Satellite M100-233: stops right after the "XP" logo
Hello
I have a Satellite M100-233 with XP Home Edition SP3 (in Portuguese)
When it is connected to the mains and the battery is not fully charged, sometimes the yellow light does not shine.
Check the voltmeter application when this happens, tells me that the battery is on, the energy source is the sector, but the battery runs down.
As I continue to use the laptop, the amount of the battery is reported as progressively less, until he tends to zero, then the laptop just turned off, as if she was not connected to the mains.
Even if I start with the battery charged to 100%, after a couple of hours (sometimes more, sometimes less) the same thing happens.
From an authorized dealer, they told me that it was probably a short battery shorted out.
Get not that: * if she take the battery out of the laptop and turn it on:
-Most of the time it turns off right after the "XP" logo.
-It seems that this happens more often when the battery was fully charged the last time that I used it (strange! "I imagine this?)
-Also sometimes happens after that I use the laptop for a while
The only unusual bios message I get is "no TPM or TPM has a problem." I guess it has to do with the cryptographic protection, so I imagine that this has nothing to do with this issue.
About two years ago, there was a problem with the battery (it ceased to be recognized as present by the laptop) which has been repaired under warranty: they told me that they had replaced the motherboard then. However, at this time there that I could continue to work normally without the battery, which is not the case now.
I would be grateful for any advice. The most annoying is that this problem follows an irregular pattern, and the diagnosis, the dealer gave me seems hard to believe. As I use my laptop to collect data for research abroad, it is quite a risk for me to use it if I can't be sure when it will turn off on its own.
Hello
To be honest, I doubt that anyone here in the forum would be able to provide an exactly the answer to this question
I think that it of almost impossible to say what's wrong without running any hardware checks.
But to me it looks like a card mother number possibly it s power of electronic power supply which is part of the motherboard.
What to say, maybe you need a new motherboard, but the new mobo is an expensive item, and in my opinion, you should first check if it is s to replace the motherboard or buy a laptop second hand for the same money.
Tags: Toshiba
Similar Questions
-
Hello, I have this problem with Toshiba satellite A300.
I deleted several files and folders of my drives C and E. To restart the computer, it only shows the Toshiba logo then a slightly gray white screen on a thorough inspection. Whenever I press CRL + ALT + DELETE, the computer restarts and behaves in the same way.
I tried to use an external monitor, but there is no difference. The tent to start using a CD/DVD, same behaviour occurs, it does not start and screen remains blank after the Toshiba logo, I tried even to change g the order of boot, but in vain.
What could happen?
Thanks in advance.Hello
It seems that you deleted system files and Windows no longer starts. Have you tried to restore the disk image factory settings or hard drive recovery? Or do copy the Windows installation... It is easier to reinstall rather fix the problem.
-
Satellite M40 - 129 stops starting after the Toshiba screen
Hello
My M40 continues sometimes to start after the Toshiba screen. He stops and all I see is the blinking cursor. No Error Message or something else and normal boot from the HARD drive. Boot from CD (for example. Œuvres of Knoppix). This problem sometimes occurs and traceable for me isn´t.Best regards
SpoonyHey Spoony
Unfortunately on this path, it is not easy to say why this is happening. Each user has a specific configuration OS and we don t know how your operating system is configured.
You can boot OS in safe mode? If Yes check what the problem may be a little. If there is anything you can do I recommend you save all your data and preinstall unit using rescue media. If you do this I recommend also to create two partitions.
Don t compare WXP and Linux startup procedure. As you know that Knoppix using just the RAM and no HARD drive for the race.
-
Firefox extension: 'TrueSuite 5.2.500.16' stopped working after the last update of firefox (30.0), although subject: said plugin activated.
I tried to reset firefox and search for similar problems, unfortunately found nothing.
It is also weird empty space before the address in the address bar
other extensions and addons seems to work very well.
Firefox 30 spent some less commonly used "Always turned on" plugins "asking to activate. To check and change this to TrueSuite, you can use the page modules. Either:
- CTRL + SHIFT + a
- "3-bar" menu button (or tools) > Add-ons
In the left column, click on Plugins. Then on the right, check the setting on the right side of TrueSuite.
Any difference?
Note to other readers: the original poster had to leave Firefox and start it again until it is actually entered into force.
-
Satellite P300 itself keeps restarting after the initial splash screen.
My Satellite P300 itself keeps restarting after the initial splash screen.
Start-up of the first screen with the F2 and F12 options down is displayed, the screen goes black, then a cursor appears in the upper left corner and flashes once or twice. Then the laptop stops and restarts and goes through the same process again and again.
That's all with the power adapter is plugged in. If disconnected, he goes through the above process and close with no reboot.
Any help or advice would be much appreciated.
Post edited by: aic-poppy
Start your laptop and enter the settings of the BIOS (F2). Set to its default value. Restart your computer, and press F8 to access the advanced boot menu.
To start the laptop in safe mode and let us know if it works, try it please. -
Buy unlocked iPhone 7 right after the release date
Friends good day! Let's say I want to buy an iPhone 7 right after the release date before apple officially begins selling the devices free SIM card. I'd be able to come simply to store and buy, for example, an AT & T phone to use with my operator? Because I know that they would be not selling sim free phones in the first two weeks. Or do I have to buy a plan as well and become a customer of AT & T? In other words, I need now a unlocked device, and can I get one without waiting for the start of the free features of SIM card sale. Thank you!
If you buy any iPhone outright directly from Apple full paying, it is carrier unlocked.
-
Re: Satellite Pro A200 - black screen after the BIOS screen
Hello
I'm new to the forum and have a big problem. So, any help is welcome and appreciated.My Satellite Pro A200 turns black after the BIOS screen and a black screen with a blinking cursor. Also just as the screen goes black a beep can be heard which shows windows boot.
I can access the toshiba Setup screen but not the installation of security mode.Kind regards
Hello
You wrote that you can access the BIOS, but have you checked if the HARD drive is recognized properly? Perhaps because the computer cannot start HDD isn't recognized then you should check this.
If the HARD drive is recognized, I would try a Toshiba Recovery disk recovery facility. It seems that Windows isn't able to start and if you reinstall the whole system should help get rid me of this. Go to the start menu and select the CD/DVD drive as a boot device.
Check this box!
-
Hello! I just bought an iphone 6 and I was starting the phone due to what he says, but right after the icloud copy was made the phone do not respond... He says decides to continue, but slice to reload button does not work... What can I do?
See if the troubleshooting steps in this article to take help supported:
If the slide on the upgrade screen does not disappear once you upgrade to iOS 9 - Apple Support
See you soon,.
GB
-
The computer stops immediately after the start, repeatedly or a few minutes after have managed to start it. The error log showed two evenys:
(1) the service Acquisition of Image Windows (WIA) suspended at startup; (2) the server {81ED811 A1F4E726-8CF1 - 11 D 1-BF92-00600} is not registered with DCOM within the required time. After restarting the computer, and after installing all of the updates, I installed the last printer; I unplugged the printer and the computer booted immediately! Does anyone have suggestions, and if I have to update the drivers (hp Laser jet 5 p & hp scanjet 5370C;) How? Please help, frustration to a max; Thank you very much; HeinrichDS
HeinrichDS
Recommendation of the Palcouk of sense what is the operating system and is worth a try. If you're still having problems, then you need to talk to specialists in XP (because it is a Forum for Vista). In this case, please transfer your question in the Forums of XP to http://social.answers.microsoft.com/Forums/en-US/category/windowsxp where the XP experts will be happy to help you.
Good luck!
Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.
-
Inspiron 9300 screen turns off after the Windows Logo screen
Inspiron 9300 my wife became severely infected. I thought I had some weird things start popping up of the problem decided to wipe the hard drive and start over. Unfortunately, I don't have to restore disks when I bought the computer. I install windows xp pro service pack 2 full retail version.
Installation was not a problem until I installed the driver ATI Mobility x 300. I followed directions for installation from the website, do the installation of xp followed of the dell system software update followed of chipset followed video driver. After that whenever I put on, the screen turns off after the Windows Logo. The computer is still running and if I plug an external monitor everythng is fine.
I tried all the troubleshooting tips I've seen in this forum. I did a full install twice. made of safety boots (all right), started in VGA mode (works fine), I ran diagnostics from fn on startup, including express, extended and video tests and they pass all the controls. I'm sure it's a software problem, but have been unable to solve. I've updated the ATI bios although when I run it says already installed and done one installs x 300 driver on 6 ttimes own.
I know it must be something simple that I'm missing. My system is the Inspiron 9300 with 2 GB of ram and the mobility x 300 card. Any help would be appreciated.
-
G62 screen remains black after the windows logo
Hello
I have a HP G62-b05SD. I noticed that many people have the problem of simmular.
I know what makes, but don't know how to fix it.
So here it is.
Sometimes when I boot / reboot system screen turns black after the windows logo, but if I wait a while, I do not hear the star tune up windows, but the screen remains black.
I noticed that this happens when I shut down or restart the system with a usb port (be it a mouse or a stick is not serious)
If I all out en usb port restart or turn on the machine for the first time this day here, everything starts well.
So there must be some driver problems I think with usb ports and the screen or something.
Help, please!
HP G62-b05SD
Windows 7 64-bit
Intel i3
ATI mobility radeon graphics card
Ow and when I get the black screen, the hard reset does not always work.
I also did a startup repair and it showed:
"If you have recently attached a device to this computer as a camera or portable music player, remove it and restart your computer. If you continue to see this message bla... bla... bla... "
I hope you can help.
Hi Frosty1984,
Thank you for visiting the Forums HP's Support and welcome. I read your thread on your HP G62 - b05SD Notebook and having problems with the starter. Here is a link to BIOS update.
What is the USB device that is at the origin of the questions?
Thank you.
-
What type of LAN is installed on the Satellite M100-233
Hello!
Can someone tell me what wired lan type installed on my m100-233-psma0e-0pu01cru. I need to start from a floppy and HARD Norton Ghost disk image by lan, but I can't.Hello
You can find it by yourself! Go to Device Manager and select the area to network adapters network adapter.
Access the properties (right click) and you will get all the details about you LAN card.But as far as I know this laptop is PSMA0E series and supports a 10/100 Mbit (Ekron) LAN chip Intel 82562GZ.
-
Satellite A200 23W stop seconds after pressing the power button / stop
Hello all :)
I just bought a laptop Toshiba Satellite A200 23W a few hours ago.
I turn it on and let it complete the installation of Vista.After the installation of Vista finishing it asket to resturn laptop and from that moment, the laptop is "dead".
After pressing on restart the computer (from Vista) computer turns off without problem, but he never did it again!
After a few minutes of waiting, I tried to start it by pressing the power button.Now when I press the power button, I can hear the HDD work and most of the time until I see something on the screen of the laptop computer stops!
Now, I noticed that both the battery indicator AND the DC IN light are hot flushing and stop Flash at times.
Reading the manual, I guess that the DC IN indicator should Flash in all not well.I tried to uninstall the battery and try to start the laptop, but in this case I can't even listen to the HDD, commissioning!
I try to unplag and replag (on the laptop as well as Jack) power cable but again no result.Any ideas of what past?
Thank you very muchI don't know what the problem is here and, in my view, should not be so important to you. Contact your dealer as soon as possible and to talk with him. Explain the situation. You will get may be new notebook. Otherwise, please contact the nearest authorized maintainer and let check your laptop.
The laptop is brand new and it should work. Please do not wait too long.
-
Satellite A100-233 - how to use the multimedia buttons in Linux
Hello!
I used to use media keys and ALTLinux on Toshiba Satellite A100-233 (who, under the power button)... Its possible? If so, how?
PS: Sorry for my bad English... If you can answer on Russian... =)
Hello
Hmm these buttons belongs to a characteristic of Toshiba and this function needs special drivers of Toshiba.
Unfortunately, there is no drivers for Linux distributions and that's why I put t think you will get these buttons work after installing Linux.See you soon
-
Satellite A100-233: can I use the WiFi for the Peer to Peer network?
Hello
Me & my friend have Satellite A100-233, we cannot have network even see ourselves at the TOP unless we are in place contain the wireless Internet Modem.
If we cannot make network peer-to-peer between us using WiFi?I hope you can help!
Thank youHello
I don't know if I understand your question, but you want to connect two laptops via the WLan. Am I wrong?
Well, this type of network connection is called Ad hoc.Choose Start-> settings-> network connections, and then click the local network connection you want to share. On the left side of the screen under the management of the network, click on "change settings of this connection. Under the Advanced tab, under Internet connection sharing, check the box "allow other users of the network to connect through this computer's Internet connection".
There is also a check box to allow other users to enable or disable the Internet connection, if you are so inclined. If your network doesn? t need to access to the Internet, you can skip this paragraph.The host system must also be configured with an Ad Hoc network connection and a Set Service identify (SSID). Right-click on the wireless icon in the system tray and choose "view wireless networks". Do NOT yet connect to any wireless network that could appear in the box. Click the Advanced button. This will bring up the Properties window of wireless with the wireless networks tab at the front. Click the Advanced Options button at the bottom right of this tab, select the option "networks from computer to computer (ad hoc) only". Make sure that the box "Auto connects to the non preferred networks" is NOT checked. Click the close (once) button to return to the wireless network tab.
Under preferred network, click Add. You now need a SSID for this machine, which is actually the name it will use to announce themselves to the other members of the ad hoc wireless network.
Maybe you are looking for
-
Google has stopped working in firefox 28
Search Google has suddenly stopped working in firefox 28. I noticed when I try to access the url says https://accounts.google.com/CookieMismatch google.com site. I get the same when trying to do a google search with that on the page We have detected
-
I don't remember set up sync ACCT. But am not computer savvy (can get). Check Sync and discovered an acct is set, but not with my email. My friend used my computer and I don't know if she wanted to do, but now ACCT. is his email, and I would like to
-
Enter it on back Satellite Pro 4600
I am running WinXp Pro on a satellite pro 4600 My floppy drive doesn't work anymore, how can I enter dos mode so I can create a backup with Norton Ghost?
-
Satellite C660 - 1F1 graphic Driver Update?
Hello I tried to get a game called Football Manager 2008 to work on this laptop for a long time. I searched the Internet for a solution to my problems running it, but I did find something that works for me. In fact, most of the time, the problem seem
-
Pavilion 23-f319: all-in-one 23-f319 Windows 7 drivers
Hey all,. Looking for Windows 7 drivers for my Pavilion 23-f319. A windows 7 when I recived and had to re - install. Am ideally looking to upgrade to Windows 10, but miss me the drivers for: Network controller PCI device SM Bus controller (USB) Unive