Satellite P875 - 32L - is unable to reconnect to the last connected WIFI access point

I have a problem to reconnect to the last connected WLAN provider, with my Satellite P875 32 L.
WLAN is switched on and shows all the neighbors access points, but it fails to whoever I logged before the reboot, or before you go to the rescue of the list.

I'm going in service options for WLAN, sometiimes up to 5 times, then it undermines meet usually.
It's well annoying.

I have had this with the other 30 satellite of P870 too, but something so this behavior have disappeared. So there must be a solution.

Hello

You're talking about your private Wlan at home?
If you had the same problem using another laptop too, it could be possible that this isn't a problem with the network s laptop wireless card or Wlan configuration but with the WLan router.

You should definitely reset/reboot the rooter.
In addition, check the settings of the IP router and or mac address filtering.
Change also the type of encryption and Wlan channel.

You have to try different combination turn off just to test the WiFi encryption and check if the laptop would connect to the Wlan open correctly.
But the Wlan encryption must always be defined in order to avoid improper use of the Wlan access point.

Tags: Toshiba

Similar Questions

  • ESXi 5.5 build 2456374 is unable to reconnect to the vcenter after reboot

    Hello

    Have been hitting my head against it for the past few weeks. A host that has worked very well to a previous 5.5 build fails to reconnect to the vcenter after reboot once upgraded to build the 2456374. This also happens to the newly built guest. When a reconnection is started manually, it produces up to 80% (data of the host processing), then dies with a "general system error: internal error. I tried to remove the vpxa account, resetting the config network via the console, Cup NIC of the vswitch, removal of additional interfaces vkernel. The network via the console configuration reset allows me to reconfigure the net and tie vcenter and complete the host host configuration. However, as soon as I restart the host, is no longer, it reconnects to vcenter and I'm back where I started.

    Unfortunately, this is not a 100% event. If I rebuild a host enough times, one of the new buildings will finally works correctly.

    any ideas on how to solve this problem would be appreciated.

    Elmārs

    QUESTION REOLVED!

    Ok. so that was the easy part. Open a folder with vmware to identify the cause for this. After much digging, friction, pull hair, we found a clue in the hostd.log on the ESXi host.

    2015-04 - T 02, 04: 49:05.481Z [23381 B 70 error 'Hostsvc.NetworkProvider' user opID=HB-host-185064@917-1d029f4d-d2 = vpxuser] an error occurred during extraction of stack instance configuration: incompatible value of ccalgo for the Netstack instance: defaultTcpipStack.

    In my network performance test I did recently, I have significantly improved network iSCSI performance from the cubes NewReno network congestion control algorithm. For each of these hosts, as part of the installation procedure I now set the control algorithm of congestion on cube through the web interface. Finally, it is a little bug with that VMware believed fixed. Is not.

    To confirm doubling you encounter this problem, connect to the host (ssh or remote cli) and run the following command:

    list of esxcli ip network netstack

    You should get a message saying that there is an inconsistency in the netstack configuration.

    To fix, run the following command:

    esxcli network ip put netstack defaultTcpipStack cubic n - c

    the netstack from above list command should now display detailed information and will now be able to connect to vcenter.

    If I understand correctly, an article will be published on this in the near future.

  • Satellite A500 - 1 GB - copy dialog crashes on the eSATA connection

    Hello

    I have trouble when using my Samsung storyboard (1.5 TB, eSata/USB 2.0) with the Satellite A500 - 1 GB (Windows 7 64-bit):

    (a) when you use the connector eSata (preferred):
    The drive is recognized by the system, and I can read the directory information. But I cannot copy or play the disc. The copy dialog box freezes quickly and cannot be terminated easily.

    (b) when you use the USB connector:
    It is also recognized by the system, but copy and read operations take ages - I have tried to make a backup of the system, but cancelled after 5 hours.

    The drive works fine with another PC (also Windows 7 x 64), so the drive itself should be ok.

    I've updated satellite drivers today (BIOS, chipset and responsible storage), but this did not improve the situation at all.

    The question is probably, due to the 150 versus Protocol SATA 300 SATA? A500 - 1 GB does support SATA 300 (SATA 2) or just SATA 150 (1 SATA)? Is there a specific SATA driver (Intel?) I might give a try? Where could I check who is currently SATA-used protocol?

    Or do you have other clues on how I could solve this problem?

    Best regards
    Waschlappen

    Hello

    Theoretically, your external hard drive eSATA connection could be defective so have you tested the USB connection only on your other PC or eSATA too?
    In addition, you should test another cable, I had a USB cable, did the same problem and after Exchange of cable, everything was ok.

    There is no special driver for it on the eSATA connection. I think that it s part of the chipset driver for reinstall the chipset driver could also be helpful.

  • Satellite P875 - 32L - missing some drivers Win7

    I installed Windows7 on my P875 satellite. 4 drivers, it cannot find
    1-PCI-device
    2 unknown device Device
    3 unknown device
    4 VGA graphics Card

    The latter is a Geforce Graphics card previously requires an Intel driver. Why? No idea!
    I work as IT Manager and this laptop is urgent, can someone help me?

    Thanks, Narukami

    Hello

    I ve checked Toshiba download page on http://www.toshiba.eu/innovation/download_drivers_bios.jsp and your model of laptop (PSPLFE) is supported for Win7 64-bit, so you can find all the drivers, tools and utilities for your machine.

    You have installed all drivers from there?

  • Satellite P300-1GN is unable to save using the audio online

    Toshiba P300-1GN, win XP SP3, Conexant HD Audio - can't do this record from line-in, microphone (built-in & external) works well, but when select Line-In recording control there is no signal more!

    It is the brand new installation win XP with the latest Toshiba drivers.

    Any help?

    Hello

    Are you sure that this laptop supports the audio Line-In jack?
    As much as I know there is no such port.

    There is a headphone and external microphone jack.

  • Satellite Pro U400 BIOS update failed - what is the BIOS Boot-block access

    Hello

    My last update of the BIOS has failed and my laptop PSU45E PrU400 Satellite is now out of use.
    I want to use the recovery disk of crisis with a USB floppy drive, but I don't know the key combination to run the boot block.
    Is that someone can help me?

    Best regards

    Hello

    I was wondering what crisis recovery disk you have?  :|
    In my experience the special drive is required, which is available only for ASP technician
    That's why it of necessary to contact the ASP in your country to reflash BIOS.

    In my opinion you shouldn't t try recovery disks of the crisis who loves you in the net, it can drive to the mobo damage

  • Unable to connect to access point

    Like others my device cannot access my wireless router, when I turn on my camera it found my network and my network connection comments.  But I can't connect to networks using my device, it connects to all Free WiFi but not my network.  The attempts made with Lindys cat and I got the configuration wireless page and started to communicate when my text message were more visible on the screen, I was disconnected.  How can I configure my wireless router to open an access point on my Mobile device?  Help.

    What you see on this page is the information that you need to connect your mobile wireless.  Your mobile device must match the settings of your wireless router such as: SSID or network name, security type, and password.

  • Is satellite P875-L32 - possible to add a second HDD?

    I have a Toshiba Satellite P875 - 32L (PSPLFE-0C700RGR) which has 2 HDD / a MSATA SSD slot I would use now.

    My question is if they are enabled, or can be activated in some way to add storage capacity or an SSD for example a Crucial M4 MSATA SSD 256 GB. I asked the hotline and they didn t know. I wrote to the Austrian support and they didn t write again now I m really worried.

    I bought the Satellite as a model for my audio class. I chose for its storage capacity and will send it back if the slots are disabled, but I won´t think I mean after all Toshibas slogan runs innovation... and a slot for the disabled is exactly the opposite of innovation.

    I n t have this model of laptop, but every model can be improved with second HDD/SSD if square and the port are available.
    On the lower part there is only a single large enough coverage. When you remove it, you should see RAM and HARD drive. If it is necessary to drive HARD vacuum with SATA connector you can put there second HARD drive.

    You shouldn't be worried about anything whatsoever. Some models are extensible and others not.

  • Satellite A200-1vp with Vista - code 39 of the CD/DVD drive failure

    Hello

    I was burning and watch DVDs on my Satellite A200 - 1 VP, with vista, since February, the last time I burned anything was a couple of weeks.

    Suddenly, there is a problem, no response when I insert a disc and my divx player says me no recorder found.

    When I am looking in the Device Manager I get the message 'windows cannot load the driver for this hardware' (code 39) "driver is damaged or missing.

    I tried to uninstall it and using the limit filter upper/lower of Toshiba, repair tool but on restart it still cannot install.

    Should I try the Toshiba Recovery Disc and lose a lot of that programs/files, as a last resort?
    Would this work?
    Anyone have any ideas?

    Here's an interesting article from Microsoft Knowledge:
    http://support.Microsoft.com/kb/270008/en-us

    You must first access the Device Manager and should remove the reader of CD/DVD from the list of devices.
    Then should access the registry and delete the Upperfilters and Lowerfilters completely from the following registry key values:
    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Contro l\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

    Reboot the laptop and check if the CD/DVD drive would work again!

  • Cannot connect to my Satellite A210 adapter for access point

    Hey everybody...

    I have a little problem with my wireless. We have some books and access point. Everyone can connect to access point except me. I have the Satellite A210-127. Do you know where is the problem? How can I connect to the access point?

    Thank you

    In a first time, you must activate WLAN antenna correctly. Upon first use WLAN switch and set it TO position (the LED will be ON). Next step is to use the FN + F8 key combination. Don't forget THAT WLAN is enabled.

    After this use please ConfigFree radar to see if the access point is visible for your laptop.

  • Unable to connect via the wireless router "problem with wireless adapter or access point" _

    Hello

    I recently replaced my old Toshiba laptop with a new model of Toshiba Satellite L500/033HNX, it installed Windows 7.

    The problem is that I can't connect to my wireless network. I am currently connected via Ethernet cable to my Linksys router.

    I had help from my internet service provider, the installation correctly the problem not because of the connection.

    I had a Linksys online support, the router is a wireless, model - WAG54G ADSL gateway, is not the problem of all the correct settings and other devices can connect via my wireless network. I ran Dr. connectivity several times and it is always impossible to connect, "problem with the wireless adapter or access point.

    OK, you're my next hope to solve the problem can you HELP Please!

    Hi, JoelbX
    I want to thank very you much for your support and effort do to help me solve this problem, but we receive have been, and I don't want to waste any more of your valuable time, so I am the son of closing and deleting of Tring in Microsoft Answers.
    All the best
    Tring

  • Satellite L500 - 1WG PSLS0E - impossible to reconnect wireless

    * Computer info: *.
    Satellite L500-1WG - Partnummer: PSLS0E-07502EN5

    Windows 7 Home Premium

    The drivers are up to date:
    -Microsoft Virtual WiFi Miniport Adapter version - date driver 21.06.2006 - 6.1.7600.16385
    -Realtek RTL8191SE Wireless LAN 802.11n PCI-E NIC - 30.07.2010 driver date version - 2017.2.730.2010
    -Realtek PCIe FE Family Controller - 23.06.2010 - version 7.23.623.2010 driver date
    I disabled the "allow the computer to turn off this device to save power" for all 3 of them.

    * Problem: *.
    When I start the pc, it connects to my wireless router as usual, but then after that 30-60 minutes it stops working. He always finds the wireless router and the signal is excellent (4-5 bars), but when I try to connect it gives me the error message that it is impossible to connect to my router.

    If I restart the PC, it is always impossible to connect.

    But if I turn the computer completely off and leave it for a while, it works when I start it again, which suggests that he may need to cool (we noticed that the computer is warm enough, and that the fan is spinning a lot... but that could have been the same before - just that we it has not noticed that it was not a problem)

    ... But if I only it hibernates and let it cool for a while, it does not work to reconnect when I start again.

    I did a test earlier: I started the computer and made sure the wireless connected - then I put into hibernation and he did it again, and after that, he was still unable to connect. Then I stopped had and turned on the right now - and then it works fine.

    It's the same question at the local library, but my in-laws it worked fine for 2-3 hours the other day.

    My other pc that runs on Ubuntu, works without problems on our wireless.

    Any ideas?
    -Is it a virus?
    - Or my card network is not able to take the heat (material)?
    - Or is this a bug of Windows/driver (software)?

    I plan to reinstall windows, but before crossing with whom I was wondering if it's worth the hassle... Is it a hardware error, and should I just go directly to the seller?

    What you can try is updated the BIOS. Latest version is installed on your laptop?

    Another question: where you find WLAN driver version 2017.2.730.2010?
    Toshiba's latest version 2015.1.0427.2010?

  • I could not update or install applications for weeks, so I disconnected my Apple ID and rebooted the phone but now I can't reconnect! The error is: unable to connect to the iTunes Store. I should w8 for ios10 and hope that it will be fixed by the new ios?

    I could not update or install applications for weeks, so I disconnected my Apple ID and rebooted the phone but now I can't reconnect! The error is: unable to connect to the iTunes Store. I should w8 for ios10 and hope that it will be fixed by the new ios? Cause don't want to reset my phone.

    You have tried: If you can not connect to the iTunes Store - Apple Support ?

    And I tried to do a soft-reset/reboot the phone?

  • Satellite P875-31Z - cannot remove McAfee Security Center

    Hey there, I have a little problem, and so far, I have not been able to solve.

    I was helping a friend who is not as tech savvy like buying me a laptop, and he bought the Satellite P875-31Z.

    Now, it comes with preloaded software McAfee.
    I was able to uninstall most of the unwanted Mcafee software, but McAfee Security Center won't go away.

    It appears in the windows 8 'remove program' - list, it does not appear in the list of app store windows, and even the McAfee Consumer Product Removal Tool (Development) get rid of it. Well, she at least got rid of photo tile, now it's just a blank tile.

    It is part of some software from Toshiba and I have to remove some software that is also crucial for the proper functioning of, say, the function keys?

    Push me a little crazy, first time, that I could not get rid of software ^^

    I m wondering really you have this problem. On my laptop Win8 Satellite preinstalled under programs and features, there are two outcomes for McAffe:

    McAffe anti-theft and McAffe internet Security. I imagine that the same has to be on this P875 too.
    What needs to be done is the removal of McAffe Internet security. After restarting the laptop remove anti-theft McAffe and uninstall McAffe Security advisor, placed on the desktop (right click). All that s.

    I did the same thing.

  • Re: Satellite P875 - 31 p - upgrade to Windows 8 Pro possible?

    As the owner of a Toshiba Satellite P875 - 31 p

    I have 8 Windows pre-installed, but guess that's the Standard edition and ask whether it is possible to upgrade to Windows 8 pro.

    Someone has had experience of this updgade?

    How can I find out which version of the Windows 8 operating system is installed?
    What product of Microsort should I upgrade.
    Can I buy a new Windows 8 Pro OEM license?
    Where to buy an upgrade of my existing (from Toshiba?) operating system

    Is an upgrade to widows 8 recommended Pro?

    Hello

    According to the info I found on the page of Toshiba, the laptop is preinstalled with common system of 64-bit Windows 8.

    If you want to upgrade this Windows 8 Pro version, you can buy the upgrade of Microsoft.

    But the question is if these updates would be really necessary for you...
    I dunno... This page and take a look at the details provided by Microsoft Windows 8 Pro

    http://Windows.Microsoft.com/en-us/Windows/compare


    You can see what are the benefits of the windows 8 Pro version would provide.
    Usually there is no big difference between Windows 8 and the Pro version.

Maybe you are looking for