Satellite P100-286 with no display after installing drivers

I reinstalled XP on my 286 P100, as I did a couple of times before and went about installing the XP drivers on the Toshiba site. I was installing video drivers when the screen went black. I assumed it was a regular part of the installation of the video driver, usually the screen goes black for a few seconds, but the screen remained black.

I tried various commands on keyboard, but nothing has worked. So I restarted the laptop. Now, the display lights at all. I can't even an external monitor to show anything.

Any advice would be appreciated.

Hey,.

Can you see photo when you in BIOS mode for example?

If so, you should try to go into safe mode and remove the display driver. Maybe something was wrong due to the installation of the driver

Tags: Toshiba

Similar Questions

  • Satellite P100-286: cannot use Bluetooth after installing XP

    I have a portable P100-286 Satellite with bluetooth. It used to work OK but since I re-installed Windows XP SP2 I can't use bluetooth.
    There is nothing in the control panel and nothing in the hardware Manager that mentions the bluetooth.

    I installed al the latest drivers and BIOS updates and still nothing.

    Does anyone have any ideas why I don't see bluetooth?

    I think that you didn't install the driver BT properly and didn t activate BT

    First download the pile of BT since this Toshiba BT Portal:
    http://APS2.toshiba-tro.de/Bluetooth/

    BT installation restart the laptop and turn it on by using the FN + F8 key combination!

    Hope that this will enable BT again

  • Satellite P100-286 - video RAM shared with RAM system

    Hello

    First note that I m French sorry for the bad English, I can use.

    I have a satellite P100-286 - PSPAGE (T7200 @ 2 GHz, 2 GB DDR2, Gef7900GS) and I noticed that some of the RAM (exactly 271MB) was reserved for the graphics card.

    I think that the graphics card has enough memory with its 512 MB, so I don't want to have a part of my RAM to be reserved for the Geforce. I have not found the way to reassign this small part of the system in the bios, and it is independent of the OS (I use Vista and debian and I see the booking even on memtest86) so I ve tried to flash with the latest BIOS but no change.

    Is there a way to 'recover' my memory?

    Thank you

    Additional question for fans of Linux: why can not I get sound on my laptop running Linux? :'(
    It seems that there is no error, but there is no sound even if the sound card, the "HDA Intel", seems to work perfectly, even with the latest updates of the kernel and alsa.
    I tried several Linux distributions, including Suse and Mandriva.

    Hello
    Unfortunately you can not affect the amount of memory shared by yourself since it is regulated by the BIOS/Chipset and depends on the amount of main memory that is installed.

    As far as I know that the shared memory is allocated flexible, which means that if a graphical application needs a graphics memory more then the system returns to the 271 MB shared memory. That's what I know of my machine... but I don't know, it might be different on other models.

    Otherwise I have no information on this shared memory thing. You can also see this article: http://en.wikipedia.org/wiki/Shared_Memory_Architecture

    See you soon

  • Satellite P100-160 with Vista: No TV-OUT after downgrade to XP

    Hi guys hope you can help me out here...

    I recently bought a laptop (satellite p100-160) with Vista on it to know that it was not compatible with wot I bought dethrone so I decided to downgarde for XP Home Edition... Solange decommissioning that I had to install a few drivers like there's do and everything went well...

    Anyway, a few weeks later (yesterday), I went to watch a movie and when I pluged in my tv out cable, I have nothing. I tried to unplug and plug in again a few times but still nothing, it normally switches on in about 20 seconds... So im guessing that either I need to a driver or a Summit.

    Can someone help me out here?

    Thanks a lot

    You n t need a special driver to use the s-video port.
    You must install only the compatible graphics driver.

    How have you tried to switch to the TV device?
    Have you used the FN + F5 key combination?
    You should do this.

    Connect the TV to the laptop using the s-video port. Then select the s-video on the TV and choose the right channel.
    Press the FN + F5 several times until you get a picture on the TV.

    Please note; Don t start the DVD software like DVD win until you have not enabled on TV!

  • Satellite P100-286 - vertical on the screen restart and constant lines

    I got this P100-286 with Nvidia Geforce Go 7900 GS and recently the laptop started to freeze options even with vertical lines on the screen tried recovery cd tried to re - install and after installation, that he started to do the same. I have read similar problems in the forum and this is a common problem with Toshiba? I have spend £1500 on this and it is only 3 years old. My friends have older laptops of this almost 6 years old and in good working condition.
    Y at - it a suggestion for this problem or a solution? The heat on the basis of the laptop is really hot and it's like that for centuries.

    Any help is really appreciated after spending so much like to last longer or it is a problem of reliability with the Toshiba brand.

    Hi vns.

    Hmm strange. I have ever read on these issues here in the forum with Satellite P100. Friend of me has the same model and it s still does work correctly, no problems at all.

    Do you have the same vertical lines on a screen? If so, it is certainly associated with the internal graphics card and not watch.
    By the way: you have the same problem in the BIOS or just Windows?

    With regard to the heat on the underside: I think that it s time to clean it and remove dust. You can do this using the jet of compressed air to blow the dust from the cooling fans. That's why it of not necessary to disassemble your laptop.

  • Satellite P100-286: Explorer no longer responds when leaving hybernation

    I have re-installed Vista from disk Toshiba supplied with the cleaning machine, gone through the process of updating, that is microsoft and Toshiba updates and drivers.

    I have searched data base Microsoft on the errors of Hybernation for Vista, most are to do with the USB, but without coming through what im getting.

    My problem is that if you come from hybernation explore stops responding and does not recover.
    I have tried to restart Explorer by the Task Manager but still don't get the desktop or allow me to stop in the correct Manor.

    Regarding loans Vista boot USB that I use, which stuck ok to use it in vista, activate or disable the always the same problem.

    Do you have ideas about how this can be fixed.

    Based Satellite P100-286, but with 4gig of RAM

    I presume, after reboot, you can use new IE. Am I right about that?

  • "Plugged in, not charging" Satellite P100-286

    Hey people, well I've been having this problem just now, I have a Satellite P100-286, OS: Windows Vista Home Premium and my problem is that after I m using my laptop for a little while on the current if I am it loads, it will stop charging and if I hover over the battery icon n the taskbar It will say "Plugged In no current charging" and the battery life will not be 100%.

    I also note that in this case, the light of battery on my laptop is not blue indicating the battery is full (of course), but neither is it orange indicating that he is in charge, but a few times I noticed that the light flashes when this happens not all the time. I played games with the power adapter plugged in and sometimes the laptop is off and when I turn it back on and "resume windows" warning message will appear saying 1% etc.

    Please someone help and give me some advice on why my battery doesn't charge sometimes, I searched on the net about it and it is not the charger or the battery itself, but it's a hardware problem, people say, please someone kind and cleaver out there help me please.

    I KNOW there are a LOT to READ IM SORRY... hehe... BUT PLEASE HELP: p

    > Please someone help and give me some advice on why my battery doesn't charge sometimes, I searched on the net about it and it is not the charger or the battery itself, but it's a hardware problem, people say, please someone kind and cleaver out there help me please.

    You should know that it is not easy to provide an exactly fault diagnosis without putting his hands on her.
    What we can do is to provide some sort of suggestions

    So I think it could be a faulty battery, so first the battery should be checked.
    If problems still persist, then electronic power supply failure might be possible

    However, the equipment should be checked and this can be done by an ASP in your country
    It would be desirable to communicate with these guys and ask for help

    Good bye

  • Satellite P100-286 - charge not completely even in stop...

    Hey all,.

    I have a Toshiba Satellite P100-286 and my problem is that when it s on and I plugged it load the light orange will be on indicating that the load and it will say connected load, but the battery life does not exceed 96%, yesterday he wouldn t go above 97%, and once again on the eve of 98% (lol) , the thing is when I have the laptop off and have supported (the witness orange still on indicate its charging) it will not load fully. When I turn on my laptop it is always 1% less than it was the last time I got it on as you can see by whats described above... I'm sorry for the long post, it of just quite difficult to explain.

    So can someone please help? Is it my battery what should replace is exhausting? Or is it something to do with the BIOS?
    Please help, thank you in advance for any response.

    Hello

    When the laptop is ON try to remove the battery and after a minute or two inside put once again. Please let me know what happens after that.
    To be honest, it is not easy to say why this happens exactly. I don't think THAT BIOS is responsible for this.

    Have you used the battery power intensively or your laptop worked mainly on feeding current?

  • Satellite P100-286: cannot change "Customization" options in the Panel

    Toshiba Satellite P100-286

    Hello guys!

    Can someone help to solve my problem? For some time, I am not able to change/enter in ma, for example: screensaver of personalization in Control Panel. I can use only 2 of 7 available in "Customization" options/links Could someone help me, please?

    "Customization" isn't the only one of all the icons I can't come. There is a bit more such as: keyboard, Mail, regional and Language Options etc. Looks like the links to each of them does not work for me! :(

    I don't want to go through reinstalling Windows Vista so any help to solve this problem will be greatly appreciated!

    Thank you very much!

    Krzysztof (Chris)

    PS. one last thing, I tried to restore my system to the previous point, but I'm not able to do.

    Hello

    It is very strange to believe me, it's not easy to say why it happened and, therefore, we must study a little bit
    Did you install third-party applications on your laptop that could have a negative influence on the operating system?
    Have you changed the rights of account user or something like that?
    How about Antivirus applications? Always update you this software? Maybe it s a kind of virus

  • Can I use 2.1 speakers on my Satellite P100-286

    Can I use some 2.1 speakers on my computer toshiba laptop?

    supported audio formats: 16 bit stereo
    supported audio standards: MIDI support
    speakers: Harman Kardon stereo speakers
    Manufacturer: Toshiba Bass Enhanced Sound System with SRS TruSurround XT technology

    I don't see any reason why you shouldn't be able to use the 2.1 speakers on your Satellite P100-286.

  • How to get 5.1 sound on Satellite P100-286

    I had to replace my old P100-347 of 2 months, because of cracks on the hinge. The only model they had available was the P100-286. It is almost identical, except one thing, that I was not informed until I got it home and so too late to resume.

    Basically, the P100-347 had a SPDIF port and the 286 (as far as I can see), does not work. So, what I want to know is, what kind of sound that I am able to get the decision-making helmet.

    I plugged my Dolby Digital amp, and everything seems to be able to get is 2 audio channels, when I would be able to get 5.1 channels... In fact, I would like to have SPDIF, but don't think it will happen.

    Can someone advise and give me some advice on solving this.

    Thanks in advance
    Steve

    On the Satellite P100-286 S/PDIF port is not available and if you want to have 5.1 surround sound you need to use an external solution connected to the USB port. Google around. You will find quite different products, that you can use with your laptop.

  • did someone had problems with lightroom 5 after installing Mac OS El Capitan?

    did someone had problems with lightroom 5 after installing Mac OS El Capitan? the images are well n the library but darken when I switch to develop fashion

    It's a shame that you did not check for problems before you can update your Mac

    First, see if the update to the fixed bug Mac 10.11.1 will help you

    -an exchange of views of 10.11.1 https://forums.adobe.com/thread/1986008

    -In ADDITION the need to update the drivers nVidia (links included in the message)

    -There is also 'a' mention of an another 10.11.2 bug fix tested by Apple

    He has problems with Mac 10.11 El Capitan... which is perhaps one of them

    See answer #5 in https://forums.adobe.com/thread/1965850 for several solution links

    -the first link that the answer is a possible solution to install problems

    -There is also a link on the video display problems in Premiere Pro

    - and many other programs... MORE Microsoft Office also has problems

    More official Adobe help pages listing problems Mac 10.11

    https://helpx.Adobe.com/Photoshop/KB/Photoshop-and-El-Capitan-Mac-OS-10-11.html

    http://blogs.Adobe.com/PremierePro/2015/10/Premiere-Pro-CC-and-Mac-OS-x-10-11-El-Capitan.h tml

    https://helpx.Adobe.com/Lightroom/KB/Lightroom-and-El-Capitan---Mac-OS-10-11.html

    http://blogs.Adobe.com/audition/2015/10/audition-CC-and-OSX-10-11-El-Capitan.html#.VjjYBtG raUk

  • Upgrading RAM on Satellite P100-286

    Hello, I'm looking to upgrade the RAM on my laptop Toshiba Satellite P100-286. I did some research but have resulted in conflicting reports.
    RAM DDR2 RAM right or is it So DIMM DDR2 RAM? According to the Toshiba site, it is not, but when I go to one of the sites Web "Upgrade your Ram" and enter my brand and model, he suggested the So-Dimm type...

    I'm looking for a little clarification. Thank you.

    http://UK.computers.Toshiba-Europe.com/innovation/JSP/SUPPORTSECTION/discontinuedProductPage.do?service=UK&DISC_MODEL=0 & ACTION = PRINT_WITH_BACK & com .broadvision decided .do w = Yes & PRODUCT_ID = 125204

    See this page:
    http://www.orcalogic.co.UK/ASP/ProdType.asp?ProdType=28328&ft=m&St=3

    You will find details on the compatible RAM modules:
    You need DDR2 533 MHz (PC2-4200) 200 - PIN SODIMM

    Of course, you could choose another manufacturer like Kingston but I m using Kingston modules in my other laptop and it s ok.

  • Problems after installing drivers for HP Photosmart 5510e

    I was helping my sister set up his new printer HP Photosmart 5510e on a laptop that has Windows 7 64 bit.  She was not wearing the disc so had to download the drivers from the HP website.  Since she has downloaded the drivers, the computer not giving him stop, go to the Task Manager, or do much. I have check that she went to the site of HPs.  Has anyone else had problems with their computersw after installing the drivers?  I don't know what to do.

    Thank you
    Carla

    Hi Cmcgaw,

    Follow the steps below to completely remove the HP software. Let me know if you still have problems with the laptop after uninstalling the software?

    1. type % temp % in run

    2. look for a folder called 7z? Example: 7zS6D6F, and then open it.

    3. open the contents of the file Util

    4. open the folder titled CCC

    5. If you have an HP computer, run L3uninstall.bat. If your computer is not HP, then run the L4uninstall.bat

    6. once the uninstaller cleaning brush is finished, restart the computer.

  • problem installing drivers for WinTV-PVR-150/500. rpet pilots are not digtally signed after installing drivers. HELP PLZ?

    rpet pilots are not digtally signed after installing drivers. HELP PLZ?

    See this

    http://www.SnapStream.com/download/hardware/PVR-500MCE-installation.asp

Maybe you are looking for