Satellite M40: Recovery Procedure hangs on reboot after using the recovery CD

Similar Questions

• Satellite L450 - X 13 not turn on after using the recovery disk

  Problem climbed down after turning off suddenly. Initially could not get windows OS to work while I used the recovery disc. After it has been successfully used all of the computer has been cut and will not start (dead whole machine) despite the battery power and common alternative in place.

  When you press power button / stop the led green lights for a second and then immediately turns off, no attempt to start engine.

  Someone at - he seen this before or has any ideas?

  Remove the battery, disconnect the power supply, leave the laptop for now and try to start with power current only.
  The same thing happens again?

• Satellite P500 - loop of reboot after using the Toshiba Recovery disk

  Hello

  I have a problem recovery SATELLITE P500. I did the recovery disks. It starts ok on the recovery disk and format the hard drive and copy the disks to the hard drive. Then, he begins installing windows and restarts.

  He then goes to a loop
  (1) marketing and says "Setup is preparing your computer for first use.
  (2) Toshiba banner saying please wait... Second installation may take several minutes. Pleae do not interrupt or shut down the computer!
  (3) Windows logo
  (4) close...
  (5) restarts and goes to 1)

  It would be great if someone could help me with this.

  Thank you very much
  Softari

  Hello

  I noticed the same thing on my Satellite P500, but I must say it s not a problem, it of quite normal. The computer will restart several times (10 times or more) to complete the installation.

  You know that a lot of drivers/tools will be installed and some restart is required to configure everything properly.

  So don t interrupt the installation of recovery, just wait a little longer and a coffee. Everything is done automatically and your laptop is reinstalled with the factory settings. :)

• hang on reboot after using bcdedit/debug on

  Windows 7 Edition Home Premium.  Tried to set up the computer for debugging using bcdedit/debug on.  The system crossed the restart process after the Windows login screen, but hung on the screen 'welcome. '  Could not recover by using bcdedit/debug off; you had to use bcdedit /import to load a previously saved version of the bcd.  System rebooted and then until the end.  How can I find what is causing the blow and how can we get the computer to successfully start and enable debugging?

  Hi Carl,

  The issue of Windows is more complex than what is generally answered in the Microsoft Community Forums. Appropriate in the MSDN Forums. Please post your question in the MSDN Forums.

  You can check the link to post your question:

  http://social.msdn.Microsoft.com/forums/en-us/WinDbg/threads

  I hope that helps!

• XP unbootable after using the recovery disk, but Linux will be

  I have a laptop Toshiba Satellite L25-S1216. I had some bad virus, so I used the TOSHIBA Windows XP Recovery and Applications/drivers DVD provided with the computer when I bought it. I had used this once recovery DVDs or two before without problem, the last time was about 1 year ago. The recovery process seems to be okay: he seemed to format the disk and copy the files from the DVD to the hard drive. He copied about 5 600 MB hard disk for about 10 minutes and 40 seconds.

  But the computer does not boot from the hard drive after using the recovery DVD. I tried the process several times and it does not start in Windows XP on the hard drive. I checked the settings in the BIOs to make sure he can start, but it does not start in Windows XP on the hard drive. All I get is a white screen with a horizontal blinking cursor, nothing else, no error message, nothing.

  Then I got a copy of Linux (Fedora 14 live) on a CD and started on the computer from the CD R - W, DVD R drive. Then I loaded Fedora 14 hard disk. , I can boot into Linux (Fedora 14) of the fine to hard drive. In fact I use Linux to write this e-mail now. I also see the files that have been copied from the DVD recovery Windows XP on the hard drive, when I'm on Linux.

  Does someone has an idea what could be the problem? The only difference between now and the last time I used the recovery about DVDs a year, is that I had to replace it internal CD R - W, DVD R drive, as a mechanical part was broken. I replaced it with the same exact model (TS-L462) who was in the computer when I got it is new.

  Thank you

  B.

  Not sure how a restore xp cd may give you the option to start the recovery console.

  With a regular xp, recovery cd / repair console is launched all simply by selecting the 'r' on the configuration screen.  Subsequently, the recovery console opens and takes you to the drive prompt.

  In any case, what I suggest is to execute commands to drive at the command prompt that could make the drive bootable again.

  the commands are:

  Chkdsk /r

  Fixboot

  bootcfg /rebuild

  FIXMBR

  Normally, fixmbr running on a laptop is not recommended because it disables the hidden partition that contains the files for recovery.  Then re-enable it manually, is not easy. But since you have your on dvd, then you are lucky.

• Does not start after using the recovery Toshiba Tecra M5 - disk

  After using the restore on my Tecra M5 CD, the computer cannot even start!

  What to do in this situation?

  Hi jbdoktor,

  Does that mean exactly?
  Now, what happens if you start the computer?

  Sorry, but without this information it is difficult to help you. Maybe you should try the recovery again disk

• Should I update all the files from the Toshiba site after using the recovery CD

  I just used my recovery CD and update the Windows Update System.

  The question is: should I update all files in the files on this site download section as well?

  Usually after using the Toshiba Recovery CD everything should works and works correctly
  To my knowledge from time to time Toshiba has released new version of some tools or drivers. For example the BT stack will be developed all the time.
  But I think that if you have any problems with your system and peripherals, then you don't need t to update anything.
  Small is my opinion...

• My Aspire one 753 does not connect to WIFI after using the Recovery Manager.

  After using the recovery on my Aspire one 753 inbuild Manager my phone doesn't conect to wireless internet. I think the problem has something to do with the drivers, but I'm not sure. need help ASAP

  I used the live usb of ubuntu when I discovered that my network card was acutally one of Intel wifi card. https://downloadcenter.intel.com/Detail_Desc.aspx?DwnldID=24217&lang=eng&ProdId=3316. Thank you very much for your support on the issue

• Satellite A85-s107 - white screen at startup by using the power of the battery

  Satellite A85-s107 white screen at startup by using the power of the battery

  When I boot A85-s107 in battery power, it is get booted up in the background, but my screen is empty.
  After that if I connect it to AC power and switch deactivation/activation of the laptop power button, the screen comes back to life.

  There is no problem when I start upward when it is connected to an electrical outlet.
  Battery is fully charged and computer will work off the battery voltage if I remove AC after boootup

  Any suggestions?

  PS:

  also note that when I remove AC and then reconnect I start the computer on two occasions that it does not start the 1st time?

  Don t need to recharge the battery if the AC adapter is plugged ;)
  Try the tips posted by Alex otherwise it of a hardware problem, in my view, there seems to be something wrong with the motherboard...
  In this case, only the replacement could help and it could be a costly affair

• Spit Lightroom 4.3 when using the brush after using the red eye tool

  I bought Lightroom a few days ago. I was traveling so I didn't have the time to 4.3.

  The version shipped with the disk (4.1) worked like a dream. I downloaded 4.3 yesterday and I couldn't be sadder. First of all, I noticed that it cause the 'root' to use more CPU, which means that it does not use the CPU for Lightroom itself. More demand is usually and significantly slower than the original one.

  Today, I used the red eyes for the first time, and I can't just brush top unless it crashes! It is simply impossible. I rebooted. Upgrade my Mac OS 10.7.5...  No use. I even uninstalled and reinstalled again. I was forced to do all my first edit in there usinf the brush, then use the tool red eyes as the last step. But any time that I commit the brush after using the red eye tool, it crashes instantly

  It seems something funny on your establishment for sure that there is not a wide spread thing.

  What exactly is your establishment and where are the various files located - catalogue, images, etc.

• is it possible to save the Office XP for multiple monitors and restore after using the laptop in mobile mode?

  Is it possible to save the Office XP for multiple monitors and restore after using the laptop in mobile mode?

  Hi Kenelms,

  You can follow this link & check if it helps.

  HOW to: Set up hardware profiles for laptop computers in Windows XP

  Hope the helps of information.

  Please post back and we do know.

• Stupid question CS6. How can I get rid of my experience after using the quick selection tool?

  Stupid question CS6. How can I get rid of my experience after using the quick selection tool?

  The best way would be to make sure that your layer is not a background layer: click the lock icon in this case. Then click the icon at the bottom of the layer panel layer mask. This will create a mask that you can refine and not be destructive.

  

• Background layer unlocks and becomes the normal "no flat" layer after using the crop tool in PS CC 2015.1 (a different behavior for older versions of PS)

  Hi all

  I found that it is more difficult to explain than I thought

  I don't like the new behavior in the latest version of Photoshop (CC 2015.1) regarding the way in which the background layers automatically unlock and convert to regular layers after using the crop tool. It's completely different to how things worked in previous versions, where a background layer remained in locked state flattened after using the crop tool.

  I get a LOT of images and this change has added an extra step to each image that I harvest, because I flatten the layers after cropping before saving the image. I looked through the preferences but cannot find a way to change this new behavior. Am I missing something?

  Thanks in advance for your help

  See if checking Delete the cropped Pixels in the tool options makes a difference.

  

• I just make the payment for the license, after using the month trial. and when I want to use the programs and said that I must pay. and received e-mail confirmation of payment, that is not what I do

  I just make the payment for the license, after using the month trial. and when I want to use the programs and said that I must pay. and received e-mail confirmation of payment, that is not what I do

  
  

  Please see the links below.

  • Creative Cloud applications unexpectedly back in the test mode. CCM, CS6
  • Applications creative Cloud back in test mode after an update until 2015 for CC

  Also, make sure you use the right adobe ID to log in.

  Hope this will help you.

  Kind regards

  Hervé Khare

• Acrobat CC - lost Scripture I posted after using the fill & sign. Help, please...

  Acrobat CC - lost Scripture I posted after using the fill & sign. Help, please... It happened after I merged the two files...

  Hi mannys14196422,

  This problem has been resolved in the last update. Go help--> Check for Updates.

  Please let us know if you still face the question.

  Kind regards

  Sandeep