Satellite L850 - indicator wireless is not off

Similar Questions

• Satellite L850-1v0 - alert "Cable not connected" when external monitor OFF

  Hi all

  I have a portable Satellite L850-1v0.
  My monitor is an A.c.e.r X233H
  Windows 8

  I have the setting 'Disable the display' 5 minutes.

  However, when the laptop off the screen I get a small box that bounces around the screen stating "Cable not connected". The monitor is connected via the VGA port.

  If I connect the monitor to my other machine it turns off fine and do not show this message.

  How can I get the laptop to turn off the display correctly?

  Thanks in advance
  Richard

  > when the laptop off the screen I have a small box which bounces around the screen stating "Cable not connected". The monitor is connected via the VGA port.

  The message appears because the signal to the external display was interrupted because of the setting: turn the display off.

  > If connect the monitor to my other machine it turns off fine and does not show this message.
  I think that the other computer/laptop supports another graphics card and so this message does not appear.

  Satellite L850-1v0 support and use of the 4000 Intel HD Graphics intern, who is part of the processor Intel® Core i3 - 3120M and this graphics card shows these alerts

• Satellite L850 - special function key not working not properly

  Hello world

  I had Satellite L850 bite of windows 8 64 (pskg8a-07f001) running for only 2 months.
  Only within this week, the special function key does not work do not, whenever I start the pc, I have to go into toshiba assist office then the function key, and then click ok, it will work.

  But the touchpad has been defined as licence also under keyboard setting was defined as special function mode. But don't know why every time you start the pc must go in the function key box, and then click ok.

  When I bought everything is ok, I can use the special function key to turn, up and down the volume and disable wireless... etc.

  Please notify. Thks a lot!

  Have a look here:
  Function key change to Satellite and Qosmio 800 series
  http://APS2.toshiba-tro.de/KB0/TSB2903E00000R01.htm

  You can use the traditional keys FN + F mode or just a F key mode.
  This can be enabled and disabled in the BIOS or the HWSetup

  In BIOS go to Advanced-> system-> the function mode button configuration
  This mode can be changed
  Also remember that the function button is activated too

• Satellite L850-13 q can not write DVD

  Hello!

  Recently, I tried to write several DVDs without success. It's a problem that took place several days ago, out of the blue, since a certain time has passed since I finally wrote a DVD. I've tried several brands of DVD, so the DVD are not the problem. I also used several DVD writing programs (Ashampoo, Nero, ImgBurn), none of them worked. I don't get any errors during the process of writing, in fact, everything works as it is supposed to. In addition, the surface of the disc is clearly written.

  But when I insert the DVD, Windows is considered as a blank DVD. I use Windows 8 (the script used to work perfectly before, also under Windows 8) and I am very sure that no harmful changes to the operating system has occurred, since I also did a clean installation of Windows, the result of Scripture being the same.

  DVD player satellite L850-13 q (TSSTcorp CDDVDW SN-208AB)

  Help?

  Have you checked DVD burned on some other PC? Are all recognized as blank discs?
  What is with the CD? Have you noticed the same problem with burning data on CD empty?

  It's really strange question, and it's not easy to say what can be the problem. If I understand you just the same problem persists with the installation of operating system clean (factory settings), right?

• Satellite L850 - Win8.1 will not let me install the chipset drivers

  Hello

  After I've upgraded to pro 8.1 windows 64 bit 64-bit windows 8 (preinstalled), I thought that windows will not let me install the chipset drivers (downloaded from "toshiba site" for windows 8.1 pro 64-bit), but they stay with windows drivers installed for them.
  The Device Manager displays all installed and properly using. In addition, during the implementation was executed to install the chipset driver, he skipped most of them, to install a missing driver only (unfortunately have not kept any screen to show). I tried to install using the Device Manager (automatic search or manually navigating the computer files downloaded from the site), but it keeps saying that the drivers are up-to-date (drivers with the version from 2006, when later seen on the site are 2014). Any suggestion what to do?

  Model name: Satellite L850-1MK
  Version of the operating system: Microsoft Windows 8.1 Pro 6.3.9600
  CPU: Intel (r) Core i7-3630QM cpu @ 2.4 GHz
  GPU: AMD Radeon HD 7600M

  Hey... good news.
  Thanks for the comments.

• Satellite L850-150: Webcam does not work

  Hello world!

  First of all, sorry for my English not good enough. I'm from the Spain and I bought a laptop Satellite L850-150 less last year.

  The problem is that I have not tried the webcam so far, and when I did, it does not work!
  When I used the webcam application, it is said: "it is impossible to start the webcam. Check the camera and restart the application or computer.

  I reinstalled the driver for the webcam, but it does not work still... you have any idea or solution? Thank you

  Hello

  What is the status of the webcam in Device Manager?
  Webcam is properly recognized?

  The webcam can be enabled and disabled in the BIOS.
  That's why I recommend you to check the BIOS settings.
  BIOS-> Advanced-> Configuration-> webcam system

  If his permit and if the webcam is properly recognized in Device Manager, I think that you must uninstall webcam once more.
  Then you must clean the registry using some tools like e.g. CCLeaner. It is a freeware software. By using this software you can remove some temporal files and can repair and clean the system registry.

  After this short cleaning procedure, restart the computer again, download the latest webcam software of the Toshiba page and install again. Reboot once more and then try to stars of the webcam.

• Satellite Pro L40 Wireless does not and wont stop correctly

  Hello
  just got a Satellite Pro L40-15 1 week ago and it's been downhill.

  The Wireless does not work (and yes the switch is activated and drivers installed). Sometimes windows recognizes no device when I boot.

  And when I stopped he said blocking down, but crashes just on this screen.

  Now, I'm an advanced user, so I've tried many things. Can anyone help?

  Thank you

  As a first step, I would recommend to use the Toshiba Recovery CD and renew the operating system.
  Then update the Vista of the State. I mean to install patches and fixes Vista all published.

  Check this thread:
  http://forums.computers.Toshiba-Europe.com/forums//thread.jspa?MessageID=107665

  Here you can see that a missing patches can have a bad influence on the wireless network card and the entire operating system!

  Good luck

• Satellite L500D-163 - Wireless does not

  Laptop: Toshiba Satellite L500D-163 (with card wireless 802.11 b/g/n)
  Router: Pirelli Discus (having support 802.11 b/g).

  Hello

  I bought a portable Toshiba, Satellite L500D-163, two days ago.

  Windows 7 and Ubuntu Linux 10.04, the Wireless does not work. It shows all the available wireless network neighborhood, including mine, but it connects to my network.

  I also have an Acer laptop that connects to my network wireless without problem.

  I placed the Toshiba laptop side by side with my Acer laptop and tried all the options:
  802 11b, 802.11 g - WEP, WPA, WPA2
  with simple passwords of the style: "00000000".

  and SSID wireless to the router changed something as simple as "abcde".
  Computer Acer laptop connected without problem in all cases, but Toshiba didn't connect.

  In Windows 7, the connection information appears as connected but 'Limited' and the software Toshiba says that the laptop is not getting an IP address.

  I manually entered the IP address (192.168.1.2), subnet mask (255.255.255.0) and the default gateway (192.168.1.1 router =) below the configuration in Windows 7 wireless card, but it did not work.

  The laptop must support Toshiba, or y at - it an incompatibility with my router?

  Thank you.

  Great! Thanks for that!

• Satellite Pro 6100 Wireless does not work after restoring from HARD drive

  After that restore disks for installing a new HD and use and to update XP sp2, the Wireless does not work and if the card is installed XP hangs then works in fits and starts. If the card not in place, not bad at all.

  Booting from a Linux CD, the card works perfectly! I assume that the driver is the problem. The wireless card is the original, an Agere MPC13A-20/R, with Toshiba p/n PA317U-1MPC.

  I have found some drivers Agere, but am not sure

  (1) if they are correct
  (2) how to install since the machine works in a way limited with the card in place.

  Any advice?

  Hello

  I checked the page of the pilot and the only available for Windows XP WLan driver is the driver of v.1.11.108 Agere.

  (1) just try to install this driver. If the driver is not correct or is not compatible, then windows will not install the driver and you will receive a notification. You just have to try

  (2) generally you may reinstall the driver from the Device Manager. Open network controller tree, and then you can reinstall the driver.

  But this is only possible if the windows started successfully

  PS: Have you checked the information of Microsoft Windows XP SP2 update on the page of the Toshiba driver.
  I discovered that you need to update several utilities if you have installed SP2 on this laptop.

• Satellite L850 - charger / battery problems, not normal...

  Hi all.

  First post and all, I had a glance through to see if I can find my particular problem, and I don't think I can.

  I posted this in another sub-forum, but then realized it's here... oops!

  A L850. It will work fine on battery, but only supplies not the charger cable. Helpfully, a colleague also has an another L850 (I bought two together) so I can charge my battery of separately in his machine.

  If I start the machine on a charged battery, it works fine. If you connect then the power adapter, the led is lit on the front of the machine, but it's clearly not load the machine works until the battery is flat and then turns off and will not turn on back until you charge the battery apart and put it back in.

  Whenever the machine is powered, it also complains that the RTC battery is flat, and you will need to set the time in the BIOS. It is the coin cell CR2032 internally on the motherboard isn't?

  what I don't understand, is that the unit understands clearly that the charger is plugged, as seers to say it is the battery. Except that it isn't, and is not to be unity. Œuvres battery for about 40 minutes of our days, after that, dead machine.

  Any ideas? I suppose that there is something wrong with the internal charging circuit, but the fact that the LED lights up when it is plugged suggests otherwise...

  Thanks for all the ideas.

  David.

  More information on this type of bit. When it is plugged in, the icon on the screen says "Plugged in, charge", but battery icon animates not charging about 10 seconds, then stops, and battery is clearly not charge as % drops away slowly.

  I found a Google one of them is the "remove all, hold for 30 seconds, reconnect power. This made no difference. I also found advice to uninstall the battery from the device manager driver software and allow it to re - install. This done, still no different.

  I got the hard drive and in a USB enclosure to retrieve all my files and am doing the 'factory restore' option I think that this is a restore hard disk partition. This work is far away, but in my opinion, is still running on battery only, so do not know if this is going to end!

• Satellite L750D-1GC - Wireless will not light back?

  I disabled the settings a few days using Fn + F8 wireless and used an Ethernet cable for a few days for the internet, now I'm trying to turn back on the flash button is just saying 'turned off wireless communication, please activate the switch of communication. " I tried to go to the C drive, program files, Toshiba, TBS, TBSWireless bit it dosent nothing or it simply does not run.

  I have no idea what to do, my laptop is a L750d-1GC

  Have Hmm you tried to uninstall and reinstall the driver Wlan?
  Recommend you do

  The L750d-1GC laptop seems to be equipped with the Atheros AR9285 WLan card.
  The Wlan driver should be available on the page of the Toshiba UE driver so download the package and install again.
  Don t forget to restart between the installation process.

  Your comments would be appreciated.

• Satellite L750/05q - Wireless LED not working not

  Have a L750/05q running Win 7 64 bit.
  Wireless works fine but the Wifi led not lighting up when wireless enabled, only the bluetooth led indicator lights when Bluetooth Wifi on or on.

  Toshiba listed last Toshiba site update driver from Atherios - 9.2.0.316 (my model is not listed on their support site to THE), but still open-ended. Wireless works fine.
  Also updated also, the network driver (Realtek)

  Wonder if it's just a hardware failure rather than the driver.

  Any ideas? Thank you.

  Hello

  BT and the Wlan using a LED indicator.

  This means that the light flashes orange when the BT and Wlan functions are lit!

• Satellite L40 - the Wireless does not connect until svchost has been disabled

  Hello.

  I have a Satellite L40 without BONES, I bought and I installed a XP/SP3. I have a small problem when I connect to my wireless NET. It does not connect until I open the Task Manager and remove one of the two svchost process open with the name 'network service '.

  Someone has an idea of why this never happens and how to fix it (I can opperate thereafter, but is a little annoying to have to do each time).

  Thank you.

  Tried to reinstall the wlan drivers and utilities already? When you do so, you should check the download pages of Toshiba for the latest version of the driver.

  Is the WinXP installation you have performed, had integrated SP3 or SP2? Because I would like to know if wlan worked with SP2.

• Satellite L850 - speaker right does not, Win7 32 bit

  Right speaker L850 satellite does not work in Win 7 / 32-bit

  That headset stereo speaker OK.
  Thank you for your good advice;

  Best regards, Joh

  Check please if the Toshiba PC diagnostic tool is preinstalled on your laptop.
  If so, run it and check the operation of the equipment.

  I presume that this tool will ends with the same result. On this virtual path, we cannot say with certainty this diagnosis, but I assume that the speaker is either faulty, or there is a problem with the speaker cable.
  Good advice? Contact the nearest Toshiba service provider and ask for help.

• Satellite C660-108 - Wireless does not work

  Hey everybody,

  New to the forum, I had to sign up because of a problem with shame. I would like to apologize in advance because I know nothing about how computers work.

  I have a toshiba satellite c660-108, windows 7 OS. Yesterday I was updating it and I used it very well after that I restarted. He stops and went to bed. Today, I turned on and he did a system restore, don't know why. So all went through and then it wouldn't connect to the internet wireless, only ethernet cable (http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=69127&tstart=0 - same problem as far as I can tell).

  I'm in the middle of my diploma thesis and word does not work now, so I did a full factory restore hoping everything would be ok. This isn't.

  Ive tried to download the driver toshiba wireless, just didn't work. It currently downloads Realtek but I'm sure it won't work either.

  How to get another wireless network card?

  Any help would be appreciated.

  Thank you

  James

  The essential is that you it works again.
  So congratulations. :)