Satellite P300 - problem after BIOS update

Similar Questions

• Satellite A500 emit after bios update 1.50

  Hey guys and girls,

  I have some problems after the update of the bios. Before the update my laptop has been the scene of much smoother and everything was fine and dandy until Tempro told me to update my bios. The problem is that after the update, the temperature seems to be considerably higher as usual when I play the game (I am a gamer) and also all the games I play seems to be much slower than before (lower, gal frame rate). Before the update I could play Dragon Age Origins with 1366 x 768 with 4 x anti-aliasing and the only one that I could get the same performance with the graphic parameter above is on 800 x 600. Now, it is certainly a big problem for someone who is a graphics junkie when it comes to games.

  * What do you think I should do? *

  A. downgrade my bios for when I bought everything first? (I don't know what version of bios is if anyone knows the stock bios?)
  B. perform HARD drive recovery?
  C. clean install of Windows 7 64-bit?

  My laptop computer spec:

  Model name: Satellite A500
  Part number: PSAR3E-00N005EN
  Serial number: X9206227K
  OS version: Windows 7 64-bit Home Premium edition
  BIOS version: 1.50
  Physical memory: 4096MB RAM
  Graphics card: NVIDIA Geforce GT 230 M

  Any help with this is greatly appreciated.

  Post edited by: Poyzen

  Hi mate

  I think you had a version of BIOS 1.30
  In older versions of the BIOS update are not available on the Toshiba driver download page. Only ASP (partner) has access to these early BIOS versions

  In any case, I found an interesting thread:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=50577

  Not sure if it could be useful but check

  PS; the graphics card driver update is a good idea it too check

• Unknown device on the Satellite A100-153, after BIOS update to 5.1

  ACPI\TOS1901 * TOS1901<--- this="" is="" the="" unknown="" device="" after="" bios="" update="" to="" 5.10="" on="" my="" satellite="" a100-153="">

  Vista now shows it in as unknown device manager; the TOS1900 showed up too, but after installation of Toshiba Value Pack for Vista, it went.

  Help, please. WHICH IS: ACPI\TOS1901 * TOS1901

  Hello

  ACPI-> Advanced Configuration and Power Interface
  ACPI defines hardware and software interfaces that allow focus on the OS configuration and power management to enumerate and configure motherboard devices.
  For example: ACPI is necessary for the standby and hibernation mode.

  Now your question; the new BIOS has been updated and configured to using VISTA.
  It seems that VISTA was not compatible with the previous version of BIOS because the ACPI interface. Now you can install Vista on the laptop, but it seems that you need a driver. Possibly new chipset driver version might help. But as you probably know, the drivers are not available at this time. Unfortunately

• Re: Satellite L500D - boot problem after BIOS update

  I downloaded the new version of BIOS (v1.4) official Toshiba site to update my computer Satellite L500D (PSLK0A - 00U009). But after the update, Windows 7 cannot start, Windows logo appears for a while then it restarts automatically. Windows then goes into repair mode. I followed the instructions on the screen to fix. But it does not work.
  When I reinstalled Windows, the computer worked fine until Windows Update told me to restart the computer. The computer dies again.

  I think that this version of BIOS has a problem. I wonder if there is a way to downgrade the BIOS to the earlier version. I found some instructions on the net to use the Phoenix recovery disk, but I have no file disk and BIOS.
  Please Please HELP, very appreciate.

  TKS

  Try to install the OS to help original Toshiba recovery image. After disabling automatic Microsoft updates to install. When you get the message about controlled initially available updates and install important updates only.

  Check it once more to see if the same thing will happen again. Display the results.

• Satellite Pro A200 - problem after BIOS update

  Help!

  Tried the BIOS update, got the screen blue, computer laptop doesn't work anymore, any chance I can reset the BIOS?
  Sorry for the vaugeness of the position enough to receive the message without reason below

  "Your message contains profanity or inappropriate language. In the interest of your fellow forum users, we ask you to change your message. »

  Hello

  I'm sorry to hear that. It's a really bad situation now. Unfortunately, I do not believe there is something you can do alone and I'm afraid that you need professional help.
  The best thing you can do is to contact the nearest authorized service provider.

  They can help you.

• Re: Satellite - blue screen after BIOS update

  Hello

  My computer laptop girls worked very well until I did the BIOS update this morning. Now, I get the blue screen of death STOP: 0X0000007F. Help, please

  concerning

  Carol

  Hey, Carol, welcome to the forum! :)

  Don t misunderstand me, but may I ask why you n t post more information about your problem?
  Important to know is that your laptop you have exactly and where to download the updated BIOS and for what model. This is important information.

  By the way: have you ever tried to load the default settings in the BIOS after update?

• PAVILION NOTEBOOK 15 K7Q21EA #: SCROLLING WINDOWS PROBLEM AFTER BIOS UPDATED 10 (08/03/2016) PAVILION 15 YESTERDAY 16/10/2016

  CANNOT CONTROL THE SCROLLING. CURSOR DOWN TO THE LOW WHAT MAKES IMPOSSIBLE TO SAVE TO A FOLDER

  Hi @STICKMAN5124,

  Nice day! Thank you for your participation in the Forums of HP Support! It is a great location to get resolutions and interact with experts from the community. It will be a pleasure to help you.

  I saw the post and understand that after only a bios updated cursor drops down due to a problem of scrolling.

  Impressive work, do the update of the bios. Kudos to you for this. It is a privilege to work with tech-savvy and technically competent customers like you and we greatly appreciate your business with HP. You have been great to work with.

  Please check in F2 diagnostics if the scrollbar works correctly. If Yes, then you can update the chipset drivers and http://hp.com/drivers touchpad drivers you can also consult with a mouse external further isolate the issue.

  You can also run diagnostics on the touchpad from this link by going to the UEFI F2 diagnostics: http://support.hp.com/in-en/document/c03467259 please run the complete components. If any component fails, please note the failure code. This is done to determine if the problem is hardware or software partners.

  If it passes and scrolling works very well, please perform these updates. If you are still having the same problem on page F2 UEFI (screen) then you could roll back bios after performing a hard reset. Link for the hard reset: http://support.hp.com/us-en/document/c01684768

  • Please perform this step to roll back bios.  Hold down the "Windows" key and the letter "B" at the same time, then press the power also button for about 5 seconds at the same time.

  I hope this helps. I would like to know how this happens. I hope the problem is solved without hassle and the unit works very well.

  Just to say thank youPlease click the ' Thumbs Up ' button to give a Kudos to appreciate my efforts to help me. If it helps, Please mark this "accepted Solution" because it will help many other people with the same problem to get it resolved without hassle.

  Now carefully and have a wonderful week ahead.

• Satellite A500 - overheating after BIOS update to 1.50

  Hi, I hope someone can help me.

  I updated the Bios to version 1.50 a few days ago and now the laptop overheats and stops after a few minutes, when I play a game (Day of Defeat Source btw, it is not the newest and shouldn't be a problem). This problem occurred for the first time after the update. There was no problem with the temperature with V1.20 before.

  Is it possible to downgrade the bios V1.20? Where can I download the necessary file? I can just download the latest version on Toshibas website.
  I have already asked the support of aid, but they did not send me a response up to now...

  Thanks for your replies! :)

  Hi Flex Barker,

  Are you sure that this problem is really caused due to update BIOS? Normally, these overheating problems are caused by the old thermal grease or dust often due to the radiator. In my opinion, you should try to clean your laptop using a jet of compressed air. This could blow out the dust from the cooling fans.
  Check this box!

  Downgrade of BIOS is normally not possible. Older versions of BIOS, you can get your local authorized service provider. :)

• UEFI problem after BIOS update

  Hello

  I've recently updated the version of BIOS for the Envy 15 J049TX.

  After the windows update shows "not properly configured SecureBoot.

  Please suggest a solution

  Hi Provost,

  I'm happy to announce that I have overcome the problem of activation of the SecureBoot. I saw an option in BIOS-> setting-> 'HP Factory loading key' Boot. After I loaded the default keys to toggle SecureBoot option has become active and I was able to activate SecureBoot. I applied the last update of the BIOS and has been able to activate SecureBoot successfully after the update.

  I wanted to know if this method is safe and that there can be no other effects on the other parts of the system.

  Thank you very much for the help.

• Tecra 8100 problem after BIOS update

  Greetings
  I have a tecra 8100, 700 mhz with 256RAM,.
  and it works a treat, until I decided to update the BIOS, the date of the previous version was 1999!

  As I run an OS linux on this unit, I downloaded a version of the Bios boot image and loaded on startup, it reported the success of the update.

  My problem now is that the system starts fine but extremely short slow,.
  It takes 15 minutes to start and is virtually unusable.

  I ran several tests of comparative analysis and tests of memory of Hiram boot CD and the only problem in the report was my 700 CPU running at 114.82. And of couse running, the CPU runs at 100%.

  I deleted the cmos data and be restarted using the default BIOS settings.
  Long searched the net and cannot find an answer.

  Help, please.
  was soon Munka

  Post edited by: munka

  Hello

  I visited the European driver of Toshiba page and found the latest version of BIOS that is 2, 50 - WIN.
  Do you use it?

  The BIOS can be updated only run under windows! That's why I m surprised that you were able to update the BIOS, the Linux operating system running on this computer.

  Try to download the most recent BIOS version and update as described on the help page of the BIOS update.

  concerning

• Black screen on the Satellite A100-712, after Bios Update

  I bought a new Satellite A100-712 and I did a bios upgrade, everything was fine in windows and restart the laptop got it is pasted on the toshiba black screen that appears when you turn on the lapto.

  Any suggestions please, I would be very grateful

  It doesn't sound good. I did the BIOS update on two laptops A100 and everything was OK. Sorry, but I think that you will not be able to do anything alone. I recommend you contact the service authorized in your country as soon as possible.

• Satellite A660 - 190 (PSAW0E) some problems after BIOS update

  Hey,.
  After updating the BIOS for my Satellite A660, I have some problems with toshiba apps 2:

  * 1. HWSetup - is not working. When I try to open it there is an info: *.

  + "Microsoft Visual C++ Runtime Library
  + This application has requested the execution to terminate in an unusual way. +
  + Please contact the support team of the application for more information. » +

  * 2. FN key is not working *.
  (a) after the installation of the package of added value + Toshiba Wizard cards Flash Utility
  * When I hit FN keys I don't see the keyhelper on the screen, pressing FN + F6 or F7 or others - there is no action
  * the keys are not working and I can set up and then

  (b) after uninstalling VAP + Assistant Toshiba + cards Flash Utility
  * When I hit FN key I still don't see the keyhelper, but I can change for example brightness by pressing FN + F6 or F7
  * the keys work correctly, but I can't configure the

  Anyone can solve this problem WITHOUT having to reinstall the system?

  Toshiba Satellite A660-190 (PSAW0E)
  Microsoft Windows 7 Home Premium

  Hello

  Try this:
  -Uninstall the VAP and Flash memory card Support utility
  -Install CCLeaner and clean the system and register using this tool
  -Now reboot the laptop and install the latest version of VAP. Use the VAP Advanced installation option and check if all the components of VAP are checked.
  -After installation of VAP, restart the laptop and test the FN keys.
  -If the FN buttons would not work, install Flash memory card Support utility.
  -Restart and test

• Re: Satellite L500-1XL - display problem after BIOS update

  Hello!

  I recently received a Satellite L500-1XL, works fine until I gave it to my friend...
  The problem is that he has updated the bios to V 2.10 (don't know why) and since then, the image on the screen appears as 15.4 "even in the bios.

  Any ideas what could cause the problem?

  Thank you

  Can you please make a picture how he looks in and post here?
  2.10 is the right version and I really put t understand what is the problem.

  Toshiba welcome screen appears as usual?

• Some problems with the LAN on Satellite L10 card after BIOS update

  Hello

  I have a problem with my satellite L10. Map does not work after the installation of the new network of edge of Bios (2.80).
  I tried it on Linux, BSD and WinXp. OS see my net card.
  I can even install parameters and ping 127.0.0.1 and my ip.

  But all the other pool spoke to me query time-out.

  Help me please.

  Hello

  What to say I put t think that this could be linked to the BIOS. First of all, as you said that the LAN card is recognized correctly in the device if Manager she s works well!

  However, you could try to access the BIOS and could set the BIOS default settings. Don t forget to save changes to BIOS ;)

  In addition, it would be advisable to reinstall the NIC driver. The Toshiba driver page provides the Realtek LAN driver v5.618.1015.2004.

  Good luck

• Satellite L500-1ZP - sound problem after bios update

  Hello

  Yesterday the update of the bios is installed and everything went well. The only problem is when I now plug in my headphones, the sound also comes through the laptop speakers. Before the update to the bios that the headphones sound when I connected them.

  What can I do about it?

  I have Windows 7 x 64

  Thanks in advance.

  No problem, buddy! :)

  But thank you very much for this useful information!