Satellite M60: Little or no connectivity with the Modem cable

Similar Questions

• What is a substitute for the migration assistant? I tried in vain for three hours to migrate files from a macbook pro to each other so that even if connected with the ethernet cable the computers never see each other.

  What is a substitute for the migration assistant? I tried in vain for three hours to migrate files from a macbook pro to each other so that even if connected with the ethernet cable the computers never see each other.

  You can connect otherwise?  USB or FireWire or love at first sight?  You can connect both machines and start the one you want to transfer to target disk mode.  If your other machine is up and running with an account on it and you just want to move files, you can simply drag and drop the FRO the machine mounted TDM, or you can use the migration wizard.

  Or, if the other machine still starts and runs, you can start both computers and connect to the same wifi network and share the hard drive like machines on the network.  Access them in the finder on the new machine files and drag-and - drop, or use the wizard migration, on wifi.

• Satellite C660 WIFI does not connect with the channel 1 of the router

  Hello

  I have this problem for several months. I connect my laptop with the D - link DIR-615 as a WAP browser.

  I can't remember, but the fact is that I can't connect more with channel 1 of my WAP.
  Connection with the other channels is no problem.

  Other laptops or the available have no problem connecting to channel 1.
  He's tried a recovery, remove and reinstall the driver for my WIFI.

  All know what to watch?

  Kind regards

  Jacky Deschepper

  Where have you changed channels settings: within the router or the wireless network adapter?
  Is that it s any laptop you are using. It s always a matter of the WLan card that is integrated.

  Usually, you can change the Wlan card settings in the properties.
  Go to Device Manager-> Wlan card-> right click Properties-> Advanced tab
  Here, you would be able to change the available settings.

• Problem with TC loss of connection to the modem cable

  I have a TC of 2 TB which is connected to my ISP provided by cable modem. It worked fine for 3 months after the installation in December, but now all of a sudden it will lose its connection to the modem and we lose our wireless internet. We have replaced the modem cable and it does not solve the problem. I have to reset the TC 2 - 3 times a day. Nothing else has changed recently with regard to the network set up. that only changes were to specific devices that use the wifi connection, and this was always something changing, depending on the devices we use. Any thoughts? I'm not a savvy person tech, BTW.

  We need to ask a few questions in order to learn more on what the possible cause of the problem might be.  Please be patient with this. Thank you.

  What is the number and the model of the modem you are using right now?  We ask because some modems work better than others with Apple routers, and even if you have changed the modem, it could still be a model who does not get along well with the Apple router... or... you could say that the router from Apple does not get along well with the modem.

  How old is the TC? We ask because the life expectancy, on average, a time capsule is about 3 years.  After that, they tend to start losing connections to an ever-increasing rate.

  Who is your provider of Internet (ISP) Service?  We ask because most suppliers are in the active process of implementation of a new type of connection called IPv6 in their systems... and despite ISPS claiming that their system changes should cause no difficulties connection or interruptions system... which doesn't seem to be the case at all.

  We have seen an unusual number of reports from users who suddenly have problems with their ISP connection, when things were very well for many months before. That points directly to the IPv6 changes that ISPS are doing as the culprit. In some cases, there could be way to work around the problem, and in some cases, there is nothing to do but wait as the ISP to complete their changes and be everything to speed.

• Unable to connect with the modem router e2500

  I have an old Speedstream 5100 modem hooked to my router e2500. Everything works well except if for any reason any my modem disconnects from the ISP I can not log in via the route to reconnect it. I need to connect a cable modem to computer direct run connect script then modem plug in router all is well again.

  Any ideas why the connection to the modem router is blocked?

  Thnaks,

  Al

  al_mathews wrote:

  My Speedstream has only an Ethernet connection so I did not know that he resembled a router for the local network. I changed the mode of bridge on the PPoE configuration on e2500 / Speedstream and reconnected to the ISP on the e2500 configuration screen. Who can solve the problem of reconnecting from now, it is run on the e2500.

  One thing I see now is since I left the modem IP set to 192.168.0.X can't do it all through the e2500. Is it because my DHCP in e2500 is configured with 192.168.1.X range IP modem is not covered in my network? If I directly connect Speedstream and place you IP 192.168.1.X will become visible on LAN?

  You are unable to access the modem even if you have a PPPoE connection. For PPPoE the E2500 will not need an IP address from the modem so it does not have DHCP on WAN port and so we never see. When you try to access the address of 192.168.0. * the E2500 it will route through the tunnel PPP to the ISP.

  If you connect your computer directly to the SpeedStream it should automatically get a DHCP address (assuming that the computer is still ongoing on the DHCP protocol and not with a static IP address and the SpeedStream does not automatically neutralize the DHCP server in Bridge mode). If you have configured a static IP address on the computer, you must change the IP address to an address of 192.168.0. *.

• Pavilion dv7 Notebook - how will I know if I'm connected with the Ethernet cable or wireless?

  The notification area icon displays only a wireless connection, although the ethernet cable is connected to the laptop.  HP Connection Manager shows that both wired and wireless connections are active.  All of my previous laptop (not HP) had different icons for wireless to a wired connection in the notification area.  HP has a different icon for a wired connection?  If so, why it doesn't show in the notification area?

  obxperson99 wrote:

  Enrico, thank you.  I have installed Win7 Pro.

  The Network and Sharing Center says I'm connected wireless.

  Program of HP's "Connection Manager" shows that both the wired (ethernet) and wireless networks are connected.

  If I am always connected wirelessly with the ethernet cable plugged into my machine, how to move from the wired connection?

  Open the network and sharing Center. Look at the picture of what I have posted. Do you see where it says log in or out? Select it, and then disconnect from the wireless network. If you are also connected to the wired connecttion, then the connection should be almost transparent.

• Will be a docking station for the earlier works to connect with the lighting cable, if I have a match?

  I have a really great dock I want to use it with my new iPhone. but he has the old type of connector. If I buy an adapter, it will only load, or it will play music from the phone as well?

  If you buy an authentic Apple adapter, this should work, although I saw some errors with a 30-pin lamp CAP in my car for the connection of the iPod.

• NB100 - unable to connect with the ethernet cable

  My netbook works very well with the wireless connection (even if I get only 4 MB when I have 10 MB connection). I visited a House of friends the other day and she does not have a wireless router.

  I plugged the cable broadand on my machine. I disabled the wireless connection and activated the network connection in network connections. I turned off then the feature wireless on the keyboard with the keys Fn & F1.

  It shows that there is a link in my taskbar, but when I try to open the internet it does not connect.

  I thought it was his connection because she had problems so today I went to another friends house and got exactly the same response.

  I decided to try the same thing at home and I disconnected the ethernet cable from my wireless router and performed the steps listed above.

  Still no joy - am I missing something?

  Tips:

  Use a static IP address, and not using DHCP.
  Disable your firewall. It can block the network connection.
  Disable network cards won't do not. If you use wired LAN, turn off wireless and Bluetooth in the Device Manager.
  Check if their ISP requires a power of Attorney, if they don't, specify the Proxy and Port in your browser settings.

• iTunes does not list my ipod touch when I connect with the USB cable

  I bought an I - pod and put in place, but when you plug the USB cable, I-Tunes does not show the unit. Just down loaded music in my computer for the I - Pod so that it is on that point.

  Hello

  You use the Apple software (iTunes) and Apple (iPod) hardware.

  You must contact the Apple Support.

  "IPod Troubleshooting Wizard.

  http://www.Apple.com/support/iPod/five_rs/

  Or the iPod of Apple communities.

  https://discussions.Apple.com/community/iPod/Ipod_touch?CategoryID=221

  Or ask iTunes Support.

  "iTunes support-how to use iTunes.

  http://www.Apple.com/support/iTunes/

  "Contact iTunes Support.

  http://www.Apple.com/support/iTunes/contact/

  Or ask in the community Apple iTunes:

  https://discussions.Apple.com/community/iTunes

  See you soon.

• [WAG200G] problem to connect to the modem cable Alloys Atlanta Dcp2203

  Hi all!

  I recently got my new cable internet access (I used to have DSL) and I want to use my WAG200G to distribute internet by air.

  When I connect my laptop to the Dcp2203 of Atlanta Alloys via ethernet, I get an external IP (200.XXX.XXX.XXX). I need to adjust my ethernet interface get ip dynamically to achieve this.

  Now I need to connect Dcp2203-(ethernet)---> WAG200G - wifi---> portable

  How can I configure my WAG200G to work using this structure?

  Thanks to you all!

  You can't really use your WAG here. You will need a router ethernet, not a DSL router.

  The only thing you can do is use the WAG as access point and connect the laptop directly to the internet. This works as long as you don't want to connect a device to the internet at any time. You will not be able to connect 2 or more at the same time, because your ISP only allows you to have an active connection at any time.

  To set this up, you will need to connect a computer to the WAG. Open the web interface of the WAG to http://192.168.1.1/ to first set up your wireless network (SSID, enable WPA2 Personal Security with AES encryption and a password strong change). Disable the DHCP server on the main settings page.

  Then one of the ethernet wire ports of the WAG in your modem cable. Now you can connect wireless to the WAG and the WAG access to the internet and the modem. New: your computer will have direct access to the internet and will have a public IP address. You can't have two active connections at the same time.

  If you need to make changes on the WAG, you set a static IP address on your computer, for example 192.168.1.2 with subnet mask 255.255.255.0. Then you can access the web at http://192.168.1.1/ interface when you have completed your changes, go back to the DHCP/Auto IP on your computer.

  Otherwise, you should get a router, for example Wireless Linksys WRT routers.

• N300 EX2700 does not connect with the modem

  Trying to install EX2700 N300 range extender, but the link never seeing device, not with modem connection. I even hung it with cables ethernet right now, and it still does not connect. Any suggestions?

  No, he didn't. But a few days later, a wi - fi network "Netgear_ext" appeared in my ads. I started playing with it, then I could access the Web activation page. I still don't know how I did it, but eventually it worked, and he has now set up and solved my lack of power of the signal of the TV farthest from the router.

• My Windows XP laptop does not connect to my 2WIRE router wireless, but do my other laptops. It will only connect with the ethernet cable. What is the problem?

  What I'm doing.

  1. my laptop is a Toshiba XP

  What serial number and model of Toshiba?

  What type of encryption 2wire router uses for now? Type of WEP or WPA? If the latter do you know if your XP laptop wireless card supports WPA (some older cards only). If you find that this is the problem, you can go to the WEP encryption or buy a WPA compatible device to use instead of the current device on the XP laptop.

  If you don't know how to find this information...

  The range and the model are probably on a sticker on the bottom of the laptop.

  I think that there is a sticker on the side of 2wire routers (leastways are those provided by BT) gives you the encryption key and this might also state what is the type of encryption. Or, if not, open a web browser such as internet explore/firefox etc and go to http://gateway.2wire.net, somewhere on the router admin pages, you will find information on wireless security/encryption.

  Regarding the card laptop wireless, I can help with this if you give me the range and the model as requested above. I can, also, be able to determine from the description of the device in Device Manager. Click Start, click Run, type devmgmt.msc and press ENTER. Network adapters (click on +) and transcribe the wireless adapter that there are listed in a response to this post.

  Tricky

• My Sprint HTC Android mobile phone connects with the supplied USB cable, but the computer says 'No HTC Device Connected'

  My Sprint HTC Android mobile phone connects with the USB cable, but the computer says 'No. HTC Device Connected' so I can't sync...

  Hello

  1. do you have HTC Manager installed on the computer?

  2. have you tried it with different USB ports?

  You need the HTC Sync HTC phone Manager software.

  Method 1: Try again with different USB ports and see if that helps.

   

  Method 2: If HTC Sync is installed, if you get the message "no device connected" in HTC Sync, ensure that your phone USB setting is changed to "Charge Only" to "HTC Sync".

  If the methods above do not help, you can contact HTC for additional help.

  Here is the link: http://www.htc.com/us/support/

• BlackBerry Torch 9860 smartphones does not connect with the pc via the USB port.

  We have a new Torch 9860 which does not connect with a PC via the USB port.  What should do?

  SlaKir wrote:

  The answer is YES

  Well, then your USB port is likely.

  Restart the PC and BlackBerry (with smart BlackBerry power onthe phone, remove the battery for a minute and then reinsert the battery to restart).

  Then, connect with the USB cable and a rear main USB port at the back of the PC, not a front USB port.

  Hear a ringing or sound from the PC indicating that the BlackBerry is connected?

  Start the BlackBerry Desktop Manager software. Give it a minute to recognize the connected BlackBerry device... you see the code PIN of BlackBerry on the PC in the BlackBerry Desktop software?

• Satellite M30X-129 loses connectivity with the external USB device

  I have a problem with my laptop that has regularly been do worse and I can handle is no longer!

  Whenever I work with external devices via USB ports (all kinds of devices but my external hard drive Smartdisk CrossFire and my iPod in particular), after a certain period of time (sometimes minutes, sometimes hours) the laptop loses connectivity with the device.

  If happens to be listening to the music, download photos from a camera or laptop computer for the ' net or sync of the iPod, the connection is cut off, turning off the device and I have to start all over again!

  I'm almost at the point of launch of the laptop by the window, so any help is most welcome.
  Thank you
  Abderrahman

  Hello

  This happens also with the external USB mouse?
  This occurs if the power adapter is plugged or only if the laptop running on battery?

  In-hubs properties > Device Manager USB root-> power management
  You will find the option called allow the computer to turn off this device to save power.

  I would recommend the brand and disable this option.

  Maybe it helps.

  By the way; When do you update the operating system? I think that it s there long time, perhaps some system files or registry entries are corrupted or a 3rd party application affect the USB functionality?