Satellite M60: USB devices do not work

Similar Questions

• USB device does not work

  Original title: I can not use my USB, this legend is displayed: "Please insert a device", what can I do?

  It is installed as always, but when I want to use it or open it, it says "screwed a disco en Unidad extractable: (G)" Please help!

  Hello

  1 have you ever done any recent hardware or exchange of software on your computer before the show?

  2. What is the brand and model of the USB device?

  3 is the issue limited to any particular device?

  Please follow the methods and mark the question below:

  Method 1:

  Tips for solving problems of USB devices:

  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-solving-problems-with-USB-devices

  Note: This also applies to the Windows 7 operating system.

  Method 2:

  Open the hardware and devices Troubleshooter:

  http://Windows.Microsoft.com/en-us/Windows7/open-the-hardware-and-devices-Troubleshooter

  Method 3:

  Uninstall and reinstall all USB controllers and check.

  a. press the Windows key + R simultaneously to open run, type devmgmt.msc and click OK.

  b. in the Device Manager, double-click Universal Serial Bus controllers to expand and right-click on each of the controllers and click Uninstall.

  c. restart the computer and install USB controllers in Device Manager right click on Universal Serial Bus controllers and click on Search the hardware changes.

  I hope this helps.

• Satellite C650 USB ports does not work

  Hello

  I have trouble with me laptop C650. USB ports yesterday do not work after you connect USB stick, SD card or some.
  Now I don't know if it's a hardware or software error.
  I tried to restore the system, change the USB drivers, perform the maintenance of PC and check the antivirus, but nothing did not work.

  Laptop computer ads?

  Thank´s for more info...

  Hello

  You can try to refresh the USB ports and the controllers that appear in Device Manager.
  Disconnect all USB devices and go to Device Manager.
  Here, expand USB area controllers.
  Now delete all USB host controllers and hubs root USB in the list.
  After this reboot of the laptop.
  Finally, the Windows operating system should start and should recognise all USB devices once again. Now connect a USB mouse and check if you can use it.

• Satellite A300 - USB drives do not work!

  I have a satellite A300 and it has 1 usb port on the left and 2 on the right. The one on the left works perfectly well, but both left work at all which is really irritating.

  When I try and use the 1st, a bubble pops up saying: peripheral USB not recognized and when I use the 2nd one nothing happens at all. Ive downloaded the lates bios update, but it did not work.

  Help please!

  Have you updated the chipset drivers? Here, you will also find Toshiba Europe site where you downloaded the latest version of the BIOS.

  It could also be a hardware problem, but first of all, I would like to try a recovery facility. If you have the recovery disk try this.

• PowerEdge 2850 message error, no display, usb devices do not work and all readers are off (a little)

  Hello! I'm here in the dell community because I'm having an error with a PowerEdge 2850 server. When I boot it all seems to work, but inspection closer both blue and yellow led on the front is off. All devices (such as a keyboard) will not turn on. Supplies seems to work perfectly well with the error led out of power and both of the Green led on the power supply on. The drives at the front lights up but then after 2 seconds the led for every hard drive goes off and then when you reconnect the drives it will be on for 2 seconds then turns off.

  I tried:

  Reset all RAM chips and CPU in the case

  Replugin all hard drives from the server

  I tried multiple monitors

  has tried just using the power supply instead of the power brick or a surge protector

  and tried to run it only out of a raid, everything ends up in the same result

  I have no idea what to do so im just going to ask the community of dell. Thank you!

  Hello.

  What is the error specific are you? Try the system at least to the POST with the following components:

  • System Board
  • Processor
  • A bar of memory in DIMM1-A or B-DIMM1
  • Power supply
  • Riser
  • Control Panel and bottom of basket (necessary only when the last power state was off. Ensure that all USB devices, including the keyboard are disconnected.

• Satellite L750D - USB Ports do not work

  Hello

  a couple of days all three of my USB ports stopped working.

  I tried several USB devices and none make their appearance as being connected at all (check start > computer > devices with removable storage).

  The two on the right side of the laptop have never really worked systematically earlier and there again, but the left hand, we worked more or less all the time.

  If anyone can help that would be great
  Thank you

  Hello

  Have you tried to remove and reinstall the USB host controller driver in the past?
  If this isn't it.

  Go to Device Manager and expand the controllers Universal serial bus tree
  Here, the Generic USB hub and the USB universal host controller.
  Delete all of these devices from the list of devices and reboot the laptop.

  Usually once the system has booted, all devices removal must be found and resettled automatically. Wait until the end of this procedure and connect the USB device (ie the USB mouse) to USB port just to check the functionality.

• Satellite M40: USB Audio does not work properly in ACPI mode

  Hi all
  I just bought a laptop Satellite M40 whose purpose is to be used as a portable audio system.
  For this, the USB audio devices are an excellent solution.

  Unfortunately, although it was working properly when recording (sound is perfect with all devices compatible USB Audio, I have tested), there is a problem in reading that I had a lot of clicks and POPs.

  After a lot of research trying and google, I solved the problem by changing the computer ACPI PC Standard mode.
  This is a workaround.

  But this way, I don't remember what my status of battery, and my laptop does not shut down automatically.
  Actually, my laptop is no longer run as a laptop :(

  I suspect a very serious problem in a Toshiba components management. In particular, I wouldn't be surprised to be told that freeze the cords of some regular system of court management, and therefore the 10ms buffers audio USB fall in against the recess.

  This would be so much bother me if I were not part of the technical support team of the company that launches also a few new audio USB products who will not fail to work correctly with laptops.

  My question is:
  Is there a driver / updating bios that gets rid of this problem?
  If a person of Toshiba technical support to address this issue directly with me, I'd be happy to help, as I am personally and professionally concerned.

  Thanks in advance.

  [Edited by: admin]

  Hello

  I put t know what USB audio device you use, but most of the USB audio devices cannot use the USB power. These devices have need of an external power supply of A.C and especially this external power supplies are delivered with the USB audio device.

  Also, I read on some sites that the pop occurs sometimes due to non synchronicity of the modules different buffers or / and of the use of certain applications in parallel.

  The computer ACPI PC Standard mode change is one of the many solutions and proposals
  You can check some patches from Microsoft. Check if all updates from Microsoft are installed.
  Also change the performance options in the options of the system to adjust for best performance.
  Disable Windows messenger.
  Virtual memory should be set to custom size and initial size and maximum size must has the same value (ie. 512/512)
  In the system.ini should the vcache is also the same: MinFileCache = 16384, MaxFileCache = 16384
  Disable the peripherals such as scanner, printer.

  As you can see, these issues could occur on all computers (desktop and laptop) and it s is not a problem of Toshiba. Also, contact the manufacturer for support external audio device and detailed information.

  Good luck

• "USB device not recognized" error keeps popping up and USB devices do not work

  I receive the error USB not recognized on my HP Vista laptop at home.

  For anyone else who might have this problem until I make this comment and you run windows 8.1 there is an update that fixes it!

  http://support.Microsoft.com/en-us/KB/3013769#fixed_issues

• I get message "USB device not recognized", but two USB devices are actually works very well. Poster sometimes Device Manager 'unknown device', then it will disappear and reappear.

  Poster sometimes Device Manager 'unknown device', then it will disappear and reappear with the error message.  Sometimes, I see the message even when there is nothing in the USB port.

  Hi malsnano,

  I see that usb devices do not work on xp. I'll help you with this problem.

  1. What is the brand and model of the computer?

  2. what security software is installed on the computer?

  3. have you made changes on the computer recently?

  4 is the issue limited to these usb devices?

  Method 1:

  Run the fixit from Microsoft Fixit article and if that helps.

  Hardware devices do not work or are not detected in Windows:

  http://support.Microsoft.com/mats/hardware_device_problems/en-us

  M odes 2:

  Put the computer in a clean boot state, then check if that helps.

  How to solve the problem by performing a clean boot state:
  http://support.Microsoft.com/kb/929135

  Note: Once you have completed troubleshooting, perform the steps in step 3: to reset the computer as usual.

  Method 3.

  Run a full scan of the computer with the Microsoft Safety Scanner to make sure that the computer is virus-free.

  Microsoft safety scanner: http://www.microsoft.com/security/scanner/en-us/default.aspx

  Warning of Security Scanner: there could be a loss of data while performing an analysis using the Microsoft safety scanner to eliminate viruses as appropriate.

  Method 4.

  You can disconnect all USB devices and then perform the following steps:

  1. click on start and then click Control Panel.
  2. click on system and Maintenance, click System, and then click Device Manager.
  Note that if control panel is in Classic view, double-click System and then click on Device Manager.
  If you are prompted for an administrator password or a confirmation, type the password, or click on allow.
  3. in Device Manager, double-click to expand the "USB Bus controllers", right click on the controller host, click "Uninstall" and click "OK".
  Check that if at all, there is an exclamation point on the pilot, it suggests problems with the installed driver.
  4. Repeat step 2 to uninstall all items under 'USB Bus controllers'.
  Then, restart the computer and Windows XP will automatically reinstall all USB controllers.

  Let us know if you need assistance with any windows problem. We will be happy to help you.

• Ethernet USB adapter does not work after update to sierra mac

  Ethernet USB adapter does not work after update to mac sierra.

  Please solve this problem as soon as POSSIBLE

  Hello guatamshah,

  If your USB to ethernet adapter does not work now that you have upgraded to Mac OS Sierra, there are a number of things we can try to get it working again.

  The first thing we want to do is to reset the SMC and the NVRAM on your Mac.
  Reset the management system (SCM) controller on your Mac.

  https://support.Apple.com/en-us/HT201295

  How to reset the NVRAM on your Mac.
  https://support.Apple.com/en-us/HT204063

  If the adapter is not still work after only two resets check to see if your Mac recognizes the device properly in the information system. In the Apple Menu, choose about this Mac, and then click the button 'system report... '. ». Once you have the window open system information, see the USB category on the left.
  OS X: about system information and System Profiler

  https://support.Apple.com/en-us/HT203001

  If she does not appear in the information system, see the articles below.
  macOS Sierra: If a USB device does not work

  https://support.Apple.com/kb/PH25343

  macOS Sierra: check your device's USB connection

  https://support.Apple.com/kb/PH25567

  However, if you do not see the device in system information, you may need to verify that network service appears correctly. In the Apple menu, choose system then Network preferences. You should see an entry similar to "Ethernet" on the left. If no, see the steps in the article below to add. Once add, test to see if your connection works with a disabled Wi - Fi connection.

  macOS Sierra: Add a network service
  https://support.Apple.com/kb/PH25279

  If it does not appear in the network, please let us know what you see on the right when you select the service, and the name of the service as it appears and we can go from there!

  Kind regards.

• HELP - All the USB device does not not - Vista Ultimate

  I have a desktop P4 computer and ran on Vista Ultimate for more than 1 year (window updated constantly). Everything worked smoothly until one night, all my USB devices don't work anymore. Based on the Device Manager, the USB are ok, check my BIOS, everything remains unchanged.

  now, I got tired of reinstalling the same operating system and at the end of the installation, all USB devices do not work.

  Please can someone advise what should I do to recover my devices USB working again.

  It is the motherboard or the operating system has problems?

  Hi Dragon,.

  Follow the instructions below and check whether it is hardware or operating system issue.

  Tips for solving problems of USB devices
  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-solving-problems-with-USB-devices

  Check whether the problem is resolved.

  If this does not work, you can try to update the chipset drivers and see if the problem is resolved.
  Looking for drivers
  http://Windows.Microsoft.com/en-us/Windows-Vista/finding-drivers-what-to-do-when-your-hardware-wont-work-with-Windows-Vista

  If the problem persists, contact the manufacturer of your computer to update BIOS that may help you resolve the issue.

  BIOS change / semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

  You can also check out the link below.
  Rollup cumulative update for USB in Windows Vista Basic components
  http://support.Microsoft.com/kb/941600

  Please post back and let us know if it helped to solve your problem.

  Kind regards
  KarthiK TP

• Satellite M50D - Has: devices of USB 3.0 not working in USB 3.0 ports

  I use 2.0 devices in the ports of 3.0 fine, but my 3.0 Flash Voyager USB3 8 GB device will not work. It connects then disconnects once, not appearing is not in the Device Manager to all.

  I tried to install the USB driver out this version of the site 2.0.10.273 - 130101 has for my model. It made no difference.

  Install Windows 8.1 system

  Any ideas? Thank you.

  You are able to use this USB through a USB 2.0 port?
  Check it out.

  But at this point its not easy to tell if its USB device issues or problem of USB port.
  If other external USB 3.0 devices work properly in the frame of your laptop, the problem is related to the Flash Voyager USB

• Satellite L650 - 12N USB Ports does not work

  My satellite L650-12N usb port does not work. I did everything that I could and it does not work.
  It shows a yellow exclamation mark on my system.

  I try so many ways, including the recovering auto troubleshooting, formatting and system he could not work.
  Under the key USB gives error code 43, I do not understand.

  The webcam and the wireless card no more.
  This boot problem after a storm in my area some time ago.

  Please can someone help.
  Thank you
  Sani

  Hello

  > This problem start after a storm in my area some time ago.

  Because other devices don't work properly and because procedure didn t get it back help you solve this problem, I think that the problem is related to the hardware malfunction possibly that the motherboard was hit by lightning, which would explain the problems

  I think you should ask the maintainer authorized Toshiba in your country to check the motherboard.

  But in my opinion, that the warranty does not cover the issues of environmental impact maybe your household insurance could help you

• USB ports do not work after waking up Satellite A200 from sleep mode

  After that I spend my Satellite A200-244 "sleep" or "hibernate" USB ports do not work!

  Hi mate,

  already tried this:

  Open start and type Device Manager and then press ENTER, to start Device Manager. Click on the sign + next to "Controllers of Bus USB" and then in the list, you should see some devices called 'USB hub root'. For each one, click right, hit properties, go to the power management tab and uncheck the box "Allow the computer to turn off this device to save power." Then restart.

  Maybe it works. Another solution would probably be this Microsoft KB document:

  http://support.Microsoft.com/?scid=kb%3ben-us%3B812946&x=8&y=9

  Greetings

• Satellite A10 s203: USB ports does not work

  Hello! All of a sudden my usb ports do not work on my satellite sa10-s203. Tried everything (even restarted the ashes of l-top nothing happened.) Enybody can help me? Kris...

  Hello

  If the USB ports are properly recognized in device then as Quad Manager said it could be an external problem. The USB port is 500mA power. If the external device requires more power to work in this case, it of necessary to use the external power supply.

  Good bye