Satellite P750-0MQ - rocking when civ5 running problem

Similar Questions

• Satellite P750 - Wireless disconnects when wake the portable computer from the 'standby mode '.

  Hey

  Today, my Toshiba Satellite P750 (running Windows 7) has been disconnected from my wireless network when I wake from sleep mode. When I close the lid of my laptop, it goes automatically into mode 'sleep', and when I open it, I put my user password and use it as usual. However for some reason any today, it does not work.

  When I wake up, it recognizes my wireless network is available, however, cannot connect to it. When I solve the problem, it indicates that there is a problem with my router and I should turn it off, wait at least 10 seconds and then turn it back on. I tried this and it works fine, but my laptop has never done that (in the few weeks I got it) and I wouldn't constantly reset my router to use Internet. In addition, I have another laptop at home that works very well.

  Should be really this issue be resolved quickly as I have exams this week.

  See you soon

  Hello

  Maybe there is a problem affecting the IP automatically once the laptop has been in sleep mode. It could also be another reason for it but it of always difficult to say which could affect wireless networking

  I think you should try to update the Wlan driver.

  Don't know exactly what you have but here the card Wlan, you can find all the latest WLan drivers available for Toshiba laptops:
  http://APS2.toshiba-tro.de/WLAN/

  Uninstall the old drivers first, after new reboot install new drivers downloaded for the wireless network card that is built in Notepad.

• Satellite P750 - interference TV when connected to power

  I have a Satellite P750 (PSAY3A - 02L 001) that has a built-in TV tuner.

  Whenever I plug the power adapter into the laptop, it creates interference on TV reception. Without the adapter is connected, the reception is very good. I also checked at the reception of the antenna with a decoder and it is the signal strength of 90 to 100%.

  Help, please! Is this a faulty power supply? Or receiver defective tv? Or a driver/bios problem? Or just a bad design?

  I noticed similar problems on the external monitor, but I have a laptop.
  In the end the issues was grounded.
  Here's a thread on a similar problem with an external display.
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=40338

  in this case, the AC adapter cable was defective
  You should also test it could also be that you need a cable 2-pin, so the power adapter is connected to the Earth is no longer.

• How to calibrate the battery for Satellite P750

  I have a Satellite P750 seems to also have a problem with the battery when it is asleep and NOT trendy
  She stops going flat in about 3 hours.

  Nothing connected except a dongle for the mouse. And he sleeps there is no display going.
  It is a few months old... I think it can be calibrated

  Can someone please tell me how to recalibrate the battery.

  Thanks in advance

  Hello

  You can calibrate the battery very easily.
  Disconnect the power adapter and leave the laptop disconnected until the battery is completely discharged.
  Then plug in the power adapter and charge the battery until the battery indicator (LED) would turn to green.
  This must be done and repeated 2 - 3 times in the line.

• Satellite P750 - after update BIOS CPU fan runs faster

  Hi all

  On my Satellite P750 (PSAY3A - 02L 001)

  Since I've updated my BIOS to version 2.40, I noticed that the CPU fan runs much faster then normal.

  Even more, when I go in options inside BIOS configuration, saving it comes up with "an invalid entry.

  Has anyone experienced this problem? Know a way to solve this problem?

  In General, old BIOS is not available when one is offered on Toshiba new download page.
  If you have older version of BIOS try to contact the nearest Toshiba service provider and ask for help. They have access to the database of Toshiba and can get the ld for you version.

  By the way: have you tried to change the power settings for the cooling method and less upgraded?
  This should reduce the activity of fan cooling.

• Satellite P750 - 10 c: HARD drive slows down - Sandy Bridge Cougar problem?

  Hello

  I have problem with my notebook Satellite P750 - 10 c with S/N: 4B478828K.
  When I enabled AHCI in the BIOS, computer slows diametrically, day after day was worste and worste, so I tried to change from AHCI to IDE and it helped a little, but is still not good.

  I tried to restore my system, but it did not help.
  I read that Intel has released a version tapped for Sandy Bridge chipset, I have (HM65) SATA 3Gbs problem (I just checked in HD Tune and HARD drive is connected to the port of 3Gbs), so I think I got bugged version.

  My laptop is not guaranteed, but Intel said they changed valid version, so where do I return my phone to fix.

  Kind regards
  Tomek

  > I read that Intel launched buggy version of the chipset for Sandy Bridge.
  The problem was a Cougar Point of Sandy Bridge chipset and not the main processor Sandy Bridge.

  In addition Intel said that this issue affected only the SATA 2 to 5 and not ports 0 and 1.
  Most laptops use only two devices SATA (HDD/SSD and ODD) using the affected ports 0 and 1.
  That is why I think that your problem could be linked to the issue of Cougar Point the Sandy Bridge chipset.

  By the way: not all Intel Sandy Bridge chipsets have been affected.

  Regarding your question:
  Usually if AHCI is enabled, the HARD drive must use the performance of SATA. If compatibility mode, the HARD drive would go at the speed of the IDE.
  I think your problem is perhaps related to the problem drive HARD and not Intel problem.

• Satellite A30 stops when you run Norton

  Hello. I have a Satellite A30 which crashes when trying to run Norton.

  Spec: Satellite A30, Win XP Home SP1, 512 MB RAM, 3 + Ghz processor.

  We also noticed that the fan seems to be "fully enlightened", even when he's just sitting on the desktop with any of the applications that are running.

  Any ideas?

  We noticed that there was a notification for install of XP SP2, so we clicked on that. He started to install, the fan is even harder, it crashed again and now there is no notification of XP SP2!

  We are sure that this is a problem of overheating or battery, but we wonder what we can do about it.

  I hope someone can help. Thank you.
  Nath.

  Hello Nath

  As far as I know that satellite A30 is about two years old and agree to your description, I assume that the unit needs to be cleaned. I have Satellite P20, also more than two years, and for a short while I cleaned. You can't imagine how much dust was inside. I have a cat at home and I think half of the cat hair was inside.

  After cleaning, the laptop can take a breath and it works more silent. Now, I am very satisfied. I can just recommend you to do the same.

  Good luck!

• Satellite P750-13N - problem switching between nVidia and Intel GPU

  Hello

  I used my laptop Satellite P750 on its default settings because I brought and until now that has been very well.

  I use it mainly for games and now some of the more recent games have a hard run Shading.
  I used * www.systemrequirementslab.com/cyri * and he told me that I should be able to run most of these games without any problem.

  I checked my specs in dxdiag and noticed that it seems to be using the integrated graphics card Intel rather than the Nvidia Geforce GT540M map. I tried which helps the card in the Device Manager and disable the Intel graphics card, but the resolution has dropped drastically and dxdiag says there is now no graphics support found.

  I did something wrong or do you think that there is a problem with the laptop?
  Any help would be most welcome.

  Thank you

  This can be done in the nvidia Control Panel.

  + 1. Click Start, then Control Panel. Select Classic view in the left side of the window. +

  + 2. Double-click NVIDIA Control Panel. +

  + 3. Click view, and then add the "Run with graphic processor" Option to the context Menu. Close the NVIDIA Control Panel. +

  + 4. Right click on the title of the application and select run with GPU. Then, click processor high-performance NVIDIA. +

  Found this in this thread:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=67755

• Satellite P750 - overheating when using the graphics card

  I have a Satellite P750. I have a few games that I love to play, but I am unable to because that laptop overheating during the execution of these games.

  The specifications of the P750 with GeFORCE 540 m graphics card and 8 GB of ram easily meet the requirements of the games (Counter strike source, cod mw3).

  While playing the games for about 10 minutes, all right.
  After this step, things start to warm up, and small defects appear on the screen.

  Small rectangles of messed up graphics.
  If I don't leave the game immediately, I get a BSOD with errors such as "IRQL _less_than_or_Equal.

  The vent on the left side of the laptop runs very hot when this happens.
  I cleaned dust vacuum on and uses a fan/cooling pad to try to cool it.
  Makes no difference.

  I updated to BIOS and graphics card drivers

  WHAT CAN I DO TO PREVENT OVERHEATING WHEN YOU USE THE GFX CARD

  Hmm using the page of the Toshiba driver graphics driver?
  Such driver is a bit different from the other nVidia drivers because it s modified for mobile use. It contains some kind of overheating protection.
  In case of higher temperatures of GPU, such driver would clock down GPU performance in order to increase the temperature of the GPU.

• When I run Mozilla Firefox I get the error message "ReferenceError: Globalstorage is not defined." How to solve this problem?

  When I run Mozilla Firefox I get the error message "ReferenceError: Globalstorage is not defined." How to solve this problem?
  -Vinayak

  GlobalStorage is no longer supported in the current Firefox (removed in Firefox 13), versions so the extension or Web site that uses it needs an update and use localStorage instead.

  • https://developer.Mozilla.org/en/DOM/Storage#globalStorage
  • bug 687579 - Remove support globalStorage

• Problem reading with film in Blu - ray 3D on Satellite P750 / 02Q

  Hi all, I recently bought the laptop Toshiba 3D (P750 / 02Q). In my attempt to watch a movie on Blu - ray 3D, he failed twice. I received a message 'is not capable of reading 3D screen connected to your player. On the other title 3D Blu - ray, they say somethng in the lineage of I don't have a 3D player.

  I use the WinDVD pre-installed for Toshiba, version 10.0.5.822
  On the NVIDIA site, in the section "Download the Drivers", the current version of the driver installed in my computer after completing a sweep, is 267.44. There is a new driver available for NVIDIA GeForce GT 540 M 275.33.

  I'm not sure if this wil solve my problem. I also hesitate if I need to contact support for drivers certified for my laptop Toshiba. The P750 / 02Q is a recent model of liberation and I find very little support on the mytoshiba site.

  Hello

  I found a few Toshiba FAQ s on 3D technology:

  3D videos on your internal LCD or external 3D via HDMI port TV
  http://APS2.toshiba-tro.de/KB0/TSB0B032B0000R01.htm

  Since it is an Australian model of Toshiba, I suggest check this Toshiba driver page:
  http://www.MyToshiba.com.au/support/computers/satellite/P750/psay3a-02q001/download?OS=25

  Here you must update the driver display and Toshiba Video Player

  Take a look here also:
  Impossible to play 3D BD movies
  http://www.MyToshiba.com.au/support/item/436

• Problems with DAQmx - tasks missing when I run my application on another PC

  Hello

  I use a NI USB 6009 and my program use DAQmx and different tasks for the input and output signal.

  I created an application and I want to run this application on another PC, which doesn't have the development environment, but the runtime engine and installed MAX. This PC is connected to the NI USB 6009.

  Now, I have the problem that the tasks are missing on this PC and I get errors when I run the application.

  I wonder why these tasks are not put into the application automatically? What should I do now? Can I somehow export tasks in MAX and copy them to the other PC? Is not complicate it?

  Hi Johannes,

  Have you created your tasks of measurement and Automation Explorer?

  If this is the case, you must export the file of configuration of measurement and Automation Explorer and then import it on the other computer.

  With LabVIEW 2010, you can import a configuration via your Installer file, but I don't know if you can do it with LabVIEW 7.1

  Kind regards

• When I run Fix it is indicates a problem with Windows Update, says that it suits him but will show the same failure over and over

  Running Windows Vista SP2 and IE 9.  When I run Mr. Fix - It on Windows Update, is shows the components of Windows Update must be corrected.  I am hosting the program solve the problem.  If I re - run the same test again once, he does the same.  I have the other problem of breakdown on race fix it on any other criteria.  When I run the fix - it on Internet Performance and security, it shows my data execution Protection is disabled and my Smart Screen Filter is off.  Both are activated.  If I let the program Fix - It problems, even if they are correct, Fix - it continues to fail.  Any ideas?

  Hello

  I suggest you according to the question in this forum and check if that helps:

  http://social.Microsoft.com/forums/en/fixitcenter/threads

  It will be useful.

• Problem when I run an application

  Hi, I have a problem when I run an app in the Simulator. When the application is sync for the Simulator the following error appears:

  "Synchronization, and start the application has encountered a problem.

  result::Failure 500 'ascii' codec can't decode byte 0xc3 in position 104: ordinal not in range (128)

  I use OS X 10.9, Momentics 2.0 and system of the Simulator version is 10.2.1791.

  Thank you.

  Please check that you deploy a file binary (x 86) Simulator and not a binary system (arms).

• problems of the admin: message saying insufficient privileges: you must be an administrator when you run this application for the first time

  I bought this new comp with windows 7 already installed. has worked fine up intill a week or two it y a. I installed a new game, and after installation, I press launch to play it and pop up with a message saying not sufficient privileges: you must be an administrator when you run this application for the first time. also, I thought that I must be the administrator when I tried to launch the disk defragmentation. my account is the administrator account so I don't understand why they say that.

  I'm sorry. I was reading through additional FAQS regarding the same problem. I saw where someone said to try to add another admisistrator account to try to take on the former. but I had no luck with this ether. I also downloaded the program of the UAC, and I turned it off, reset my computer and still no change to my problem. I also tried to download the MSE restore tool, but I found myself with a message saying that I have no MSE

  Sorry, the MSE tool is to set the MSE when its broken.
  UAC controller Tool v1.0 can be used to control the
  The UAC settings.

  However, I suggest you restart the PC and after BIOS hold the F8 key
  and when the Windows Startup Menu appears, select Mode safe mode with networking.

  Now, you will enter Safe Mode. On the page to connect, you will see the
  Standard Windows administrator click it to open a windows session, press and hold
  in mind, the password can be blank.

  Once you have done that make a new account administrator and giv it a name.
  Restart the PC. That you did this newspaper using the new account.
  Once you have done that decide what to keep with your current administrator
  account once you've done it restart the PC, BIOS hold down the F8 key and
  Select Mode safe mode with network and enter dependencies the Standard Windows administrator.

  Go to control panel-> user accounts control and security for the family-> user accounts, then
  Select manage another account. In the list, select the administrator account
  your select and then delete the account, then it will ask you if you want to keep
  files etc, it's your own decision. Itknowledge24.com