Satellite M30-604 freezes and the fan does not work after replacing

Similar Questions

• Satellite Pro 4200 overheating because the fan does not work

  I have a satellite Pro 4200 and it keeps overheating because the fan does not work I went in and everything seems ok but then I power it upward but the fan does not work someone can help? all cables are connected the fan run at all.

  Hello

  And how to help her in this situation? If you are sure that it cooling fan doesn t work 100% needs to be replaced.
  By the way: did you clean the unit and remove the dust?

• Satellite P850-30W - the fan does not work after returning from the mode "Eve"

  I have a Toshiba Satellite P850 30W with bios 1.90.

  Sometimes the fan does not work at all after back mode standby on windows 7.
  What happened twice (perhaps several times without knowing me), and Ive had the computers for a month.

  Normally the fan starts to run when the CPU gets more than 50 degrees celsius and stops less than 50 celisus...

  I tried running Prime95 when this fan-this occurs and the time of the computer got dangerously high (near 100 degrees)! the fan did not start at all
  .. .This error could damage the laptop potentinally...
  to get the fan turns once again I have to restart windows

  anyone experienced this?
  I guess that the fix would be to never use standby... or toshiba needs to fix it with an update of the bios.

  > Sometimes the fan does not work at all after back mode standby on windows 7.
  > What has happened twice (perhaps several times without knowing me), and Ive had the computers for a month.

  You said it's happened twice and only sometimes done this means that above all the fans are working well?
  In this case, this would mean that it of difficult to reproduce this problem, but you might be right: maybe a BIOS update would help solve this problem permanently

  I found some discussions on the stand-by mode and fan activity and in most cases, the update of the BIOS was the key.

• Internet and the sound does not work after uninstalling programs, System Restore also not work.

  I noticed that my computer felt a bit slow so I uninstalled a few programs that I knew were not very helpful so I restarted my laptop, and then the network and the sound does not work.

  I tried to use the system restore, but that does not work either and I tried to online solutions, but nothing works.

  Most often when a device does not work, it is because the driver is damaged. Re-install a new copy should help

  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly? SignedIn = 1

  http://captaindbg.com/how-to-update-drivers-on-Windows-7/   (also works on Windows 8)

• Keyboard and the mouse does not work after the release of sleep

  Original title: error keyboard and mouse

  After you have installed Windows 8 I had problems with the keyboard and the mouse.

  If the computer disconnects a half our for example, when I come back, the keyboard and the mouse do not work,

  I can not connect and I have to restart my computer to the power button.

  How can I avoid this problem? It happens every day at least once.

  Hello

  1. you are using a wired keyboard or mouse and wireless?
  2. What is the brand and model of the PC?
  3. have you checked if other USB devices work on the PC after you resume the computer from sleep mode?

  I suggest you follow these methods and check if it helps.
  
  

  Method 1:
  If you use the USB keyboard and mouse, and then follow the steps below to uninstall and reinstall the USB controllers.

  (a) press the Windows logo and X from the keyboard.
  (b) type devmgmt.msc , and then press ENTER.
  (c) expand Bus USB controllers.
  (d) right-click every device under the Bus USB controllers node and then click on uninstall to remove them one at a time.
  (e) restart the computer and reinstall the USB controllers.
  (f), check the question;

  
  Method 2:

  The 'USB selective suspend settings' option in the Power Options can be activated.

  (a) press X and WWindows logo and choose Power Options
  (b) click on change plan settings for the selected power plan
  (c) click on that to change advanced power settings
  (d) Expand USB settings and then the USB selective suspend setting and change them to disabled.
  (e) click OK in the power settings window, and then click save changes in the Edit Plan settings window.

  Method 3:
  If this does not help, I suggest to change the power to its default settings and check if it helps.

  You can follow the steps to do this:

  (a) press the Windows logo key and X set and choose power options.

  (b) under the preferred plans, click on balanced (Recommended).
  (c), click Change Plan settings and more balanced (Recommended) option.
  (d) click on restore default settings for this plan on .
  (e) click Yes to save the changes.

  Now check the issue.

  Let us know if it helps. If the problem persists, please answer, we will be happy to help you further.

• Satellite M70 - 170 - Touch and the launch does not work

  Hello everyone, I'm Sylvain and I'm french, so sorry for my English...

  I have a Toshiba Satellite M70-170, and I have a problem with the program "Hit and run" (1,2,9,0)

  I see the icon then the clock and I can change the settings, but when I press the button of the mouse will work, but not to the touch and launch...

  Can you explain why?

  I love this commercial and I want to know why it does not work.

  I put t know why the touch & launch does not work, but I would try to reinstall again.
  The Touch & launch is placed on the European driver Toshiba page.
  This time it s a v 1.2.9.0 for Win XP.

  Uninstall first touch & launch and after restarting again install it again!

• BDP 3100 Youtube freeze and Yupp TV does not work after the last firmware update

  Hello

  My Youtube app on the Bluray Sony BDP - S3100 drive freezes when I play any video. It says LOADING... and plays the video completely. But the Player hangs and I have to be able to market. This started happening since yesterday is to say 26/06/2013.

  The other problem is with the YUPP TV App.

  After my latest firmware upgrade June 4, 2013 live channels on the YUPP TV app does not work peoperly. It says loading and will market every 5 to 10 seconds. On demand videos are very good. This began to happen immediately after the upgrade on June 4, 2013 (M14. R.0136). but after that, there was a more updated firmware that says that connectivity issues fixed on 08/06/2013 (M14 Version. R.0138). I've updated on my player. Yupp TV questions are still there. YouTube has been fine since then, but then the Youtube above issue started happening since yesterday and I have reported to the Youtube community as well.

  Could you fix Yupp TV, I'm sure that updating the firmware.  Also please check if Yout tube is with the firmware...

  Let me know if you need additional information.

  Thank you
  RAM

  At least I'm not alone, until a few days earlier, alls well, now, I have the same problem, so that makes three of us.  New default factory setting does not so I think a firmware issue, all other channels & functions outside of youtube look... very annoying

• Satellite A200 - 1 M 7: the sound does not work after the downgrade to XP

  Hello!

  As in the topic I have a problem with my sound card - it simply does not work under Win Xp (under Vista everything worked).

  In Device Manager I have two 'points of inquiry:
  -Controller\ PCI memory
  -Unknown device
  I assumed that the unknown device is my sound card, but still can't make it work :/

  I've already upgraded the bios and install page of toshiba Realtek drivers.

  Really need help.

  Adrian

  Hello

  No sound after installing XP operating system. What to say man I searched here in the forum similar threads and it seems that it is a common problem.

  But you worry about don t; I think that I found the key ;)
  After installing win XP, you must update the latter State. Install all the patches and hotfixes provided by Microsoft. You must use the website to update Ms. The tool on this page checks the system and selects all necessary updates!

  Very important are the patches; KB888111 and KB835221
  These hotfixes must be installed before installing the sound card driver.

  The Realtek sound card driver can be downloaded from Toshiba or on the official website of Relatek page.

  By the way; It is very important to install drivers in the correct order. On the Toshiba page, you will find the installation instructions. So please follow the guidelines mentioned in this doc.

  concerning

• Internet and the sound does not work after the ATU Vista 64-bit

  I really didn't want to display in the hope I would find the answer using Google, as I did in the past, but this one i can not find the answer for.   2 days ago I d/l a program called Advanced System Care. I was told by 3 of my friends it works well to clean your junk files, Defragging ect ect.

  After d/l and the operation of the program, I had to leave and shut down the system. Today I start everything is fine, and then I noticed that I have a red X on my speakers. This is not the red X you get when cut there a smaller lower-right next to the speaker in the toolbar. When I mouse over it, it says "Service Audio work not" when I click it to repair, so good it shows all is working (volume mixer control is non-interactive) then I go to control panel and click on the speaker and I get "this computer cannot play audio because the windows audio service is not enabled.»   You want to enable "I click Yes and it brings back me just in the region, that I was when I clicked on the small speaker in the toolbar with the red x.»  Everything always looks the same as it was when I put in place.

  Is there anything else I can look?

  Second problem happened at the same time.  I have the same red x on my 2 computer screen in the toolbar on the bottom right. When I try to repair it it says this "this service cannot be started because it is disabled or because it has no enabled devices associated ' when I go to Device Manager and check to see if it is still showing my d-link wireless there is black! on a yellow background. When I try to access the computer to find local internet connections, it says that it can't find. I know that my Linksys is working because my Iphone is connected.  I already tried to install a cord between my router and my system and it still does not notice the internet even when you try to reconfigure.

  I read where I can make a dirty windows vista installation and fix it. but I really hope that there is a better way.  I also tried to restore my computer to last week when I made a back up and it seems after the use of this program, that he got rid of that as well. So now im out with to be able to roll back before I D/L this close program useless lol

  I'm using Vista ult 64 bit, that the computer is built for gaming and music. OCed Q6600 to 3.2 4gig ram 8800gt 2 in sli on a configuration card XFX mother if any other system or other questions please do not hesitate to ask.  I hope that someone has had this problem and can help me to solve it.  I don't want to reformat my HD or what I really want to pay Microsoft to talk to them on the phone

  Thanks for your help

  After 3 hours on the phone with the microsoft problem solved. Seems some how using CSA and the update of microsoft it limited my computer to start all programs at startup.

• My Toshiba Satellite L675D - S7042 Webcam and the microphone does not work

  Help, please

  Moved to windows

  Hello

  Welcome to the Microsoft community.

  What version of Windows are you using?  Windows Vista, Windows 7 or 8/8.1?

  Is that you improved your system to 8.1 of Windows from a previous version?

  How to uninstall the software:

  1. From the start screen
  2. Type in the Panel
  3. Click on Control Panel (make sure apps is selected)
  4. Click on uninstall a program under programs category.
  5. Find TOSHIBA Web Camera Application and double click it.
  6. Complete uninstallation suite at the direction of the screen.

  Access TOSHIBA support website to obtain the last component to install.

  1. Go to http://support.toshiba.com/drivers
  2. Enter your product serial number
  3. Press GO
  4. Select the camera under filter by
  5. Select Windows 8.1 (64-bit) under filter by
  6. Click on the application of WEB camera at the top of the list
  7. Click Download
  8. Install the application by following the instructions on the screen

  Method 1: Open the troubleshooting of Audio recording

  http://Windows.Microsoft.com/en-us/Windows7/open-the-recording-audio-Troubleshooter

  Method 2: Audio recording in sound recorder: frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows7/recording-audio-in-sound-recorder-frequently-asked-questions

  Method 3: When the sound card is installed, the microphone is also installed and uses the sound card drivers.

  Please try to uncheck the option put the microphone muted in the sound menu. If the problem persists then uninstall and reinstall the sound drivers.

• Brother printer and the scanner does not work after Windows Update.

  Separated from this thread.

  I have the same problem with my Brother ADS2000 scanner and my multi MFCJ4710.  I can print with the MFC, but the Control Center detects or scanners.  They worked and suddenly stopped.  I wonder if Windows update changed something?  Scanners both work with Windows Fax and Scan, but not Brother Control Center 4.  I called support of brother and again, they have said something about TWAIN and I have to do some registry clean.  I tried their manual steps, they sent with the registry fixes and which totally screwed up on my computer.  I had to do a restore and now back to square one.

  Any solution out there?

  It was my dose,

  (1) start search box type menu "user accounts".

  (2) open and select "user account control settings."

  (3) to change the cursor to "never notify".

  (4) 'ok' to save

  (5) fact! You may need to restart you machine.

  PS: this was my fix, it was caused by software AVG anti-virus, AVG has replaced this setting and would fail to wireless for my scanner. It will be useful.

  Rob

• code 511 undetected fan and the fan does not turn or unraced where do replacement or is this question solfware

  code 511 undetected fan and the fan does not turn or did not run where do replacement or this question solfware please help

  [Moved from the community centre of Participation]

  Fan errors are usually hardware problems. There is a fan in the case including detector does not detect that it is available or spinning. This could be a problem with the real fan or the fan sensor.

  Does this have to do with? Are you talking about an error that is displayed by a Windows machine? If so, what version of Windows? When the error take? At boot time? Before or after that Windows allows you to open a session? When you provide no details, it is almost impossible for anyone to help.

• Satellite W30T-A378 from - touch pad and the keyboard does not work

  I have a problem with my laptop, the touch pad and the keyboard does not work.
  Can someone help me what is the possible cause?

  Thanks in advance.

  Hello

  I guess you checked if the Tablet has been properly connected to the docking keyboard.

  Have you tried to unplug and plug the docking again?
  Note: there is a latch on the left you have to move and in order to remove the tablet.

  Perhaps there is a connection problem.

• I have my black getit monitor and the computer does not respound after 2 mnts when I start playing games online

  I have my black getit monitor and the computer does not respound after 2 mnts when I start playing games online

  Hello

  1. what operating system is installed on the computer?
  2. what web browser are you using to play the games online?
  3. don't you make changes to the computer before the show?

  If you use Internet Explorer, then I suggest you to try the steps from the following link:

  The problems of games online using Internet Explorer
  http://support.Microsoft.com/kb/2528246
  
  Additional information:
  Why my screen is black when I start Windows 7?
  http://Windows.Microsoft.com/en-us/Windows7/why-is-my-screen-black-when-i-start-Windows-7

  Solve game problems
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-game-problems

  The problems of the game performance
  http://Windows.Microsoft.com/en-us/Windows-Vista/fixing-game-performance-problems

  Troubleshoot display with Microsoft games
  http://support.Microsoft.com/kb/263039

• CD drive does not open and the light does not work

  original title: single CD player problem

  The problem with my CD player seems to be unique I can't find an answer, or someone else with the same problem online.

  My computer is custom built, the CD player lasted me 1.5 years no problem, not until one day I realize, it does not open and the light does not work on it, I ordered a new drive and installed that one, still does not work. so, I replaced the SATA cable which connects to the motherboard, still does not.

  When I go to my computer the drive appears but when I right click > eject it says: "year error occurred while ejecting CD drive D".  It also appears in devices such as SCSI CdRom Device Manager but I am not sure if it's actually my CD player.

  I also tried troubleshooting http://support.microsoft.com/gp/cd_dvd_drive_problems and no solution.

  WTFFF ideas? I really hope that its not the motherboard

  There are two cables you need to connect to the drive, one for data and one for power.  You must connect both training at work.  If you only have the data cable is plugged and not cable power which would be a possible cause of the problem that you see.

  "Ryanb1290" wrote in the new message: * e-mail address is removed from the privacy... *

  Sorry, im just of knowledge about computer hardware.  you say that I should try a different agreement or another port to plug in?

  I tried to connect on a couple different SATA ports on the motherboard.