Satellite M30-704 slow start and IDE #2 0203 failure message after replace it

Similar Questions

• Satellite L300 - very slow start and freezes

  Hi all

  I have a Satellite L300, who treated me well - but more 2 months ago really slow and freezes quite often. I have anti virus, spybot etc and come up with nothing.

  Last night I tried to reformat the system by pressing 0 did not work so tried with F8 which I would like to make a longer scan but no reformatting. I am now very happy that I failed to do the reformat because I bought windows 7 after the initial purchase of the laptop.

  Any ideas anyone - or any person with same/simular problems?

  Hey,.

  This means that you have installed right now and not preinstalled version of Windows Windows 7?

  Well, in this case HARD drive recovery option is no longer available. You can do it on preinstalled only Windows.

  To format your laptop, you need Toshiba recovery disc.
  Did you create it?

• failure message after replacing the drive #2 0203 IDE

  My DVD is UJ - 820B and I replaced it with exactly the same.
  The dif is that the former is FW: 1.00 while the other is FW: 1.05
  1. is the only solution to fix the PIN? If Yes can you pls confirm with pins.
  2. the IDE #2 error means that: Bay DVD is on primary slave while the DVD is secondary master or vice versa?

  Can is it you further please let me know.
  If you wish to contact me by e-mail at [email protected]

  I guess that the CD/DVD drive supports another setting master/slave/c-salt.
  FDI #2 error is displayed because the BIOS can't recognize the drive correctly.

  The problem is that it of not possible to change these settings as on external drives by changing the rider a special internal firmware control these settings.

  You suggested that the reader is the same but the firmware is different.
  Well, in my opinion, that's a reason for the issue

• Satellite M30-704: band bandwidth hoggin?

  Hi This is my first post so go easy on me.

  I have a satellite m30 704 currently under xp sp2 and my problem is that I share a wireless network with two other computers, another laptop manufacturing running xp sp2 & a mac from apple OSX.

  The router is a netgear DG834GT.

  They are all connected via wifi & it seems to be my laptop creating the problem monopolizing the bandwidth?

  If I'm on the net at the same time as other portable computer manufacture it is not a problem at all, but if I'm on the net at the same time as the imac it takes literally 5 minutes to load a page on the imac.

  It happens also that as soon as I pass on the other computer laptop manufacturing & I am connected regardless of the fact that I'm not really surf the net?

  But if the XP laptop & the imac are both online at the same time there is no problem at all.

  I'm completely baffed to that I have absolutely no idea why this is happening, I even contacted netgear & they suggested upgrading the firware & reconfigure the router, done cela & still no luck so please can someone help me before I'm left with no option but also to buy a new laptop like the imac user is my brother who is a freelance graphic designer so that it uses his imac for work, hes, threatening to disconnect me!

  Thank you

  Hello

  A question: why you have connected two units machine to Windows XP and MAC to the internet if you only work with one at the same time?
  Disable the connection on Windows XP computer laptop for work with MAC and everything will be ok ;)

  I don't know why the Internet is slowly on other units while the Satellite M30 704 was connected to the WLan router. Maybe a part 3 application is running in the background and the bandwidth with both hands

  What card WiFi has been installed on the M30?
  It supports a 802.11 B or 802. 11A / B WLan standards?
  Maybe the map of the M30 WiFi signal has a bad influence on the correctly WLan signal received on the iMAC that knows

• Very slow start and run for Dell Inspiron 6400 XP times

  "I have a problem with an Inspiron 6400 brought to ' horribly slow start and run time.  XP Pro 32 bit SP3 patched up to date.  Cleaned up a lot of "undesirable", as the partially uninstalled programs, cleaned the files temporary etc. with CCleaner, cleaned and optimized the registry afer all the cleaning has been done, defragmented, tried to start without any of the boot files, disabled all unnecessary services and uninstalled virus checking software, (but ran several anti-virus controls) etc. - no help.   Safe Start Mode is faster, but... not at all normal - 1 1/2 minutes of screen to logon instead of close to 3 minutes.  A lot of memory (2 GB), which rises to 600 to 700 MB runnng all the stuff I've tried.  Hard drive is 1/3 used out of 120 GB with a 2 GB swap file.

  One thing I'm still scratching my head over - beyond the horribly slow boot - is very slow access to files even though everything seems to work normally, but as molasses in January.  Looking at the performance of the Task Manager tab when I run a copy of a file (whether via a cmd window or with Windows Explorer), I see a near max processor would be and the other with a small business.  Even if the customer says he had been getting worse for some time, after checking and cleaning of all things 'normal', my next thought was perhaps a bad disk or disk controller driver, but chkdsk ran very well (although it took hours) even if I ' d I have already updated all drivers (and even the DVD firmware and BIOS) on the Dell web site.  Oh, and I ran Dell Diagnostics (from bootable CD) updates all with no errors found.  And access to the slow file even with symptoms had max-processor occur with a copy of the file on a USB key that seems to eliminiate the hard disk, the disk controller and the pilot.

  The other interesting part of the display for a file copy task manager is that the processes tab simply shows System Idle 97 to 99%, with a percentage of casual for other processes as Explorer while I see 1 max out procesor on the performance tab.  That the same copy on your desktop shows 3-4% of the CPU usage and who is with active antivirus software.  I'm almost ready to fall toward a Windows reinstall, but would like to find the real reason behind this problem of puzzle...

  It of almost as if he's using PIO instead of DMA disk access, but... don't know how/where to test this.

  Look at:

  http://Windows-XP-tricks.com/direct-memory-access-DMA-on-IDE-hard-drive.php

  and

  http://winhlp.com/node/10

  Solved!   Thanks for the links, especially to each other.  An old but still a goodie!

  For those who have enquring spirits (and anyone else who stumbles across this thread), the primary IDE controller has been set to PIO and locked it.  Who would have thought that Windows slowly reduced the transfer speed, whenever he saw 6 errors on an IDE device until it has been reduced to PIO and then he locked it?  But the procedures described in the link of winhlp.com showed how to solve the problem.

  There are actually several problems that led to the final symptoms.  According to KB817472, the Atapi.sys has been improved in XP SP2 only degrade the speed of transfer on 6 consecutive errors instead of 6 cumulative errors.  And even though everything I have (Microsoft update) was seen and showed that this area was to SP3, I found that the driver for the controller layer IDE was the SP2 version.  Someone ran sfc previously perhaps?

  Oh, and I know now that the Task Manager process tab does not time processor kernal, but the performance tab.  Good to know...

  Thanks again to all who have responded.  Starting at the time of connection-question now is 40 seconds.   You'll love Untra DMA mode 5.   There is still a lingering question in my mind, since I've had the same symptoms of slow copy of a file on a flash drive.  Perhaps a link in some way to the way that Windows treats a flashdrive as a "drive"...

• XP system is extremely slow start and open programs are more inadmissible

  Is anyone know the problem / answer?
  My XP Sp3 has EXTREMELY slow start and programs are mostly non_responsive. When I close the programs they Peel the top of the screen down. Can you help me?

  * original title - screens XP Sp3 frozen, non-resonsive programs, peeling *.

  Hi dmahu,

  ·         Did you the latest changes on the computer?

  ·         How long have you been experiencing this problem?

  ·         What happens when you try to open the programs?

  ·         You receive an error message/code?

  ·         What security software you are using on the computer?

  ·         Do you have too many applications on the computer installed?

  I suggest you try the steps mentioned below and check if it helps.

  Step 1: Perform a clean boot to see if there is a conflict of software like the clean boot helps eliminate software conflicts.

  Note: After the boot minimum troubleshooting step, restore your computer to a Normal startupmode.

• Computer not starting and I get an error message

  After that I ran the microsoft of what free security scan it found some files that were Trojan horses that he couldn't get rid of, so I deleted manually solve them some of the problems that I had. The end of the analysis told me to restart my computer so I did. But now it will not start and I get an error message that says: "a problem has been detected and windows has shut down to prevent damage to your computer. Then he told me to check the virus and to ensure that it is configured correctly and run the CHKDSK command to check the alteration of the hard disk and restart my computer. How am I supposed to do all this if I can't even start up? I tried to go into safe mode, but the same screen comes up. He gives this technical information at the end of the message. STOP: 0x0000007B (0xF79E4524, 0xC0000034, 0x00000000, 0x00000000) if someone could help me it would be so awesome thank you.

  Hello

  Check the disk for malware:

  Create a Bootable CD with the Trinity Rescue Kit - free - which comes with 5 antivirus programs
  Integrable Hirem is another choice - more can be found using Google.

  Trinity Rescue Kit - download on top right of the page
  http://trinityhome.org/home/index.php?wpid=1&front_id=12

  CD of Hirem boot is another good choice
  http://www.hirensbootcd.NET/Download.html
  http://www.hirensbootcd.NET/CD-contents/138-HBCD-111.html

  Scan a Windows PC for viruses from a Ubuntu Live CD
  http://www.howtogeek.com/HOWTO/14434/scan-a-Windows-PC-for-viruses-from-a-Ubuntu-Live-CD/

  ===================================================================

  You can also save the data and re-install Windows 7. The hard drive can be set
  another computer as a 2nd drive (the best) or in an external USB enclosure. Either would allow
  allows you to copy the data to removable media such as CD, DVD or other USB drives.

  Or you can use a boot Ubuntu CD to back up data.

  Use Ubuntu Live CD to backup files from your Windows computer dead
  http://www.howtogeek.com/HOWTO/Windows-Vista/use-Ubuntu-Live-CD-to-backup-files-from-your-dead-Windows-computer

  ===================================================================

  For slightly more:

  BCCode: 7B 0x0000007B

  INACCESSIBLE_BOOT_DEVICE bug control has a value of 0x0000007B. This bug check indicates that the Microsoft Windows operating system has lost access to the system partition during startup.

  Important information if you have received a STOP Code

  If you have received a blue screen error, or stop code, the computer stopped abruptly to protect against data loss. A hardware device, its driver or software might have caused this error. If your copy of Windows is shipped with your computer, contact your computer manufacturer. If you purchased Windows separately from your computer, Microsoft provides support. To find contact information for Microsoft or the manufacturer of your computer connect with Support.

  If you have experience with computers and try to recover from this error, follow the steps in the Microsoft article solution STOP (blue screen) errors in Windows.

  The following actions could prevent a mistake like this does not happen:

  1. Download and install updates for your computer from Windows Update device drivers.
  2. Scan your computer for computer viruses.
  3. Check your hard drive for errors.

  Cause

  Bug INACCESSIBLE_BOOT_DEVICE control often occurs due to a failure of the boot device. During the initialization of the I/O system, the boot device driver could have no initialize the boot device (usually a hard drive). Initialization of file system may have failed because it does not recognize the data on the boot device. In addition, repartition the system partition or installing a new SCSI adapter or disk controller could encourage this error.

  This error can also occur because of incompatible disc material. If the error occurred in the initial configuration of the system, the system have maybe installed on an unsupported drive or a SCSI controller. Some controllers are supported only by the drivers that are in the library of drivers Windows (WDL). (These drivers require the user to perform a custom installation.)

  Resolution

  This error always occurs during the startup of the system. This error often occurs before the debugger connection, kind of debugging can be difficult, if not impossible.

  Fix a defective boot device: If a boot device is at fault, you must change the boot options. For more information changing these options, see Software Configuration on the target computer.

  Solve a problem of incompatible hard disk: If the installation program automatically detects the controller, you may have to skip the detection and the disc of the specific manufacturer allows to load the driver. Also, check the availability of updates for the firmware of the system BIOS and SCSI controller. Updates of this kind are usually available on the website or BBS of the hardware manufacturer.

  Delete all material recently added, especially of hard disks or controllers, to see if the error is resolved. If the problematic material is a hard drive, the firmware version of the drive may be incompatible with your version of the Windows operating system. Contact the manufacturer for updates. If you have removed another material element and the error is resolved, conflicts of port IRQ or i/o likely exist. Reconfigure the new device according to the manufacturer's instructions.

  Confirm that the hard disk drivers, hard disk controllers and SCSI adapters are listed in the list of the products tested Microsoft Windows market.

  If you have recently added a driver, restart your computer, and then press F8 to character-based menu that displays the choice of operating system. In the menu of Advanced Options , select the last known good Configuration option. This option is most effective when you add a single driver or service at a time.

  In addition, check your computer for viruses using any update, commercial software that examines the Master Boot Record of the disk hard antivirus. All systems of Windows files can be infected by viruses.

  This error can also occur due to corruption of the hard drive. Run Chkdsk /f /r on the system partition. You must restart the computer before the start of the analysis of disk. If you cannot start the computer due to the error, use the Recovery Console and run Chkdsk/r.

  If you cannot start the system in the last known good configuration, you should try to boot from the Windows CD. Then, you can run Chkdsk from the Repair Console.

  Warning   If your system partition is formatted with the FAT file system the long file names that use the Windows operating system could be damaged if you use Scandisk or another MS-DOS-based disk tool to verify the integrity of your hard disk from MS-DOS. Always use the version of Chkdsk that matches your version of Windows.

  If your system has SCSI adapters, contact the card manufacturer for updated Windows drivers. Try to disable sync negotiation in the SCSI BIOS, check the wiring and the SCSI ID of each device and confirming the proper termination. For IDE devices, define the IDE port integrated as primary only. Also check each IDE device for setting good master/subordinate/stand alone . Try to remove all IDE devices except for the hard drives. Finally, check the system log in Event Viewer for additional error messages that might help identify the device or driver that generated the error.

  BCCode: 7B 0x0000007B<-- read="" this="">
  * 1138.html? order = votes http://www.faultwire.com/solutions-fatal_error/Check-for-viruses-on-your-Computer-0x0000007B-

  =================================================================

  If you do not have a Windows 7 disc, you can borrow a friends because they are not a copy
  protected. The manufacturer of your system will also sell the physical DVD cheap since you already
  Clean Windows. You can also do an ERD on another computer.

  Try the Startup Repair - (if at anytime, benefit you from some, but not full access coming to Windows
  return and then try to startup repair.)

  How to start on the System Recovery Options in Windows 7
  http://www.SevenForums.com/tutorials/668-system-recovery-options.html

  What are the system recovery options in Windows 7?
  http://Windows.Microsoft.com/en-us/Windows7/what-are-the-system-recovery-options-in-Windows-7

  Try the disk Options recovery or Windows 7 startup repair.

  How to run a startup repair in Windows 7
  http://www.SevenForums.com/tutorials/681-startup-repair.html

  Also from the command PROMPT on the Console (if possible) recovery or a Windows 7 disc

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to fix the system files of Windows 7 with the System File Checker
  http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

  Then run checkdisk (chkdsk).

  How to run check disk in Windows 7
  http://www.SevenForums.com/tutorials/433-disk-check.html

  Retry After Chkdsk startup repair.

  If after those you can try the system restore to fashion without failure or the valuation or Windows 7
  disc.

  How to do a system restore in Windows 7
  http://www.SevenForums.com/tutorials/700-system-restore.html

  --------------------------------------------------------------------

  If you need to repair disks - these help repair Windows not re-install.
  Often an ERD will help you when the recovery disk does not work.

  Download Windows 7 system recovery discs - charge now $9.75 for ISO
  images to make the discs.
  http://NeoSmart.net/blog/2009/Windows-7-system-repair-discs/

  How to create a Windows 7 - free system repair disc
  http://www.SevenForums.com/tutorials/2083-system-repair-disc-create.html

  ======================================

  If necessary:

  What to do if Windows does not start correctly
  http://Windows.Microsoft.com/en-us/Windows-Vista/what-to-do-if-Windows-wont-start-correctly

  How to start on the System Recovery Options in Windows 7
  http://www.SevenForums.com/tutorials/668-system-recovery-options.html

  What are the system recovery options in Windows 7?
  http://Windows.Microsoft.com/en-us/Windows7/what-are-the-system-recovery-options-in-Windows-7

  How to do a repair installation to repair Windows 7
  http://www.SevenForums.com/tutorials

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• Continue to receive the KB928365 when I try to start it I get a failure message.

  OT: How can I get them to stop sending me KB928365?.

  Microsoft keeps clogging my phone with this update line.  It's for .net Framework v2, but my computer has only v4.  I get the update, and when I try to start it I get a failure message.  How can I get Microsoft to stop giving this gift?

  Hide it.

  1. click on start, point to all programs, and then click Windows Update or Microsoft Update.
  2. click on customize.
  3. Click to uncheck the box next to the update you want to hide.
  4. expand the update you want to hide, and then click the checkbox "don't show me this update again".
  5. click on review and install the updates.

  Information about the update: https://support2.microsoft.com/kb/928365/en-au

  Known issues that may occur during the installation of the update

  • You receive a Windows Update '0 x 643' error code or an error code Windows install "1603" when you try to install an update for .NET Framework 1.0, 1.1 or 2.0
    For more information about this issue, click on the number below to view the article in the Microsoft Knowledge Base:
    923100

    (http://support.microsoft.com/kb/923100/)

    When you try to install an update for .NET Framework 1.0, 1.1 or 2.0, you may receive Windows Update '0 x 643' error code or error code Windows install "1603".

  • You receive an error message "the folder 'Program Files' contains an invalid character" when you try to install an update to security for .NET 2.0 Framework
    For more information about this problem when you install an update to security on 64 bit versions of Windows Server 2003, click on the number below to view the article in the Microsoft Knowledge Base:
    923101

    (http://support.microsoft.com/kb/923101/)

    Error message when you try to install an update to security for .NET Framework 2.0 on a computer that is running Windows Server 2003 x 64 Edition: "Error 1324. The folder 'Program Files' contains an invalid character.

• Satellite M30 does not start

  I have a satellite m30 a little more than two years. When I used it one day it started making a "scratching" noise, he locked himself, when I stopped saying something about the emptying of readers (?). now it won't start at all, is simply the "scratching" noise Anyone know what it is?

  Hi deb_uk

  Generally, it should be a first think to try to boot from the CD and reinstall the operating system.
  To boot from the CD press the C key immediately after starting the laptop (push the power button)

• Satellite M30 don't start more

  Hello

  My Satellite M30 wont start... when I press the power button, the power led lights up, the cd light will blink once and then nothing happens...

  can certain a plez point me in the direction of Scripture?

  Help, please!
  thanx

  Cheerz

  Hello

  You know, without any of the detailed tests we can only suggest what might be wrong.
  I think there must certainly be a hardware problem because I guess that you can not see the start screen for Toshiba at the beginning of the startup procedure.

  It might be something wrong with the motherboard. I put t don't know if this helps but try to remove the power supply and the laptop AC adapter for several times. After 10-15 minutes, you could put the power supply in the notebook and connect the power adapter. Try to start.

  But if it doesn't help then in my opinion, a technician must check the device.
  Sorry for this general suggestion but I think it's the best way to know what's wrong.

• Satellite M30: Does not start XP

  My Tosh Satellite M30 laptop (with 2 HD discs) does not work after I have updated with the MS security updates, it does not start XP.

  The laptop makes a clicking sound and gives me the message:

  PXE - E61: Media test failure, check cable of
  PXE - M0F: Exit PXE ROM
  Operating system not found.

  I changed the boot order in the BIOS to: CDROM. And select Exit and save changes.
  Inserted my Toshiba Recovery windows XP version that allows me the option of
  "1. the recovery disc" or "2. Expert recovery mode"or also"Exit ".
  I chose "1. Recovery disc"as I'm not an expert (as you can tell!)

  I then get a load of diagnostic checks run by laptop and it shows then finally on the screen:
  X:\\ no disk fixed

  Ideally, I would like to repair and keep things I have on my drive D: HD.

  I'm pretty sure the XP starts on my drive C: HD.

  Your help is very appreciated!

  Suraj

  Hello

  The PXE message means that the device is trying to boot from the network. I put t understand you a lot with C and D HD. I assume you mean that you have two partitions on a single HARD disk. C partition for the operating system and the D partition for your data.

  If I understood you as soon as you cannot boot operating system at all. On this path, it is not easy to say what may be the problem but obviously you a problem with the HARD drive. It is probably defective. If the recovery DVDs is not able to detect one that there may be a serious problem.

  I put t know how contact the partner old Service your unit is but if the warranty is still valid and let check the device.

  Good luck!

• Satellite 2450-201: slow startup and shutdown

  I HAVE A SATELLITE 2450-201 AND I RUN ON WINDOWS XP HOME EDITION, I DID A REGISTRY CLEANER EVERYBODYS USERNAME USING REGISTRY FIX 5.5
  I HAVE DEFRAGED MY PC AND ALSO OPTIMIZED MY MSCONFIG STARTUP ITEMS AND EVEN THE BIOS UPDATE.
  THE RESULT IS EXTREMELY FASTER WHEN I CONNECT AND ACTUALLY UNDER WINDOWS BUT THE SAME OLD VERY SLOW STOP AND START TO WHAT I DO.

  THE WINDOWS BAR GOING ALONG AT LEAST 15 - 20 TIMES TO HELP START!

  Hello

  Maybe you've connected to some external devices to slow down the start-up procedure. You can also try to disable all the hardware components you n t need (modem. IrDA). Also check out which device is defined in a first start time (I hope that the HARD drive).

  For slow closing is responsible only running processes that should be forced disconnected. It all depends on your own configuration and you are using external devices.

• Satellite L550 - system slow start

  Hi people!

  Got a new Satellite L550 running Vista 32 - bit, everything seems fine except for a few things on this machine that goes like this:

  1 system restore is one hell of a long process I have ever met so far-time is gasoline and 17 GB of restore disks its really a whopper!
  2. If you have any trouble with the 'text leap' (when entering) so I have. Sound the Alps Touchpad I found must be configured (by disabling the tapping) that's if you can find the tab 'Advanced' in the properties of the mouse
  3. I tweaked my startup programs, but this machine, of course, happens to a slow start. Any help here

  Otherwise a pleasure to have abandoned another manufacturing in favor of elegant, intelligent Toshiba laptop and hopes that its evidence switch!

  Hello

  I had a problem of cursor jump as well, but that was my mistake... I touched the touchpad accidentally during typing...
  I could solve this problem by disabling the touch pad using the FN + F9 key combination.

  PS; You have the latest version of the BIOS? Isn't it? Then update.

• Satellite C650-1CN - no start and secure Windows 7

  Here's the problem:
  Satellite C650-1CN, after exactly 30 days Windows 7 blocked, and now push the power botton, the pc entirely, then start?

  Hello hans,.

  Wait a minute: what's the problem now?

  Can you start your computer and access the Windows?
  Or the computer does not start and you have a black screen only?

• 10.11.4 slow start and performance.

  Update caused 10.11.4 my iMac (27-inch, mid 2011) no start, after checking with an external start HD found no system errors, flawless HD, no failure of memory. Finally managed to boot into recovery and do an Internet re - install.

  Now I can't boot how whether it's very very slow, at least 10 Minutes, then well that just doesn't seem seem to work it is horribly slow. I was hoping it was indexing, but that doesn't seem to be the case.

  The question seems to be double, very slow startup and very slow performance. The external HD boot was 10.11.3 and seemed to be doing OK, so I have to assume that the question is 10.11.4 as everything else has been validated. All the usual things were made, PRAM, permissions etc.

  At this point I have nowhere to go. BTW, took me 15 minutes to get into this brief overview.

  I had problems with Bluetooth, you see only not my speaker MegaBoom and Photo Booth says "No. Camera connected... so I has the following guidelines.

  Downloaded and installed Mac OS 10.11.4 from scratch

  Then I reset the SMP:

  Reset the SMC on Mac desktops

  Follow these steps for iMac, Mac mini, Mac Pro and Xserve.

  1. Stop the Mac.
  2. Unplug the power cord.
  3. Wait 15 seconds.
  4. Reconnect the power cord.
  5. Wait 5 seconds, then press the power button to turn on the Mac.

  Reset the SMC a MacBook Air, MacBook Pro retina or the MacBook Pro with an internal non-removable battery

  This is how to reset the SMC on most modern Mac laptops, which none have a removable battery:

  1. Stop your MacBook Air / MacBook Pro
  2. Plug the power adapter to the Mac
  3. On the MacBook / Pro keyboard, hold down the command + Option + shift and the power button at the same time
  4. All the keys and the power button of output at the same time - the little light on the MagSafe adapter can change colors briefly to indicate that the MSC has reset
  5. Start your Mac as usual

  Keep in mind that by resetting the SMC you lose specific power settings, like the time he takes sleep a Mac and other customizations to the power settings. Not much, but if you have made many changes to your behavior of material you want to address things like behavior of sleep again.

  Boot time after resetting a SMC machines can be a little longer that usual, it's normal.

  Stop and start again, and this fixed everything for me...

  Robert MacAwesome88