Satellite P10 804: Toshiba Power Options - how to disable Hibernation

Similar Questions

• How to make a wireless upgrade on Satellite P10 804 card

  I have a satellite P10 804 and it has a 802. 11B wireless card built (only part no PA3171U-1MPC). It's too slow to stream multimedia from my office. My router has capacity G + and I would like to update my wireless card to be somewhere near the same speed. The upgragdeable of cards is integrated (easily)? If so, is the PA3374U-1MPC card compatible? and how can I change?
  Thank you
  Shaun

  Hello

  Yes, surely. You can improve it, but you should not use original toshiba parts. You can enter a Wi - Fi card with the standard of g on ebay for example and install it yourself. the wireless LAN card must be placed on the bottom of your machine behind a cover that is fixed with a screw.

  I suggest, if you plan to buy a new one, take an atheros card because they are affordable, they are stable cards and chipsets quality is very good (send/receive/you connecting to a network) If you can´t do something wrong with an atheros chipset.

  Welcome them

• Satellite P10 804: how to remove the HARD drive?

  I would like to remove the internal hard disk of 60 GB of my satellite P10 804 and replace it with a bigger drive, but cannot find a way to enter in the case of removing the HARD drive.

  Does anyone have the details on how to do?

  Hello

  To my knowledge, the HARD drive must be placed under the optical dirve.
  To remove the HARD drive, first remove the battery and the optical drive, and then follow the steps below:

  1. remove the four black screws that anchor the shield of aluminum covering the HARD drive and pull it out.
  2. gently pull on the HARD drive the front panel of the computer to disconnect the system board, then pull it out.
  3. remove the four silver screws that attach the HARD drive to the HARD disk case.

  But be careful. If you have no experience ask someone with more experience in these replacements.

• Satellite P10 804 will not accept the upgrade of RAM

  Apologies, this is it is a bit long and also if this question has been covered elsewhere here: I had a good nose autour and have not found something that seems to help.

  In any case, I had a Satellite P10 804 during these past years, I bought in the United Kingdom.

  Quite early in my time with this laptop, I upgraded the RAM. It was 3 or 4 years ago, when memory was not as cheap right now, so I bought just a single 1 GB module. P10-804 will take up to 2 GB of RAM.

  The P10 804 came with 512 GB as standard in two modules. My upgrade means I got 1.25 GB, which was in very good health. Everything was fine until the end of last year when the defective laptop; I followed the fault in module 1 GB of RAM. It was a bit awkward since I now live in New Zealand. However, the provider of the RAM was very professional, stood by their warranty, and we arranged a swap. RAM prices had fallen, so I bought another module of 1 GB at the same time upgrade the laptop completely.

  Now the problems really started. The laptop would not simply work with the new installed RAM modules. It would work with one alone, nor even less with my old configuration of a module of 1 GB and 256 GB module. Start and run for five minutes before a freeze; white screen with fans roar; blue screen; frozen screen normal with strange objects; No start at all. everything.

  Everything that works now is my original 256 MB module (his partner disappeared). This leads me to assume that I don't have some sort of hardware failure?

  1 GB modules are DDR333 SODIMM, CL2.5. This laptop will also have the DDR266 modules, and it has been suggested to me, lower speed might work. I can try this option since the RAM prices are * really * low now, especially if I get confirmation of this as a valid strategy possible.

  The laptop BIOS is updated to v2.00 (maybe?), and I also upgraded the HDD to a 120 GB unit (this works very well and is partitioned for XP and Linux). And from time to time I empty the fan.

  Any advice welcome. Thanks for reading.

  > The laptop would not simply work with the new installed RAM modules. It would work with one alone, nor even less with my old configuration of a module of 1 GB and 256 GB module. Start and run for five minutes before a freeze; white screen with fans roar; blue screen; frozen screen normal with strange artifacts; No start at all. everything.

  Reading your message, I came to the conclusion that this issue must be linked to the new RAM module and this module is malfunctioning or is not fully compatible with your laptop.

  The P10 can be upgraded to 2 GB, so you should be able to use two single RAM 1 GB modules

  So it must be a module problem

• Satellite P10 804 upgrading wireless card

  Hello

  Ive been trying to find a list of compatible wireless cards to upgrade my Satellite P10 804 but can't find.

  The wireless card is a Toshiba PA3171U-1MPC, but it does not have the standard 802.11 G and no WPA security.

  Anyone know of the good cards replacement that will work on my laptop?

  Ive met this one but I'm not sure if it's compatible or not because I can't find any compatibility for it info: PA3416U-1MPC

  Thank you

  Mark

  Hello

  I think that the PA3416U-1MPC should be compatible.
  I mean the laptop supports wireless Mini-PCI network card and PA3416U-1MPC is a Mini-PCI wireless network card.

  The WLan antenna behind the screen of the laptop computers must be connected to the connectors on the wireless Mini-PCI network card.
  Both connectors are identified with MAIN and auxiliary normally a white cable goes to the ESSENTIAL and a black at the entrance to THE

  Good bye

• Satellite P10 804: cannot use the day before and the FN keys / hibernation

  Satellite P10-804. I had a virus and this has been supported by a professional. Since I can't use my Fn key and therefore cannot standby / hibernate etc. The sleep function does not work also if I use the "standby" button mode start Microsoft.

  The system just trying to go to sleep and restarts again, sometimes doing, it resets the date and time of the computer. Any help would be greatly appreciated. Thank you.

  Hello

  May I ask why you n t use the recovery CD Toshiba to restore the operating system on the P10 Sat?
  Simply boot from the restore CD from Toshiba that came with the laptop. This CD contains the Windows operating system with all the drivers and tools pre-installed.

  The installation process takes about 10 minutes. It of very simple but please note that this new facility will format the HARD drive.

  Other questions?

• Satellite P10 804: where can I download the BIOS original version 1.1

  Is it possible that I can download the original bios version 1.10 for the P10-804 Satellite.

  Also the slash to the back button does not work. How can this be corrected?

  nevodoch

  Hello

  All BIOS for all Toshiba units, you can download from the Toshiba site:
  http://www.toshiba-tro.de/subpage/BIOS.html

  But you can not downgrade the BIOS for example: since version 1.2 to 1.1
  This is only possible by Toshiba ASP.
  In this case, if you want to downgrade the BIOS you should contact the service partner.

• Satellite P10-804 - Question on new install

  I am wanting to do a clean install on the old Satellite P10 [2004], but I'm a little worried about the updates that I'll have to do.
  In my view, that he could run in the hundreds.

  All Tips how do appreciated.

  Hello

  You can install the Windows operating system on your laptop and need to install the drivers of P10 separately
  The drivers can be downloaded from the Toshiba page.

  Of course, you need to update the Win for the last state operating system but it should run automatically, you can drink a coffee and wait ;)

• Order of error has been committed by satellite P500 - service TOSHIBA Power Saver

  Model:-PSPE8A-025002
  [http://www.mytoshiba.co.nz/products/home/notebooks/satellite/p500/pspe8a-025002]

  OS:-Windows7 Ultimate (32 bit)

  On start up to get a service stopped notification - "service TOSHIBA Power Saver was arrested, so cannot be changed".
  That is the only other cause the change of Windows 7 known behavior where the Eco Power Saver button is no longer works but the Control Panel/Power Options standard I can select and edit power plans as usual. So it is just an annoying pop up on start up.

  Tips to prevent the annoying notification welcome.

  BR /.
  Rob

  Hi Rob,

  Have you tried to reinstall Toshiba Value added Package? It contains current saver where you get this error message. You can download it here:
  http://EU.computers.Toshiba-Europe.com > support & downloads > download drivers

  I also recommend reinstall the Eco utility.

  Good luck! :)

• Satellite P10 804 is over heating and cutting

  My Satellite P10-0804 seems to be stopping down to often cause of overheating.

  I guess that there is a thermostat to control it.

  Is there away that I can fix this, without sending the unit?

  Changing the setting in the "Toshiba Power Management Utility" can improve things? With that, I don't see much possibility to change settings if the unit is plugged into current alternative.

  -In the "Advanced" tab, there is a selection for the "method Colling", default value 'Max Performance Mode' which is the best choice or can it be changed to 'Mid Performance Mode' or 'silent '?

  Hello

  No, you should not change some settings powersaver. Simply do the following:

  1. take a brush and a can with compressed air (which can be obtained in every electronics store)
  2. use the brush to clean the outer holes the cooling system for your processor
  3. use the bottle with compressed air to blow some air trough the cooling modules, I guess they must be really clobbed with dust
  4. If the product overheats again then go to a computer technician who is familiar with the mobile computing systems and let it clean the CPU cooling system correctly, including the fat CPU cooling

  That's all

  BR

• Satellite A110-178 - Toshiba Power Saver for Vista?

  Toshiba Power Saver doest exist for vista? I liked it when you work under XP, but now I switched to Vista Ultimate, and the version of XP does not work under Vist...
  Thanks in advance!

  Hello

  Toshiba has also developed and Power Saver for Vista and will be installed with added Vista package.
  But the energy saving of Toshiba for look of Vista doesn t as the saver of energy for Win XP.

  TOSHIBA Power Saver for Vista belongs to Vista power options, and you can find some additional entries in Vista Power Options.

  But you won't find a stand as only Toshiba Power Saver for Win XP.

  Good bye

• Satellite A100 PSAARE: Toshiba Power Saver + graphics card noise

  Hello

  Is there another URL where I can get a version update of Toshiba Power Saver for my computer drivers laptop Satellite A100 PSAARE other than the home page?

  It seems that it is not determinative of CPU fan (he always keep at maximum speed).

  Also, I noticed the graphics (GeForce 7600) too loud.

  If the monitor is off I can't hear it (just the CPU fan), but as soon as I started working it is audible and as a continuous beep kid.

  Is there a (software/hardware) fix for this?

  Kind regards.

  Hello

  The European driver of Toshiba page is one place where you can get the drivers and tools for your European Satellite A100 PSAARE model.
  This time it s a v7.03.07.I Power Saver for Windows Vista!

  But I must say that I see no problem of software on your laptop.
  Cooling modules and fans have to run with higher performance to make sure that your hardware components may be cooled properly.

  Maybe a cooling module cleaning might help to improve the internal cooling and noise reduction.
  From time to time, I clean my fans for laptop using compressed air stream and the fans are running more silent.

• Re: Satellite L300 - 17l - Toshiba Power Saver gives me error after installation

  When I bought my L300 - 17l all the drivers of Toshiba drivers download pafe worked out well.
  Recently, I have reinstalled my OS XP and now I started to install all the drivers again. LAN has been authorized, WLAN was ok, the display driver has been authorized.

  But when I get to install Toshiba Power Saver (URL: [http://support1.toshiba-tro.de/tedd-files2/0/pwrsav-en-20080519172104.zip]) it gives me this error (it shows the error or after I cliquerai on finish the instalation or before installation began, as you can see in this screenshot)-[http://www.picvalley.net/v.php?p=u/2381/9078672171740560287.JPG]

  I later tried this - i go ot Control Panel and open Toshiba Power Saver, but then it gives me another error: "CANNOT be opened because you do not have access rights to use 'TOSHIBA Power Saver'.
  I reinstalled my XP again and it still gives me this error... I wonder what could be the problem... Please help me

  Hello

  Satellite L300 - 17L belongs to the PSLBCE series.
  I chose this model number and found exactly the same energy saving that you tried to install.
  So I guess that you have chosen the right Power Saver utility for this model of laptop.

  But did you also install the common Module?
  This software must be installed first before installing other tools.
  Update you the Win XP for the State?

  Check it!

• Satellite A100 - message: Toshiba Power Saver already started

  When I turn on with power supply connected, I get a false error message that says 'Toshiba Power Saver already begun'.
  How can I get rid of this message permanently?

  Hello

  I guess that the Toshiba power saver trying to load twice.
  Akuma s suggestion should work.
  Once the energy saver has been uninstalled, all entries that control energy saver should be removed too.
  After this, reinstall the new energy saver

  The alternative might be disables a power saver in msconfig.
  To ensure that the access the msconfig (in RUN type msconfig) and remove the mark of an energy intake that you might find in the Startup tab.
  Then restart the laptop and check if it worked

• Problem reading DVD (SD-R6112) on the Satellite P10 804 under Xp Pro SP2

  My Toshiba DVD SD-R6112 (P10-804) now reads no DVD-r it just to burn with Nero 6.6
  The sysmtoms/anamnesis is therefore
  (1) it used to work fine. That is, that I never had a problem with playing on the P10 DVD, that I burned on the P10
  (2) DVDs burned before (before a few weeks ago) on the P10 continues to be readable on the P10
  (3) BUT DVD burned recently (5 or 10 last burned on 2 different types of media and two different burners) can be read in the drive of P10. The DVD is not yet recognized - it sometimes changes shape explorer DVD - RW CD - R, but that's all. No file, no nothing.
  (4) these same (unreadable by P10) DVD is very well played on two other DVD players I have (Freecom USB and divx standalone player). The drive can read the DVD (USB Freecom) CDFS file system reports, no free space (Nero 6.6.0.14 was said to not to allow future sessions) and all appear normal.

  The DVD driver is Microsoft 5.1.2535.0 1/7/2001. The DVD 1031 firmware revision.

  Nero was the only program running when the DVD is burned (no file to add). The verified OK after burning DVD.
  I can't find an update of the firmware on the Toshiba site so I'm a little stuck on what to do next
  Any ideas?
  TFAI

  Hello

  I read in several journals, computer and on some sites that not all drives are compatible with all media. Sometimes, readers cannot read the media burned because of the 3rd party software that prevents access to the media or files.
  Generally, it is not easy to say why some readers read and write media and some readers cannot handle the same media. There are many factors.

  Sometimes, the firmware update will help you resolve problems with reading or writing.
  I found this SD-R6112 page with a driver for this device and the latest firmware version.
  http://www.Toshiba-Europe.com/storage/PDL.asp?page=PFW&NAV=RSC_PDL&model=SDR6112&PTYPE=D VDRECSL