Satellite Pro 2100 - works does not with 2 sticks of RAM

Similar Questions

• Satellite Pro A100 - it does not recognize 4 GB of RAM

  Hello
  today I purchased two 2 GB RAM Corsair DIMMS (DDR2 - 667 mhz) for my Satellite Pro A100.

  After that I updated the BIOS it detected the 4 GB of RAM, but the balance of RAM on the boot prompt checks only 3 GB of RAM. So I can use only 3 GB of RAM (I use ubuntu 64 as an operating system). When I try to RAM into another laptop, it works perfectly. A memtest86 + says check: no error. When I plug in a dimm in the laptop, it is correctly detected as a 2 GB dimm module (tested two DIMMs into the two slots on motherboard)

  Anyone else seen this behavior? For me, it looks like a limitation or a bug in the version of the BIOS.

  (The processor supports 64-bit (core2duo t5500))

  concerning
  Kai

  Hello

  What Satellite Pro A100 you have exactly?
  As far as I know that some models can only be upgraded to 2 GB of RAM.

  It's really not easy to say what is the reason for this because I m confused on the subject of what the BIOS recognize the 4 GB of RAM, but not the boot prompt.
  I'm not sure that maybe the modules are not compatible with your laptop. You can test other modules?

  Welcome them

• Satellite Pro A100: Bluetooth does not work

  bought a toshiba Satellite Pro A100... came with a built in blue tooth... al worked well... until 4moths to fight back my computer had to be repair he was expelled to the toshiba returned however restarted by bluetooth/service application are not on the taskbar.

  I am looking for the computer n found in system folders aside my blue tooth stack but how to make the blue tooth to work.

  Make sure the WiFi switch is on.
  Press + and select the bluetooth antenna.

  Check if your Bluetooth module has been correctly detected:
  -Open the DeviceManager (start-> Run-> "devmgmt.msc").
  -Open the section "system devices".
  -A "Bluetooth ACPI" device should be available.
  (The system has detected the BT module if this is the case).

  Install the battery last Bluetooth (= drivers + Bluetooth management software) v5.10.12T.
  You can download it here:
  http://APS.toshiba-tro.de/Bluetooth/redirect.php?page=pages/download.php

• Satellite Pro L50 - A does not illuminate

  Hello

  I took a few steps on this forum but no luck so far...

  My L50 - A Satellite Pro was working fine up until yesterday, but today, only it just won't turn on. A small orange led light appears when I connect to the power cable...

  That's what I've done so far-

  1 power cable removed
  2. using a needle, pressed force shutdown (stop) at the bottom for 10-12 seconds
  3. then I pressed the start/power button on the front for 60 to 70 seconds
  4. I have connected the feeder and then to new press button start / stop at the front for 60 to 70 seconds

  Yet the laptop does not start!

  any suggestions?

  Thank you

  Hmmmmmm... It is not easy to say what the problem is here.
  Have you used your computer laptop usual ot, you might update something?
  In general, there are steps that you did which could be responsible for your problem?

• Satellite Pro L50 - A - does not function keys

  Hello

  I just bought the L50, but the function button did not work. I tried to reboot, reinstall the utilities, but it did not help.

  I couldn't find the "restart flash card" also. Can anyone help?

  Thank you!

  > I just bought the L50, but the function button didn't work

  What system do you use or what system was preinstalled on this laptop?
  As far as I know a few L50 - A Satellite Pro have been pre-installed with Win 7 and Win 8 DVD could be found in the package

  The fact is that Win 7 and Win 8 are two different systems and different Toshiba tools are needed to get the FN button work.

  Your comments would be appreciated.

• Satellite pro 2100: System can not recognize battery

  Hello!

  I have a problem with my Toshiba Satellite pro 2100, after the upgrade to Windows XP Pro with Service pack 2, my computer is anable to recognize the battery. I also reinstalled Toshiba powersaver drivers on the CD and nothing is better.

  I can work on my computer normally, but it's awful when it sudddenly shot without saving anything when the battery is completed.

  What can I do? Thank you all.

  Blaz

  Hello

  Can you please check under Control Panel Power Options Properties power meter is an indication of the capacity of the battery.

  Also check the settings in Toshiba Power Saver. Under energy-saving Modes, it is running on batteries go Normal, and then click details. Check all the settings in power saving Mode.

  If your problem persists, please write again.

• Active state with menu manual not working does not with child pages

  I created a horizontal menu manual on my master page with two links (at WORK and about me). I did them manually as it was the only way I could work out how the style and the menu items to distance as I wanted. I created an active state that works for the main page WORK and the about me page.

  However, I have four child pages under the work, but when you click on one of them that the active State for labor (a green line under work) does not appear. When I return to the menu options to try to "solve" the problem and choose "All pages" all child pages appear in the main menu I want and does not solve the problem. I chose manual that I could put the line to show that under the term of WORK and not all field.

  Here is my Web site to demonstrate the problem: www.robertgreens.com

  Any help to fix this would be appreciated with gratitude!

  I managed to solve this problem (with the help of Live Chat Support). I needed to create an autour work and provide a 'normal' State which resembled the active state, so when you click on the pages of the child, it looked like work page parent menu (with a green line) below. This meant that I had to duplicate master page and do the same (deletion of the green line in the menu of work) for the words Me page. And now, everything looks the same: www.robertgreens.com

• Satellite Pro L300 - touchpad does not work

  Hi all that I need help urgent because it drives me crazy. First of all, I use XP PRO. My laptop is fairly new, only around the age of 4 months, I had no problem with it at all. I formatted my laptop yesterday and reinstalled all the drivers that I downloaded here:

  http://www.ISD.Toshiba.com.au

  and everything works fine except the touchpad. I have already installed shared, utilitarian toggle the touchpad Module and I have the latest BIOS installed and reset all default settings and I made sure that the touchpad is enabled in the BIOS, but also pressing FN + F9 to enable during Windows.

  I installed the latest touchpad driver Synpatics I downloaded from the homepage of Synaptics. But for some reason any, that it does not work, I don't know what is the problem here. My touchpad worked before I formatted my laptop, it worked fine and has never had any problems. Will you please tell me what is wrong because I need to use my touchpad sometimes as well, so I can't use a mouse all the time.

  Hello

  > I installed the latest Synaptics touchpad driver that I downloaded from the home page of Synaptics
  I think that you question refers simply to the driver for the touchpad that is missing or incorrect.
  I put t know how it works on Toshiba notebook Australian, but the Toshiba European Satellite Pro L300 units needs touchpad different drivers. some use the Toshiba touchpad driver and some units need a driver for the Synaptics touchpad.

  In your case, I recommend this controlled again.

  By the way; My touchpad is always disabled so that en external mouse is connected.
  It is parameters that control it. Please check in your touchpad properties too!

• Satellite Pro M10 - infrared does not work properly

  Hello

  I have a Satellite Pro M10 and my infrared does not work. I downloaded the zip file with the drivers from this site. Then, I uninstalled and reinstalled, but it always happens in the Device Manager under "unknown - SMC IrCC - Fast Port infrared (IR Module: HP). (with an exclamation point). When I look at the properties it says under device status:

  This device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

  Click Troubleshoot to start the troubleshooter for this device.

  However, under Driver Details is said:
  C:\windows\system32\DRIVERS\smcirda.sys

  I extracted the zip file in my home directory of c:\downloads\infrared.
  whatever I do, it does not now. It worked when I bought it, but I have too many things on the system for a new installation. Which brings me to another question. Is it possible to re - install windows without losing all your data, etc.? I did it with other systems (95,98) Windows. But it seems that the Toshiba recovery disc means any wiping.

  Thanks in advance for any help.
  Chris

  Hello

  If your HARD disk contains two partitions and you have saved the data on a second you can reinstall the operating system on the first partition using recovery DVDs.

• Satellite Pro 4270 - USB does not work

  Hello.

  I had this problem for a while, and I was wondering if anyone had any suggestions to solve this problem.

  I have more or less of work Satellite Pro 4270 (4200 Series) computer laptop with XP on it.

  The USB port does not work. I don't know why it does not work. I tried to replace the USB module on the motherboard that has not worked. I've updated the BIOS to the latest version, has not functioned. Removed and reinstalled the drivers in XP, not worked. I'm out of ideas.

  IrDA works very well.

  Some suggestions please. Thank you

  Hello!

  I understand, were you solder the module USB motherboard and then solder another module?

  I mean, what have you done with the module USB, replacing? Sorry, I don't remember exactly how the USB module is connected to my mobo SP4270 seen last about the half a year ago... If the welding, I don't wonder the problem... but if not, there may be a solution...

  Best regards

  Pete v.

• "SHIFT" on the Satellite Pro C660 key does not work

  G ' Day,.

  I have a little problem with my laptop Toshiba Satellite Pro C660.
  Unfortunately I had to remove the keyboard and thus dislodged the
  fragile plug to connect to the computer.

  The 'Shift' key refused to work since. All other keys work as usual.
  The only problem is the 'Shift' button does not.
  I tried to gently move the plug but made no difference so now have to
  Use a USB keyboard.

  Can you please help with suggestions for this problem?
  Thank you for your time.

  See you soon,.
  Sunrap.

  I really put t know what you think when you know that there is no connection for each unique key, but for the entire keyboard.

  To be honest I ve changed keyboard several times but never noticed this problem.
  Are the two SHIFT keys off function?

• Satellite Pro U400 - BT does not work after installing Win 7

  Hello.

  I have a problem with my bluetooth device. I have Toshiba Satellite Pro U400.
  My previous operating system was Windows Vista business and I just replace it with Windows 7.
  Since I installed it my device Bluetooth does not work anymore.

  I have had no problems with it with my previous Windows.
  Now, the following messages will appear: "Bluetooth stack for windows by Toshiba is incompatible with this version of windows" I have windows 7 Professional.

  I tried to update the drivers, but I was told that I have the best and latest drivers.

  Can someone help me?

  Hello

  Seems that you are still using an old battery Bluetooth.
  You this should remove the system and need to install a new one which you can download here:
  http://APS2.toshiba-tro.de/Bluetooth/

  You can find the pile of BT for Win 7 32 bit and 64 bit version

  Welcome them

• Satellite Pro C850 keyboard does not work properly and opens several programs

  My satellite pro C850 1HE keyboard intermittently stops working correctly, and begins to open programs, for example, by pressing F will open the file search, C open computer this kind of thing

  is there a permanent solution to this problem?

  This is not something to do with installed programs is not something to do with the browser settings.
  restarting the computer works in a short time, but that is a long time, it's really annoying because I use this for work and study!

  > is there a permanent solution to this problem?

  The question is what causes this problem? Is it related hardware or software related issue?

  Why n t connect a USB keyboard just to check if the same would happen?

  In case the USB keyboard would work fine, I guess that the internal keyboard failures and the solution would be a simple replacement of the defective part.

• Satellite Pro M30 - WLan does not work

  My Satellite Pro M30 laptop is about 5 years old and is a refurb. Until yesterday, my wireless connection was very good. Although my wireless connection is running with high speed and it is connected, I now cant get on the internet without using the ethernet cable.

  It is certainly a problem with the laptop itself.
  A framework has changed (perhaps with a function key?) or the internel wireless card packed.

  Can anyone suggest anything I can try with the laptop first before you buy an external wireless card?

  Thank you.

  I don't think there is that you can do.

  The wireless network card appears correctly in Device Manager.
  Make sure that the wireless network card is enabled correctly (FN + F8).
  There may be a problem with the WLAN antenna. Who knows?

  Anyway, if you can't get this to work once again use small USB WLAN adapter and be happy.
  To be honest, is not bad idea because new USB WLAN glue can work with G WLAN or even N. The original WLAN card in your notebook is, I guess, old A/b.

  Good bye

• Satellite Pro A300 - Webcam does not work in Windows live messenger

  Recently bought a Satellite Pro A300, with integrated webcam. However, when I try to use the webcam in Windows live messenger it comes up with the following error messages.

  * "We couldn't start your camera. Please check that your camera is not currently being used by another program, and then try again. » *

  Also this message...

  * "Messenger is not available right now. Please try again later. (0x82000009). "

  Now, the camera is not enabled, and Messenger works normally.

  * HELP! *

  Thank you

  Folic

  When you get the message if another program uses always the camera.

  So, try to disable the webcam software and other e-mail programs in msconfig.
  Restart the laptop and if you want to use the webcam software you need to start the first webcam software.