Satellite M110 - Orange light flashes when I push the power button

just before I managed based on the knock off my bed, on a glance the plug that goes into the computer look slightly bent and now when I try to turn it on, it does not work. even when it is plugged.

An orange light is always flashing down the bottem when I press the button.

So is this a problem computer or a power supply problem?

Hi becks88,

Sounds like a serious problem of material... You can start Notepad without AC/DC adapter or is the battery charging adapter?

Try to delete also the adapter AC and the battery for an hour at least. Then reconnect the two and try to start the laptop.

In the worst case you need professional help a :(authorized service provider

Tags: Toshiba

Similar Questions

  • Satellite L20 - Orange LED flashes when I press the power button

    For 6 - 7 times and nothing happens after that, the battery is completely dead and the adapter works fine

    I measured the voltage on the map that powers the battery and found 3.33v on 2 of them, the third is 0 v and the last of them starts by 0 v and goes up to 10v and more

    Hello

    Strange, but it might be a hardware malfunction.
    But first, you should try to remove the battery and the AC adapter. Attendre wait up to an hour, then reconnect the two devices.

    If it doesn t work it could be a motherboard problem or something else. I recommend you contact a technician for laptop.

  • Satellite A500 - battery light flashes when connected to the power supply

    Win 7 Satellite A500 PSAM3A-03P00E.

    Battery light flashes when connected to the power supply (intermittent fault), when I disconnect the sector and reconnect the flashing stops and battery (high capacity) continues to receive.

    Also, when battery light blinks the keyboard backlight stays on when it should white and if the backlight is turned off and the battery light starts to blink the keyboard backlight turns on, all other functions seem to work well.

    Charges of battery and the wedges load properly (when the battery flashes).

    Hello

    Have you noticed this problem since the first day of purchase?
    Theoretically, it could be possible that your battery begins to malfunction
    On the other hand, an electrical problem could also be possible

    However, try this:
    Remove the battery and the AC adapter. Then press and hold button power 30 sec long.
    Then insert the battery and plug AC adapter still does that help?

    By the way: this is the BIOS updated? If this isn't the case, perform an update.

  • HP-G62226TU: my laptop won't turn on when I push the power button

    Hello

    My laptop does not turn when I push the power button / stop and nor adjacent to the plug adapter lights turn on when I put the power supply. It behaves like completely dead. I pressed the button for 30 seconds as suggested in the following thread.

    http://h30434.www3.HP.com/T5/notebook-hardware-and-upgrade-questions/my-laptop-won-t-turn-on-when-I-...

    My laptop is 2.5 years old and was working fine without any problems so far.

    Please suggest.

    Thank you

    Himanshu2303 wrote:

    OK... I learned to get the motherboard changed. How much it will cost in India for my laptop?

    What do you suggest I should do?

    How much will it cost in India?  I have no idea. I live in Europe.

    I suggest to ask a repair shop of PC or laptop.

    If the cost of repair is more than 50% of the current value of the laptop, you would be better sourcing of a notebook replacement.

  • I have a computer that is running Windows xp and when I push the power button, it automatically restarts

    When I push the power button, it starts up but when I see the Windows xp startup screen complete the restart of the computer around and does exactly the same thing again and again, so I can't use it, please help I need my computer =)

    towelsrawesome,
    Thanks for posting on the Microsoft answers Forum.  The first thing I would say is to remove all external devices from your PC (except the mouse and keyboard) and then restart.  If she does not always correctly, then try to start safe mode.  Here is a link that explains the Safe Mode and how to start to it: http://support.microsoft.com/kb/315222

    Post back with the results of these measures.  Also, let us know if something has changed recently on your system (hardware or software) and give us some details about your system.  Let us know the make\model of pc and which package XP version\service you use. Mike - Engineer Support Microsoft Answers
    Visit our Microsoft answers feedback Forum and let us know what you think.

  • When I push the power button on my laptop the lights blink but the laptop does not light

    original title: what is the problem?

    When I push the button my laptop the keyboard lights flash on and then go immediately, that it never comes to the top at all.  I want to know if this problem is fixable or trash?  It's a hp model w/double older processors

    Hey cgmartlynde,

    Try to charge your laptop and then see if it boots.
    You can also take a look at this article to help maximize the battery life:
    I hope this helps.
  • Satellite L550-1CW does not start by pressing the power button / stop

    I have a Toshiba Satellite L550-1cw that won't start, lights up when I press the power button all the lights at the front, the fan starts and he is looking for a HARD drive for about 2 seconds and then stops.

    I tried a new HARD drive, but the same happens.
    I was told that all this must be ignored and buy a new one that is not an option.
    I love this laptop and want to run again as this is the best I have ever owned.

    Help, please

    Andrew

    Can you give us more information on this vulnerability?
    You see something on the screen after pressing the power button?
    You can access the BIOS by pressing the F2 key immediately after switching on the device?

    Despite this whole issue, I think that if nothing is visible on the screen it could be a serious problem with one of the following: RAM modules, motherboard, CPU/GPU.

    From my experience the RAM memory modules are not very expensive (2nd hand might be good enough) and the replacement isn t very delicate in the case where the faulty memory causes this problem, the laptop could be set for a little money.

    But in case of problems of motherboard, laptop repair procedure could be very expensive.

  • Satellite 1005: Push the power button, will turn off the AC power.

    Laptop: Toshiba Satellite 1005

    Problem: When I press the power button and let go, the laptop immediately loses all power.

    I use the power cord plugged into the laptop, the power supply light is green, but when I press the power button and let go, as soon as the power light goes black(turns off), nothing happens.

    Howerver, if I PRESS the power button without letting go, power LED lights, but the laptop won't boot at all, no Startup logo, no sound no matter what.

    It's the second time this has happened, the first time, I let stand overnight and the next day she booted up fine.

    Currently, the laptop is cold, it did not work, but always the same thing as described above.

    There are no changes made to the laptop.

    Any ideas?

    It seems that the contact, the power button is faulty. Better to elevate the laptop to a Toshiba service station for a check.

    I n ' t´t think that it is a software failure.

    Good bye

  • Why Satellite Pro A300 does not start when you press the power button?

    Suddenly my new Satellite Pro A300 does not start correctly when you press the power button. The situation is the following: when I press the power button is displayed the opening of Toshiba (Leading Innovation) and the disappers image quickly. Then there is a black screen for about 30 seconds. There is a rectangular frame with the text Microsoft Corporation under. And nothing happens however long wait.

    In order to get with the trial starting I then shut down the computer by pressing the power button until the computer turns off. ("The hard way to close")
    Now, I press the power button shortly to turn on the computer. Then, the computer starts normally with the photo to open Toshiba and after a few seconds, I wonder to open the computer in safe mode or in normal mode. I now choose to open in normal mode and the computer opens normally and is ready to work.

    What should I do to get a normal departure procedure?

    When the laptop starts normally (after choosing normal mode) stop your laptop properly using START > shut down option. Next launch should be normal.

    When the OS is moving towards the low irregularly will always ask you how to start this new (secure or normal mode).
    The same thing happen on my Satellite A300.

  • Two Macbook Pro, both does not start up, when I press the power button, I hear two disc bit Caryl, I see little light on the front on the displasy release button, black screen, no edge

    It was weird because I've NEVER had two computers have the same problem before. They are the model 2008 2.2 Ghz Core 2 Duo, 6 g of RAM, models of 128 GB of hard drive, the two Yosemite running, both had new hard drives, cables, batteries and RAM installed OWC (Apple approved reseller) and I use Macs for at least 20 years. In about a week, one just blacked out while sitting on my desk doing nothing, the other does the same on a week later. When I press the power button, I hear the drive hard hum twice, then all I get is the little light on the screen release button, that's all. Black screen. fails, nothing. I can press the power button and it will fit off the coast. Is it possible that some of them have infected somehow, or possibly send me the malware that has infected my system? I would not normally only, but for all of them to go down to one right after the other with the same problem just made me think, it must be the same cause, but what?  I had been in a war of fire recently with very ugly people, and I've never seen two Macs have the same exact problem in a row like that right.

    I took readers on the Macbook Pro, put them on sleds and threw them in my PowerMac, and both seemed fine, no problem, started well upward, ran utility disk on them, no problem, so I started to the checklist. Reset the PRAM. Nothing. SHIFT key at startup. Nothing. D at the start. Nothing. V order at startup. nothing. I wouldn't mind even their evisceration and making a portable useful with the parts of the two, but until I find out what the problem is, what can I do?

    If anyone has any suggestions, I would really appreciate it, I've supported every button I can think at the start, tried an inch USB key, boot and disk, this is the same Caryl bit both of the car, no chime, black screen, that's all.

    Thanks for your help.

    Damicon999 wrote:

    Is \Is possible for someone they have infected somehow, or possibly send me the malware that has infected my system?

    no chime, black screen, that's all.

    I don't think they are infected.

    The startup chime indicates that the Mac has made the initial diagnostic tests and there is no hardware problems or fundamental software.

    No edge in your case is a problem.  I think it's the luck of the draw to have 2 failures.

    In or out of warranty you can get for free a 'Apple Service Diagnostics' OTC test

    Genius of booking http://www.apple.com/retail/geniusbar/

    Online https://getsupport.apple.com/GetproductgroupList.action

    check the warranty https://selfsolve.apple.com/agreementWarrantyDynamic.do

  • Just upgraded to lightroom lightroom 6 5.  When I push the download button I get error: 413 header length too large.  Do not download.  What can I do?

    Just upgraded to lightroom lightroom 6 5.  When I push the download button, I get error:

    413

    Header Length too Large

    Will not download...

    Hello

    I would ask you to try another web browser and let us know if problems.

    Kind regards

    Hervé Khare

  • PowerEdge T410 won't do anything when you press the power button / stop.

    My work has recently retired this t410 server. It worked without any problems when he was arrested. I had to remove and destroy the hard drives from the system. After that, I was allowed to bring home for my own use. I installed a new sata drive and plugged into the power supply and a free sata port on the motherboard. I get nothing when I tried to boot the system. This version has the unique power. Power light only lights up when you press the test button. System fan is going at full speed, but stops when you release the power button. Also on the control panel lights 1,2 and 4 and HDD power on and turn until the test button is released. There is a single green light lit on the motherboard, while it is plugged. Apart from that, I have no response when you press the main power button. Can anyone tell how to try to get it up and running again.

    -Who-

    I have not received the answers more so I think that this issue is ignored. So I'll let everyone know what finally happened. I solved my problem after a lot of electrical testing. I found a diagram of the arrangement of the power dell power supply pins and I made myself the best possible meter test. After several rounds of tests, I found several pins that did not have the right voltage. I bought a new power supply. I installed and replace everything. I plugged into the system and it auto fed on itself. I loaded from an OS and it works perfectly.

    Problem solved

  • My his laptop makes a beep when I press the power button / stop and it does not start

    Hello

    I bought a new Dell Inspiron 15z touch ultrabook and when I pressed the power button, it starts to beep and won't start. The screen is totally blank. What should do? Help, please

    -Mayur gala

    Hi Mayur,

    Welcome to the community,

    Sound signal can be used as a diagnostic indicator. The computer may emit a series of beeps at startup if errors or problems. This series of beeps identifies a problem and is called "beep code".

    See the table below which shows the beep codes and the possible problem:

    Overview of beep Code
    Beeps Description Possible cause
    1 ROM BIOS checksum failure The map system, covers BIOS corruption or errors ROM failure
    2 No memory (RAM) detected Memory or memory slot failure
    3
    • Chipset error (North and South Bridge error)
    • Time-Of-Day Clock test failure
    • Gate A20 failure
    • Super i/o chip failure
    • Keyboard controller failure
    System board failure
    4 Memory read / write failure Memory failure
    5 Real Time Clock (RTC) power failure CMOS battery failure
    6 Video BIOS Video/smart card failure
    7 Failure of the CPU Processor failure
    8 LCD SCREEN Failure of the LCD

    Let me know if you need assistance.

    Thank you

  • PC does not start when you press the power button, after that starts automatically as a ghost!

    I have HP Pavilion a6030in, my pc does not start when I press the power button / stop ther, but she starts automatically after some time after that, it works fine.

    Even once when I closed and leave it for a while and still the problem is not resolved.

    Help, please

    I solved the problem

  • Tecra A4 does not light when you press the power button

    When I press the power on button it turns green for 4/5 seconds then turns off.
    "I do all the tests the support on the page:

    * Press on and press and hold the Fn key and press the F5 key repeatedly. If an image appears on the display, this indicates that the image has been activated to a connector for a monitor outside, causing only appear to be off the computer.

    * Connect the adapter to the computer.

    * Remove the battery and unplug the AC adapter and then connect only the AC adapter. Make sure that the power adapter is one that comes with the computer. Try to turn on the computer again, without the battery in the computer.

    * Plug the power adapter into a different plug.

    * The battery, ensure that there are enough energy to start the computer.

    * Press and hold the power switch for 10 seconds (to make sure that the computer is turned off). Wait five seconds, and then tap on and again, hold the switch for three seconds (turn on the computer).

    * Ensure that nothing beats (a sliding plastic cover) in the path by pressing the power switch.

    * Disconnect all devices (printers, pointing devices, keyboards, etc.) connected to one of the ports on the computer.

    * Remove any additional memory, beyond the computer built in memory, or the first module of memory in the computer. If the computer starts correctly, reinsert the memory and turn the computer back on. If it does not start successfully, memory can be inserted incorrectly, it may be defective or the support of memory may be damaged. "Try to replace the module memory."
    In vain:]

    You know? THX

    Hello

    There must be a hardware malfunction.
    You have tested a lot and nothing has worked
    I think there is not much to do, you all tired and I guess the authorized service provider could help you

    If your warranty is valid all should be done for free, so don t you worry and ask the experts ;)

Maybe you are looking for