0.2 on Oracle 11 g using Embedded PLS door of entry to the Apex 4.2.6 on Oracle 11 g using ADR.

  The initial series of unit tests seemed well until a few questions supported around "htp.p".

  The scenario is like this:

  1. the user fills some fields on the page-10 and click the Save"" button.

  2. This button then performs a redirection to a pop up page where some inputs more are invited to enter.

  3. when the user clicks "OK" on the popup:

  i. an anonymous PLSQL block is executed in the backend (as after presenting processes).

  II. another PLSQL block is executed, which closes the popup windows and returns the control to the parent page.

  This is achieved using htp.p...

  For example:

  HTP.p ("< body > '");

  HTP.p ("< script type =" text/javascript "> '");

  HTP.p ("var alertMsg =" &. P38_PO_AMOUNT has been paid";");)

  HTP.p ('javascript:Alert (alertMsg)');

  HTP.p ("window.opener.location.href =" f? p = & APP_ID.:7: & SESSION.) " ;") ;

  HTP.p('window.) Close (this);') ;

  HTP.p ("< /script >" ");

  HTP.p ("< /body >" ");

  The anonymous block under step 3.i. is well executed and done what it takes in the backend.

  Its the next step which is driving me crazy, I tried to add debugging but to no avail.

  The weird part is that the message "& P38_PO_AMOUNT. has been paid' getting appears on the pop-up itself instead of parent.

  Any ideas or pointers to this problem would be a great help. I have come to the forums and metalink for any position and had no luck so far.

  Kind regards

  Madhu.

  Hi Sunil,

  Thanks for the reply and apologize for the delay in responding.

  But 2 doubts which do not appear in your code:

  1. why you placetag through PTH again? Body will be already present on the page 7

  2. What is "this" in your window close event? 'this' will be indefinite in my opinion

  Thetag and the reference to 'this' was used because the application was developed first on Apex 3.x

  This piece worked through the upgrade to 4.0.2 and it starts to play up only after this upgrade (to 4.2.6).

  I had followed the suggestions from the link you posted, made some changes and the flow is as follows:

  1, as well as the original

  2 as well as the original

  3. when the user clicks "OK" on the popup:

  i. an anonymous PLSQL block is executed in the backend, under process, like submit it: after calculations & Validations.

  II. the 2nd block PLSQL for close & redirect the page is now part of 'Branch of PL/SQL procedure' with branch point ' on Submit: after the treatment (after calculation, Validation and treatment). The PLSQL code is as follows:

  BEGIN
    htp.p('');
  END;
  

  The behavior is always the same and seems not to have changed. I'm a little lost, try different options.

  I'll try to reproduce the scenario on apex.oracle.com and in the meantime of inputs/suggestions would be helpful.

  Kind regards

  Madhu.

• HP940c does not web print after upgrading to Windows 7

  recently unclassified HP Pavilion 9500 from Vista Home Premium to Windows 7 Home Premium. After upgrade, can no longer print to Web sites - using IE 11.0. Before the upgrade was using IE 9.0. Tried to print from multiple sites by using the function "Print" in the "Tools" button Was able to copy information Word doc Web site and print it from there. All ideasas to problem?

  Hi twf42,

  Thank you for being an active member of the HP support forums.  I understand that you have an impression of Internet Explorer 11 problem on your Windows 7 computer.

  I have included a link in Microsoft Internet Explorer required 11.  Microsoft says IE 11 runs only on computers running Windows 8.1 or Windows RT 8.1.

  Microsoft Internet Explore 11 system requirements