Satellite M45 won't start at all

Similar Questions

• Satellite L30 PSL33E won't start at all - the LED blinks 6 times

  Hello

  My poor mother is quite upset! Its Satellite L30 PSL33E just died.

  It completely off and now won't start at all.
  Orange light flashes six times when you press the power button.
  No hard drive, fan, screen or any other noise / activity.

  She tried without the battery.

  A kind of hardware failure, I guess.

  Any ideas what this blink code means?

  Thanks in advance,
  D.

  I put t know what the code means, but you can read it. short means 0 and 1 long

  In any case, the error code means that a hardware failure has been detected on the motherboard and motherboard replacement could help you?
  Why?

  because what is really hard to fix a motherboard for laptop very s.
  It especially not possible if you n t s have sufficient knowledge, experience, and special tools.

  I think that either you contact the ASP in your country and ask a difficulty or you'll have to buy a new laptop ;(

• Satellite Pro 2100 won't start at all - LED flash

  My SP2100 began to have feeding problems and now won't start at all. The AC adapter green LED is lit, that are relevant lights on the body of the laptop (although the "battery charge" light always orange these days). When I try the switch on, startup begins (in fact succeeded on occasion until this morning), however the battery indicator and the adapter lights are flashing, and everything stops again.

  On the rare occasions when I'll be past this stage, lights blinking, and the system soon shuts down again with a screen message "low battery." Until this morning, he would sometimes settle, the computer remained on, and the lights showed a State of equilibrium as usual.

  Initially I thought that the problem was of course the battery or the AC adapter, but now I'm starting to think that it is with internal PSU of the laptop (although I suspect the battery is probably tour after all this part of loading and unloading).

  Any ideas?

  Hello

  I think you're right. Flashing LEDS are a sign that hardware is defective.
  I can't say what exactly is the problem, this should be verified by a technicain.
  On the other side I don't know if it's worth to repair such an old machine.

  Good bye

• New Satellite P300 won't start.

  I hope you can give me some advice. This week, I bought a new Toshiba P300 GU with Vista Home Premium. It worked fine for about 3 days, but now it won't start at all.

  Symptoms:

  * - Some LED lights blink for a second, then they stop again.
  * - No fan or drive noise.
  I tried to remove the battery and power cables and left the computer for a day before trying again. There is no difference except for a few plus-lumieres LED flashes for a second, the first time I try to start the computer. The next time I try, only a few lights flash again.

  After I discovered the startup problem I noticed that food is quite noisy. I also noticed that the machine has a small mark RENS in the plastic in the upper left above the screen. (Looks like a defect of manufacturing error or transport) You hardly notice the 1 cm small inconsistency in the plastic, but it doesn't look like a normal scratch.

  As I thought that food could be the cause of the problems because of the strange sounds, I brought the maschine to a PC technician today. He tested the food and said it was working normally, but he also said that this should not seem like that. He did not open the laptop, to not cause trouble about the Toshiba warranty.

  I bought the computer to the Denmark I wanted a Danish keyboard. However, I live in Portugal, where I use the computer. Where is the PC now.

  Do you recommend that I contact an ASP to the Portugal to fix the PC or do you propose I have return the PC to the merchant at the Denmark?

  The ASP will be able to exchange the screen and power supply that are not in the State, they must be good obviously both?

  Thanks for the tips!

  Hello

  First of all I must say I never had problems after 3 days of my new Toshiba laptop but these things happen and no manufacturing activity is perfect.

  In addition, I agree with you. I would bring the laptop to an ASP because it seems that this motherboard is defective but I do not know Mr. it's only my personal opinion, and therefore the laptop should be checked by a technician for laptop.

  As far as I know that the laptop is covered by 1 year international warranty and so I would contact the ASP in your country. Ask them if they can fix your computer laptop and if not, you must communicate with other ASP where you bought the laptop.
  I think this is the best solution because they can tell you what to do exactly.

  Good luck and I m sure that your laptop will be repaired as soon as possible.

  Welcome them

• Satellite L500D won't start

  Hello

  My Toshiba Satellite L500D won't start.

  When I start my laptop lights three on the light green left, the two on the left are not green or red. I hear the coolingfan, no beeps at startup. When I start the laptop with a systemdisk is the same, nothing happens.

  I have contact the supportdesk and they said it could be the hard drive, this seems a little strange for me because I can't begin with a systemdisk.

  I hope someone can point me in the right direction

  Buddy

  Hello

  Unfortunately on this virtual path, it is not easy to say with certainty what can be the problem.
  It will be interesting to know what you did with your computer laptop last days.
  Have you installed some day or anything that may be responsible for the issue described?

  Update the BIOS maybe?

• Won't start at all. just a black screen. Only the satrts upward on safe mode

  Won't start at all. just a black screen. Only the satrts upward on safe mode

  Restore point:

  Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

  Try a restore of the system once, to choose a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

   

  If restore work not and you do not have a Vista DVD from Microsoft, do a repair disc to do a Startup Repair:

  Download the ISO on the link provided and make a record of repair time it starts.

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu.

  When you have changed that, insert the Bootable disk you did in the drive and reboot.

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  Link above shows what the process looks like and a manual, it load the repair options.

  NeoSmart containing the content of the Windows Vista DVD 'Recovery Centre', as we refer to him. It cannot be used to install or reinstall Windows Vista, and is just a Windows PE interface to recovering your PC. Technically, we could re-create this installation with downloadable media media freely from Microsoft (namely the Microsoft WAIK, several gigabyte download); but it is pretty darn decent of Microsoft to present Windows users who might not be able to create such a thing on their own.

  Read all the info on the website on how to create and use it.

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  ISO Burner: http://www.snapfiles.com/get/active-isoburner.html

  It's a very good Vista startup repair disk.

  You can do a system restart tool, system, etc it restore.

  It is NOT a disc of resettlement.

  And the 32-bit is what normally comes on a computer, unless 64-bit.

  See you soon.

  Mick Murphy - Microsoft partner

• Satellite Pro A300 PSAGDA won't start at all after flash Bios 1.90

  I have an A300 PSAGDA-01Y00R.

  I tried to Flash the bios to version 1.90. He started the process, and when I came back an hour later the cell phone was off.

  When you turn it on, it has nothing now. I tried removing the battery and running on sector only.
  Works for keyboard (as in light) and power works, but there is absolutely no action on the screen.

  Is there anything I can try?

  Hello

  Try this;
  Remove the battery, disconnect the adapter and wait 1 hour.
  Then connect both devices and try to turn on the unit.

  If this will not help, then you will need to contact a local ASP.
  It seems that something was wrong during the BIOS update process and therefore, the laptop can not initialize correctly.

  I put t see another solution for your problem

• Satellite L30 won't start - error below messages

  Can anyone help please? I have a satellite L30 & out of no where it does not start
  below error. I entered the bios & checked initialize preferences (disk HARD, ETC.)
  but all I get is the message below. I also tried a system restore, but nothing.

  For realtek RTL8139 (X) /8130/ 810 X PCI fast ethernet controller v2.13 (020326)
  PXE - E61: media test failure, check cable of
  PXE - M0F: Existing PXE ROM.
  operating system not found

  When I boot with the recovery CD in I get the message below

  Windows has encountered a problem... etc etc etc the usual windows bit.
  then

  status Oxc0000e9
  Info unexpected i/o error has occurred

  Thank you all
  Mark

  In my opinion, the HARD drive is certainly the reason why the laptop tries to boot from LAN.
  Yes, the laptop computer tries to boot from LAN and, therefore, the error message (PXE - E61: media test failure, check cable) is displayed.

  I think that a HARD drive replacement and the new installation of the OS will help you solve this problem.

  Greetings

• HP dc7600 xp pro won't start at all no safe mode, the monitor turns off

  HP dc 7600 does not start I have no disks.partition to install. (1) \\service 32 blah blah about 18 diferenent 32 files happen when I try safe mode to move forward, then lock tried new monitor I just need to get the safe mode to work

  First of all, please do not proceed with the bla, gloom :)

  If you can tell us exactly what you see, chances are that someone has seen and knows how to solve this problem.

  When you start mode without failure and the system crashes, which is the last line that you see on the screen (blah, blah should not be the answer).

  Tell us something about your system:

  What is your Version of XP and the Service Pack?

  Describe your current antivirus and software anti malware situation: McAfee, Symantec, Norton, Spybot, AVG, Avira!, MSE, Panda, Trend Micro, CA, Defender, ZoneAlarm, PC Tools, Comodo, etc..

  The question was preceded by a loss of power, aborted reboot or abnormal termination?  (this includes the plug pulling, buttons power, remove the battery, etc.)

  The afflicted system has a working CD/DVD (internal or external) drive?

  If the system works, what do you think might have changed since the last time it did not work properly?

  Have you installed a new hardware or software before this affliction?

  Was there something wrong before that lock in question, and to try to fix things, has taken a chkdsk or verification of disk errors?

  While you wait, I think you should make you a bootable CD from the Console of the Recovery XP (no XP media required) and get your started on that system and run a chkdsk/r from the XP Recovery Console.

  Here's how:

  If you have no XP bootable media (or aren't sure you have) create a bootable XP Recovery CD of Console and do not forget.

  This is not the same as recovery disks that might have come with the acquisition of the system store.

  You can make a bootable Recovery Console CD by downloading an ISO file and burn it to a CD.

  The ISO bootable image file you need to download is called:

  xp_rec_con. ISO

  Download the ISO from here:

  http://www.mediafire.com/?ueyyzfymmig

  Use a new CD and this simple and free program to burn your ISO file and create your bootable CD:

  http://www.ImgBurn.com/

  When you install ImgBurn, DO NOT install the Ask toolbar.

  Here are some instructions for ImgBurn:

  http://Forum.ImgBurn.com/index.php?showtopic=61

  It would be a good idea to test your bootable CD on a computer running.

  You may need to adjust the computer BIOS settings to use the CD-ROM drive as the first device to boot instead of the hard drive.  These adjustments are made before Windows tries to load.  If you miss it, you will need to restart the system again.

  When you start on the CD, follow the instructions:

  Press any key to boot from CD...

  Installing Windows... going to pronounce.

  Press 'R' to enter the Recovery Console.

  Select the installation that you want to access (usually 1: C:\WINDOWS)

  You may be asked to enter the password (usually empty).

  You should be in the folder C:\WINDOWS.  It's the same as the

  C:\Windows folder that you see in Solution Explorer.

  The Recovery Console allows base as file commands: copy, rename, replace, delete, chkdsk, fixboot, fixmbr, cd, etc.

  For a list of the commands in the Recovery Console, type help at the prompt of commands or read on here XP Recovery Console:

  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/recovery_console_cmds.mspx?mfr=true

  A good idea before you start things must first verify the integrity of your file system by using the chkdsk command.

  In the command prompt window, run the chkdsk command on the drive where Windows is installed to try to fix any problems on the afflicted player.

  Running chkdsk is fine, even if he finds no problem.  It won't hurt anything to run it.

  Assuming your boot drive is C, run the following command:

  CHKDSK C: /r

  Let chkdsk finish to correct the problems, he could find.

  It may take a long time for chkdsk complete or they seem to be "stuck".  Be patient.  If the HARD drive led blinks always, chkdsk is something.  Keep an eye on the amount of the percentage to be sure that it is still making progress.  It may even seem to go back sometime.

  You must run chkdsk/r again until it finds no error to correct.

  Remove the CD, and then type "exit" to exit the RC and restart the computer.

  You have not to set the BIOS to boot the disk HARD since the CD won't be.

• After having upgraded to Firefox 24 it now won't start at all after clicking on the icon. My OS is Windows Vista premium. It will start in safe mode.

  Upgrade to Firefox 24 and now nothing works at all despite uninstall it and reinstall several times and lose all my favorites etc. However, it does not start in safe mode. At first, I thought it was my Norton 360 Security, but after 2 hours in contact with them, I'm still in the same position. When I double click on the Firefox icon I see the moment where the cursor and then it disappears and nothing loads.

  My OS is Windows Vista Premium and I use Windows internet explore for the time.

  HELP Please!

  Thank you nellus91.

  I used the Microsoft Safety Scanner first, and it found nothing. I then used TDSSkiller and he found the problem.

  Problem solved.

  Thank you.

• Satellite C650 won't start - status: 0xc00000e9

  Laptop suddenly froze while I was on the internet.
  The mouse was still usable, but I could do nothing else — or even stop or restart.

  So I forced stop and tried to turn it back on, now it started, however, first of all, a screen will appear indicating "readers", and then I was faced with a screen with a list of writing on this subject.

  He said that I should contact the hardware manufacturer and known as the 'status' 0xc00000e9 and "info" as "an unexpected i/o error has occurred", I'm unable to boot up the laptop and have gone through the troubleshooting list.

  _ * HELP! * _

  Hey Buddy,

  You can start Windows in safe mode? Before you press F8 key to enter the start menu Windows Advanced to start Windows, and then select Safe mode. If you can start the computer, it seems to be just a driver issue.

  And before contacting an authorized service provider that I would try to reinstall Windows from Toshiba recovery disc. If you can test it with factory again.

• Satellite M35 won't start

  Hello

  I received a laptop from a friend who asked me to try and fix it. The problem, it seems to have is the following:

  When you press the power button, the phone begins to launch, the Toshiba logo appears on the screen as well as the message press F2 for Setup or other. Unfortunately, it is that he will.
  If I press F2, the text at the bottom of the screen changes to enter Setup... but in fact is not (and I left for a long time, just in case). The person who brought it tells me that she was burning a CD and the laptop has frozen, then rebooted and showed the same behavior since then.

  I tried a new set of RAM as well as to try to boot from a CD, neither of which he seems to want to do.
  If I press ESC just before that the laptop shows the Toshiba logo, the boot sequence appears and stops at mouse initialized (if this help anyone)

  I know that I could send the laptop into a Toshiba repair center, but they are trying to keep the cost of the repair from the bottom. The laptop is also two years is not eligible for the guarantee.

  Any help or advice on what to try would be great because I am all of these ideas!
  Thank you
  Steve

  Hello Steve

  I understand that this person doesn t want to help, but you must know that at some point there is not much to do. If you are not able to enter the BIOS setting there is something wrong with the machine.

  You can try to press F8 after starting up laptop to see what is happening, but as I said there must be a serious hardware problem. If nobody here can help you, please communicate with the service. No you don't have to give them a unit to repair, but you can just talk to them and see if the issue as it is known and how much the repair will be cool.

  Good luck and please keep us posting if you know more about it.

• Satellite M40x won't start after upgrade CPU test

  I have a portable M40x I took the CPU out of it to replace it with another to test the computer started fine then I stopped and took out and put it's original return CPU, and it wouldn't start. Now it primer with any one of all the CPU. When I turn on the power, all I get is a white screen for a few seconds and the laptop is closed down. Both the CPU is good because I since tested on other computers to make sure that this was not the problem.

  Anyone has any ideas on what is the cause?

  I m not surprised.
  As far as I know, Toshiba does not support updates, and it is not advisable to do something like that.
  It of one that the replacement of CPU on laptops is not easy and not recommended.
  The processors used in laptops are connected to the motherboard using a process called TCP (tape carrier package). It is a method of permanent connection and is used in the interest of miniaturization and heat dissipation.

  He was awarded the new heat paste? It s necessary and important if you want to connect again the CPU.

  It is perhaps a reason for not starting.
  I think more details you will get from the service guy in your country

• My Satellite L500D won't start

  Hello
  Really hope someone can help me. My dog was able to chomp through the power my laptop (while the laptop was turned off but plugged in). I managed to get the laptop to start on battery and everything was ok. I have a new power suppy (Toshiba official replacement) and when I plug it in the power light and the battery light is steady orange/red but nothing happens. I tried all the usual, remove battery type stuff but she just does not start.
  I would have thought that I had done something important, if it wasn't the fact that it worked very well until the battery was low.

  Would appreciate it really all suggestions, she is only 14 months old so I hope that this is not a great case of the laptop case in heaven :-(

  With regard to the dog!

  Hello

  What is the voltage and amperage of this new adapter? Is this the same mark as based on the laptop?

  What exactly happens when you press the power button?

• After that Vista update of my Satellite L40 won't start

  After automatic Vista update of my boot of t n for laptop and the screen is black. Using the F8 key I have the advanced startup options, but none of them helps. The screen remains black. Hard drive led is always off.

  I have Satellite L40. I restored the OS using Toshiba drive. All data has been lost. After 2 or 3 days, update has been installed again and I noticed the same problem. What can I do?

  Please help me!

  For me, there is only one option: disable the automatic update to Vista.

  By the way: when that happen, have you tried to boot the operating system in safe mode and roll back OS to an earlier time using System Restore tool?