Satellite P100-240: Media Center Edition - error 3

I recently installed the Toshiba TV DVB, set up all channels and guides, then recorded a number of television programs.
Unfortunately, when I have pulled up my Satellite P100-240 this morning to check the last recordings of nights, the Media Center told me that I had deleted all of my recordings.

I tried to get the library going again without success.
All I get is a window telling me that there may be essential audio and video files missing and he said that I should quote "error 3" when looking for support. ".
I tried reinstalling the drivers, etc., but it just goes back to "error 3' anyone able to help?"

It is a very strange question. To be honest I really don t know what happened with you Windows Media Center software.
It s a program from Microsoft and my personal experience, sometimes inexplicable things

What you could do is trying to roll back the BONE to this early time!
Eventually a point system restore has been created and you can set the operating system on this point.

I also recommend to check your recorded programs.
Usually programs stored is located in the following folder:
C:\Documents and Settings\ all TempSBE TV
Maybe you could save these files.

Tags: Toshiba

Similar Questions

  • Qosmio G20 - Microsoft Media Center Edition - ehExtHost.exe error

    I started having errors on my Qosmio G20 ehExtHost.exe when pass the screen of Media Center edition to record a television show.

    Language Runtime Debugging current Service ID = 0x17d4 (6100) and id = 0 x 138 (312)

    I have a glance on the web and found a few comments about Norton screwing of the NETWORK settings, I've just updated Norton Internet Security 2009 version so it's possible.

    I have also a message with something not being able to connect to Windows Messenger so don't know why it would.

    I recorded a program and it's OK when I played it back.

    Anyone has any ideas how to solve this problem (or problems)?

    MB

    Googling around you can find so many reports about this. I also found an interesting article on this subject. Please check it out. Maybe it will help you to solve this problem.

    How to solve the ehExtHost accidents that may occur during the launch of Media Center?

  • Satellite A100: Need drivers for Windows XP Media Center Edition

    Hi there, hoping someone can help me, just bought Windows XP Media Center Edition, had home installed, installed a new and I'm missing some drivers (Ethernet controller, mass storage controller, network controller, PCI device and video controller VGA)

    I have a satellite A100 PSAA9E and I was wondering if there is no driver for this edition of windows yet or if there is no alternative that is pro XP drivers should work?

    Thank you
    Andy.

    Hello

    On this page of Toshiba, you will find drivers for different units.
    http://EU.computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/download_drivers_bios.jsp?service=EU

    Win MCE drivers are not available for Satellite A100, only Win XP.
    Jasmin said, you can try to use the Windows XP drivers as the Win MCE is a WinXP with additional features.
    Check it out

  • I have Windows XP Media Center Edition Version 2002 with Service Pack 3 and I tried to run Media Center but I get an error message with ehshell.exe.

    original title: error with ehshell.exe

    I have Windows XP Media Center Edition Version 2002 with Service Pack 3 and I tried to run Media Center but I get an error message with ehshell.exe. Could you help me?

    This problem exists since the 1st Media Center. SP2 and SP3 had a difficulty, but it is obvious that it doesn't always. The same problem still exists in Vista today with a lot of other carried over from XP. System restore would work, but you do not have any good restore points so reinstall an operating system seems to be your only option.

    You probably don't want to do an OS reinstall you need for Media Center, but since it does not at all, you might want to play then remove the Media Center updates and or SP3 and reinstall them.

  • Windows XP Media Center Edition - get code 0x8024400A error when you go to the Windows Update site

    I had to reinstall my OS, XP Media Center edition 2002 with Service Pack 2, and when I go to the Windows Update site I get the following message "0x8024400A - site error Code has encountered a problem and cannot display the page you are trying to view. The options provided below may help you solve the problem. »

    Can someone tell me what may be the problem?

    0x8024400a

    -2145107958

    SUS_E_PT_SOAPCLIENT_PARSE

    http://support.Microsoft.com/kb/836941

    UTC/GMT is 09:05 Sunday, June 10, 2012

  • Ehshell.exe error with Windows XP Media Center Edition Version 2002, service pack 3

    Running Windows XP Media Center Edition Version 2002 with service pack 3.  I get the ehshell.exe error when I try to watch live TV.  It crashes, debug and I usually won't have to ctrl-alt-del to get anywhere.  Do not seem to have this problem before I added various updates etc, tv was fine before this date.

    I'm not particularly computer so nice easy steps please...!

    Thank you, Nicholas

    Ehshell.exe is a Windows system file that is used to run Microsoft Media Center. It is not a critical system file. However, the ehshell.exe file can become infected and cause errors trying to run certain programs. If the ehshell.exe is absent, it can also cause errors. Reinstall a clean copy of ehshell.exe with the Microsoft System Restore.

      • 1

        Click on the "Start" menu, then click on "programs". Scroll down and click on "Accessories," then "system tools." Click "system restore."

      • 2

        Click 'Next' in the window system restore for a list of points of restoration which has been archived.

      • 3

        Select a restore point created before the ehshell.exe file becomes corrupt or got deleted. If no restore point until this time is listed, click on "Show restore points more" to select the one that is before this date. Click 'Next' to choose which restore point.

      • 4

        Click 'Finish' to start the system restore. The computer will restart once the process is complete and the ehshell.exe file is reinstalled.

  • I have Windosx XP Media Center Edition 2002 SP2, whenever I try to install sp3, that an error and I need to go to a previous configuration, what do I do to be able to install sp3?

    I have Windows XP Media Center Edition 2002 SP2, whenever I try to install sp3, that an error and I need to go to a previous configuration, what do I do to be able to install sp3?

    I have enough information about your computer to give you assistance-oriented. This might help:

    How to troubleshoot an installation fails to WinXP SP3 - http://support.microsoft.com/kb/950718 MS - MVP - Elephant Boy computers - don't panic!

  • Satellite P100-240 includes the numeric keypad, and HD Audio and HD video

    Hello

    I will soon buy a Toshiba Satellite P100-240 of LaptopsDirect with a memory upgrade. It says on the site Web of Toshiba, the P100 is not HD Audio and HD video and it also States that it does not include the numeric keypad. Is - this ture? The processor is good on this machine, I mean like a Core 2 Duo.

    It also comes with Microsoft Windows XP Media Center Edition 2005, is it possible for me to get a buyout of Toshiba site upgrade

    I highly appreciate your replys
    Thank you
    Machanic

    Hello

    > Is the processor good on this machine, I mean like a Core 2 Duo

    The CPU is not better than Core 2 Due because he s successor to core Duo.
    Intel Core Duo processor T2400 1.83 GHz Yonah works on this laptop.
    You can check the detailed specifications of this CPU Intel page.

    In addition the unit supports audio chip type high-definition Intel Conexant CX20551-22.
    I put t know what you mean by HD video.
    Do you mean the HD player? The portable player is a simple DVD Super Multi drive (+/-R Double Layer) and it does not play any DVD HD

    You can also check this Toshiba page for more details:
    http://UK.computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/JSP/productPage.do?service=UK&PRODUCT_ID=119355&Toshib aShop = true

  • Satellite P100-240 power management issues

    Hello

    Since then, a few months ago, on my P100-240 power management was terrible. The problems are...

    1 if the monitor turns off through inactivity, the only way back switch on is to close and open the display (or trigger the sensor screen closed with a pencil).

    2 the machine is born in the life of hibernation if you close the screen. The only way to enter Hibernate with screen closed is to close the screen while the machine is in hibernation.

    3 Hibernate with the display closed, the machine springs to life if moved or slightly shaken. Accordingly, it is dangerous to transport it without performing a full closed.

    Are all my problems with a sensor defective screen closed, or are other people tolerate the same garbage?

    I've updated to the latest version of the BIOS. I am running win XP Pro SP2. To try to limit this behavior, I chose "when I close the lid of my laptop--> status quo' in--> Advanced Power Options. This made no difference.

    Thanks in advance.
    What about Simon

    Hello

    First of all I m very interesting if you use the Toshiba preinstalled the operating system?
    You said, you use the Win XP Pro OS and as far as I know the laptop was supplied with the Windows XP Media Center Edition 2005.
    It s really interesting if this behavior of the laptop appears with the image of Toshiba preinstalled.

    In any case, because of the third point (hibernation with the display closed, the machine comes to life if moved or shaken slightly) I guess there could be something wrong with the sensor screen-closed for laptop or with contacts on the motherboard. But to be 100% sure the diagnostic test is necessary!

    Looks like you guarantee is valid! Contact the ASP in your country and explain the guy the whole situation!
    All tests and replacements should be done for free! So don t worry dude!

    Good luck

  • Satellite P100-240 only works with ACPI disabled

    Hello

    I recently bought a second hand P100-240.
    For a day, it worked very well, and I tested it with sisoft sandra, 3dmark, many games etc.
    All played well, and it was not overheating and really powerful.

    Then a day later, he just got started while I was using it. On reboot, it will reach point just sign into windows XP Media Center edition and then cut. Even in safe mode, exaclty the same thing would happen.
    I left it for a few hours, in which case it was overheated, but the same thing happened when I retested.

    I tried the live cd Knoppix, and initially it would turn off at halfway by starting.
    Then I tried to run the Knoppix with a "acpi = off" option and it starts very well!.

    Also, I have tried many BACK start-up based utils and these well everything worked.
    I tested the disk, the cpu (stress and burn in tests), memory (memtest). All tools ran fine and all tested ok (and the machine does not idle)

    I tried to install a copy of windows XP alongside XP MCE, but that on the installation screen lists the existing partitions, and the machine would just power off.

    So try the Knoppix ACPI thing, I tried to install Windows XP without ACPI (i.e. a STANDARD pc), and he got through the fine installation. Now, I have a fully functional laptop again and can play all the games etc like before. Everything I have disappeared are ACPI some associates of power options.

    Now, what I want to know, is this ACPI issue a collateral or the related issue of the BIOS?

    Im running 4.40 BIOS, which is the latest BIOS for the p100-240 (PSPA3E).

    Is there a previous BIOS, which is perhaps more stable and will work around this ACPI problem? But the confusion is how all it worked well for a day and a half at the start?

    Any thoughts would be helpful.

    Hello

    In my opinion, the laptop is closed due to a higher internal temperature!
    The point is that the laptop supports protection against overheating and sensors (ACPI Advanced Configuration and Power Management Interface) who would yell at the bottom of the unit automatically to prevent damage.

    You said that this happens all by playing a few games. This heavy application leads to higher heat dissipation and therefore the temperature rises.
    I think that you should first check your cooling modules if they are not clogged with dust and debris. A compressed air jet pourrait helps get rid of the dust.

    Second, you must use the graphics drivers from Toshiba because such driver was designed for the use of the laptop and controls the heat dissipation the GPU too.

  • Windows not start successfully after updating BIOS on Satellite P100-240

    Hi all
    After you install a new version of BIOS my laptop wouldn't start windows xp properly.
    It just freezes in a screen black, I was able to go in safe mode, but then I reinstalled windows and now it's the same problem and I can't go in safe mode as I haven´t went through all the procedures of installation of windows.
    Please help me: I can reset the BIOS to my old?

    I use a satellite P100 - 240 (PSPA3E) and any help would be greatly appreciated.
    Thank you

    Hello

    What version of BIOS you have loaded? Version 4.20?

    Normally it shouldn´t do problems, especially after upgrading your BIOS. May I ask if the version of Windows installed on your machine you´d is on the media recovery or from scratch (from scratch means install with a genuine Windows CD and install the downloaded drivers)?

    If everything fails then send you the machine and let check the laptop on certain shortcomings of the BIOS.
    Click [HERE: http://eu.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/download_whitepaper.jsp?service=EU&WHITEPAPER_ID=0 000000871] to reach the index of ASP (authorized service provider) and find one that is closest to your country.

  • Problem installing Windows XP Pro/Windows Media Center Edition

    A few years ago, I built a system which consists of MS Windows Media Center Edition.  Recently, the hard drive failed.  I replaced the drive with a 1 TB Seagate Barracuda SATA drive.  Strangely, I can't reinstall MS Windows Media Center.  To clarify... with MS Windows Media Center cd in the drive, the installation went well.  The hard drive has been formatted and that the CD-ROM files have been hard disk messages were present.  The next step was a reboot by MS Windows cd.  This is where the installation fails. After the reboot, the Windows XP splash screen came as if the program Windows opened on your desktop.  At halfway through the splash screen, the system restarts.  Reboot forever more.  I don't know what is happening. Anyone?

    Test your player - create a Bootable CD:
    Ranging from 5 to 25% (depending on the make and model) new hard disks are defective.

    If you have a new hard drive Seagate the very next thing would be to download Seagate Seatools
    (bootable CD) and check bad sectors.
    SeaTools for information: http://www.seagate.com/support/downloads/seatools/
    SeaTools for Windows download: http://www.seagate.com/support/internal-hard-drives/enterprise-hard-drives/saturn/seatools-win-master/
    SeaTools for DOS download:
    http://www.Seagate.com/support/internal-hard-drives/consumer-electronics/LD25-series/SeaTools-DOS-master/

    HD Tune:
    Provides information of the car and has an option (tab scan error) to test your drive.
    http://www.hdtune.com/

    SpeedFan:
    Monitors internal temperatures and has a function of analysis health online (SMART tab) for hard disks drive.
    It displays your drives model number and compares your drive with other discs of the same brand and model.
    http://www.almico.com/SpeedFan.php

    J W Stuart: http://www.pagestart.com

  • Xbox 360 and Windows XP Media Center Edition 2005

    Hello

    Hoping to get help with this, because I searched everywhere and had not found an answer.  All the work around the items, reference Windows 7 and 8 not XP my Dell Dimension C521 shipped with Windows XP Media Center Edition 2005 pre installed.  I've upgraded to SP3 of XP.  A friend of mine gave me his old Xbox 360 (bought a new unit).  When I try to connect to the XBox 360 I get an error message in media library "uninstall the update for media center 2005 and then re-install the update of the site Web of Windows update.  Then, re-run Setup for Xbox 360'

    I checked in my under settinds program control panel, but don't see any element for Media Center 2005, even with show checked all of the updates.  I don't see Media player listed and 2 updates for it.  I have disabled the Windows Firewall did not help.  The Xbox 360 test shows that I can connect to the internet, Xbox Live (no NAT problems) and PC running Media Center.  It fails on the media center connection test.

    I don't want to reinstall all of the Dell backup image software supplied with the camera, I'll have to back up and start over.  Any help is welcome!

    Thank you

    Matt

    Hello

    Thanks for posting your question on the Forums of community of Microsoft.
     
    I suggest for the link and follow the steps in the article:
     
    Error message when you try to install a program for the Xbox 360 Media Center Extender in Windows XP Media Center Edition 2005 with Service Pack 3: "There is a problem with the installation of Windows XP Media Center Edition 2005"
    Important this section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:
    322756 (http://support.microsoft.com/kb/322756/ )
    How to back up and restore the registry in Windows.
     
    Also see Help links:
    Turn your Xbox into Windows Media Center Extender
     
     
    Windows Media Center on the Xbox 360
     
    I hope this helps.
  • Problem, reinstall the Update Rollup 2 for Windows XP Media Center Edition 2005

    I have problems with MCE 2005.  My hard drive crashed and the technician that restored my repressive said that he could not work in MCE 2005.  It's a shame because he was working before the hard drive crashes.  I work with windows XP.
    When I go to install the internet and begin to test the connection it gives me "Critical error of process - Code 2"
    When I go to the TV configuration, it tells me "Tuner not found".  Even if I know it works because I also Win TV7 in Hauppauge. My TV tuner is HVR-1600.
    With these problems, I thought that the solution might be to reinstall rollup 2 according to the Microsoft.
    http://support.Microsoft.com/kb/910905
    However, when I go to reinstall the Update Rollup 2, it seems to be to establish a restore point and then it stops when it hits hotfix (KB891593).
    I took a copy of the mcelog and have attached a copy of the log below.

    Assistance or management, you can provide me to solve this problem would be highly appreciated.

    At this point, I'm a newbie to this and I don't have a clue as to the cause of my problems and any ideas you may have for me would be much appreciated.

    A generic Package: 10/28/10. 21:32:48
    Looking for an existing installation of the generic package

    A generic Package: 10/28/10. 21:32:48
    Looking for an existing installation of the generic package
    Process creation: WindowsMedia10-KB895572 - x 86 .exe/quiet /norestart
    Process returned 0 x 00000000

    Function (ExecCmdInThread) Message of Post for the Package id: 1045.

    A generic Package: 10/28/10. 21:33:02
    Looking for an existing installation of the generic package
    Process creation: WindowsXP-KB891593 - x 86 .exe/quiet /norestart
    Process returned 0 x 00000000

    Function (ExecCmdInThread) Message of Post for the Package id: 1046.

    A generic Package: 10/28/10. 21:33:02
    Looking for an existing installation of the generic package

    Process creation: WindowsXP-KB895961 - x 86 .exe/quiet /norestart
    Process returned 0 x 00000000

    Function (ExecCmdInThread) Message of Post for the Package id: 1047.

    A generic Package: 10/28/10. 21:33:02
    Looking for an existing installation of the generic package
    Process creation: WindowsXP-KB899337-v2 - x 86 .exe/quiet /norestart
    Process returned 0 x 00000000

    Function (ExecCmdInThread) Message of Post for the Package id: 1043.

    A generic Package: 10/28/10. 21:33:02
    Looking for an existing installation of the generic package
    Process creation: WindowsXP-KB899510 - x 86 .exe/quiet /norestart
    Process returned 0 x 00000000

    Function (ExecCmdInThread) Message of Post for the Package id: 1043.

    A generic Package: 10/28/10. 21:33:02
    Looking for an existing installation of the generic package
    Process creation: WindowsXP-KB888795 - x 86 .exe/quiet /norestart
    Process returned 0 x 00000000

    Function (ExecCmdInThread) Message of Post for the Package id: 1043.

    A generic Package: 10/28/10. 21:33:02
    Looking for an existing installation of the generic package
    Process creation: WindowsXP-KB902841 - x 86 .exe/quiet /norestart
    Process returned 0 x 00000000

    Function (ExecCmdInThread) Message of Post for the Package id: 1043.

    A generic Package: 10/28/10. 21:33:02
    Looking for an existing installation of the generic package
    Creation process: KB900325.exe/quiet /norestart
    0x00000bc2 returned by process

    Function (ExecCmdInThread) Message of Post for the Package id: 1048.

    "Creative process: c:\0f7019deb34a2ccd3d5c2a4d9e4f3e57\bin\wmfdist95.exe/q: a/r: n /C:"wmsetsdk.exe/WMFDIST/q/r: n /DisallowSystemRestore.
    Process returned 0 x 00000000

    Function (ExecCmdInThread) Message of Post for the Package id: 1044.

    A generic Package: 05/12/11. 21:26:14
    Looking for an existing installation of the generic package

    A generic Package: 05/12/11. 21:26:53
    Looking for an existing installation of the generic package
    Process creation: WindowsMedia10-KB895572 - x 86 .exe/quiet /norestart
    Process returned 0 x 00000643

    Function (ExecCmdInThread) Message of Post for the Package id: 1045.

    A generic Package: 06/03/12. 21:27:50
    Looking for an existing installation of the generic package

    A generic Package: 06/03/12. 21:28:23
    Looking for an existing installation of the generic package
    Process creation: WindowsMedia10-KB895572 - x 86 .exe/quiet /norestart
    Process returned 0 x 00000643

    Function (ExecCmdInThread) Message of Post for the Package id: 1045.

    A generic Package: 12/02/13. 09:44:39
    Looking for an existing installation of the generic package

    A generic Package: 12/02/13. 09:45:16
    Looking for an existing installation of the generic package
    Process creation: WindowsMedia10-KB895572 - x 86 .exe/quiet /norestart
    Process returned 0 x 00000643

    Function (ExecCmdInThread) Message of Post for the Package id: 1045.

    A generic Package: 12/02/13. 10:11:58
    Looking for an existing installation of the generic package

    A generic Package: 12/02/13. 10:12:30
    Looking for an existing installation of the generic package
    Process creation: WindowsMedia10-KB895572 - x 86 .exe/quiet /norestart
    Process returned 0 x 00000643

    Function (ExecCmdInThread) Message of Post for the Package id: 1045.

    Hi kwanray,

    Welcome to the Microsoft community. According to the description of the problem, you can not reinstall the Update Rollup 2 for Windows XP Media Center Edition 2005.

    I'll help you with this problem. I suggest you follow the steps in the article.

    Update Rollup 2 for Windows XP Media Center Edition 2005

    Reference: Support for Windows XP Media Center Edition 2005

    Let us know if you need help with Windows related issues. We will be happy to help you.

  • Update of XP Media Center edition after system restore

    I had to do a restore of the system on my XP Media center edition computer.  I now try to update the program installed at the factory.  It won't let me update.  Any suggestions?

    I had to do a restore of the system on my XP Media center edition computer.  I now try to update the program installed at the factory.  It won't let me update.  Any suggestions?

    You mean the Windows updates?

    Refer to this post:

    http://answers.Microsoft.com/en-us/Windows/Forum/windows_xp-windows_update/how-can-i-get-Windows-Update-error-x8024400a/35ba7694-c9b2-4043-a4c0-777d4b7736dc

Maybe you are looking for

  • When Firefox startup options, ' show my windows and tabs "is grayed out?

    Tools, options, general - startup of firefox I would choose "show my windows and tabs from last time", but it is grayed out?

  • Strange question after upgrading RAM on Tecra M10

    Greetings gurus, Pleeeaase help... I recently upgraded my M10-PTMB1E to 8 GB of RAM of 2 GB. My bios sees 8GB, Windows tells me I have 8 GB installed but 3.8 GB usable, it checked with a boot CD. Then, I pulled one of the external 4 GB chips and repl

  • 8GB in X200s?

    There will be new modules SODIMM DDR3 such as Kingston KVR1066D3S7/4 G. They will be usable? Rolf

  • single-precision changes constant value

    See attached 'vi '. If I set a digital double precision on my schematic, change it to SINGLE-precision, then enter the valeur.001 inside, he adds values to the right of the decimal point. Why would he do that? I'm using Labview 2011 SP1.

  • tabs move

    I can only open new tab and use it. Because the tabs do not switch. Change of address in an address field, but nothing more happens.