Satellite Pro 4200 overheating because the fan does not work

Similar Questions

• Satellite Pro 6100: error message - cooling fan does not work

  Hello
  I have a SP6100 and it keeps giving me an error message about the cooling fan does not. Then he tells me to stop immediately and runs very slowly. The fan come on, but after three or four short bursts it stops and the message appears.
  Is it a mechanical problem with the fan? I took out the radiator and the fan, and it was clean and not sticky.
  What is a system problem? The BIOS has recently been updated.
  Should I just invest in a new cooling unit and if so where would I get one?
  Any help would be greatly appreciated!
  Thank you.

  Hello

  I recommend to contact the ASP (certified partner) because it can test your device and can do a diagnostic test.
  You can be sure that the laptop will be repaired correctly 100%.

• Satellite M30-604 freezes and the fan does not work after replacing

  Satellite SM30-604. Laptop has left the mat from one day to the next and overheated! Fan won't spin and laptop start only occasionally. Thinking that the fan was fault I replaced the fan but even this new fan doesn't spin. The heat sink is totally clean - dust free inside the fins at all. The laptop is only 2 years.

  Cooling using forced (by sticking a nozzle of aspiration to the output of the cooling fan!) the laptop starts sometimes as normal until the desktop screen with all of the usual icons and no error message. But then, it does not further - the freezing of the screen, keyboard and mouse.

  Most of the time it does not start at all. When it does not start, the blue LED lights up but there is no hard disk activity or LCD at all - even the wifi LED lights even.

  Really grateful if someone knows what's going on. You are not sure if it is the main processor that is defective?

  Thanks in advance.

  Charlie

  Hello, Charlie

  As you know on this path is not easy to give an accurate diagnosis, but according to your assignment, I guess there is a complex problem and unit must be properly verified. I also think that there must be a problem with the electronics.

  It is really possible that the motherboard needs to be replaced but, as I already said, it is not possible to say something specific about your problem. Try contacting Asp and you will see what they say.

  Good bye

• Satellite Pro U400 - sound of the wheel does not work anymore

  The wheel of sound control in my Satellite Pro U400 works not properly since last month.

  Now, I have to use the volume bar in Vista to adjust properly. When I try to lower the volume by turning the wheel, as I did before, he constantly increases the volume after reducing to a few percent. If I flip it is very very slow, sometimes it decreases the volume a little, but other times it increases. Also when I'm in a word processor, turn the wheel to the right input 'c' character ' on the screen.
  There is no problem when I try to increase the volume, it does its job.

  Do you think it is related to hardware or can it be a problem of driver or something. Is there a solution?

  Thank you

  Hello!

  In your case, I would setup a pilot of his most recent. Search on the Toshiba site and check:
  http://EU.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download drivers

  I had this problem on another laptop Toshiba also and after reinstalling with the recovery disk the problem has been resolved. I also tried updating the drivers and so far, but without success.

  Good bye

• Satellite Pro 105-S9722 - why the touchpad does not work when it is the cover up?

  whenever I hit the touchpad icon to light up the touchpad, it won't work, only when it is off...

  Hello

  I m afraid. I put t understand what you want to make :(
  You want to enable the touchpad or what? Thanks for posting more details

  You can enable and disable the touchpad with FN + F9 key
  If you want to change some settings for the touchpad, so I would recommend getting into the mouse option in the control panel.
  That could be the touchpad properties.
  In the properties, you should be able to find the needed touchpad settings.

• Satellite P100-324 - GPU overheating due to fan does not work in the operating system

  Hello world.

  While trying to solve the problem of RAM of 4 GB ([this thread | http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=28374&tstart=0]), I meet another weird thing - gpu overheating due to fan does not work in the operating system.

  Now, I restored the XP MCE using the Toshiba Recovery and I was VERY surprised to see that the problem still exists! As soon as loading the system GPU fan stops, and there is only tranquility. The application load is heavy on GPU and reaching 104 results by reducing its GPU and MEMORY clock values and NOT in the activation of the fan.

  The same thing happens in 64-bit gentoo. ACPI can be turned on or off, it is not serious, the GPU fan always dies as soon as the system load. In non-OS environments (bios, program of recovery, etc.) the fan works fine, GPU cooling from time to time.

  This problem occurs in versions of BIOS: 2.40, 4.00, 4.20.

  Any help would be greatly appreciated, since this laptop is my main working tool and I can't let go 14 days (service).

  I saw in your other thread that you have updated the BIOS and you have installed several different OS.

  Fact is that the BIOS v 4.2 package contains BIOS 32-bit and 64-bit OS.
  Your laptop has been preloaded with Win XP MCE 32 bit. Please use the 32-bit BIOS if the original XP MCE running on the laptop.

  Best regards

• Satellite P850-30W - the fan does not work after returning from the mode "Eve"

  I have a Toshiba Satellite P850 30W with bios 1.90.

  Sometimes the fan does not work at all after back mode standby on windows 7.
  What happened twice (perhaps several times without knowing me), and Ive had the computers for a month.

  Normally the fan starts to run when the CPU gets more than 50 degrees celsius and stops less than 50 celisus...

  I tried running Prime95 when this fan-this occurs and the time of the computer got dangerously high (near 100 degrees)! the fan did not start at all
  .. .This error could damage the laptop potentinally...
  to get the fan turns once again I have to restart windows

  anyone experienced this?
  I guess that the fix would be to never use standby... or toshiba needs to fix it with an update of the bios.

  > Sometimes the fan does not work at all after back mode standby on windows 7.
  > What has happened twice (perhaps several times without knowing me), and Ive had the computers for a month.

  You said it's happened twice and only sometimes done this means that above all the fans are working well?
  In this case, this would mean that it of difficult to reproduce this problem, but you might be right: maybe a BIOS update would help solve this problem permanently

  I found some discussions on the stand-by mode and fan activity and in most cases, the update of the BIOS was the key.

• MacBook pro a key on the keyboard does not work

  Hello

  Last day I was cleaning my keyboard (I do not used any water or liquid), and when I handed the keys, I found that my 'enter' key does not work.

  I think it's because that material because the key does not work even without the key cover. Is it possible that I have demaged some buses on the baseboard of the keyboard?

  In addition, I can not open Apple Diagnostics, and while I turn on my macbook it produces sounds like that I am button constantly some.

  -Make an appointment at the Genius Bar to an Apple store to discuss your options.

  Shop Apple Store - Genius Bar

  This is the Office Mac Pro forum. I asked that your post be moved to the MacBook Pro laptop forum.

• Windows Update cannot currently check the update, because the service does not work, you may need to restart your computer

  My computer stops the update via WIndows Update Component

  Whenever a try to do the manual update using this component I get the message;   * Windows Update cannot currently check the update, because the service does not work, you may need to restart your computer *...

  My computer has a few updates, but can not run these update

  Whenever I try to run computer shotdown/updates remain frozen for a while and stops without updating

  He starts to run updates 1 of 13... and stops

  If I shutdown normal e, computer stay likehanging 1 hour without stopping.

  I would like to know how to solve this problem

  Thank you

  Concerning

  Gladmar.

  Hello

  Were there any changes made on the computer before the show?

  Perform the following methods and check:

  Method 1:

  I suggest you to check if you are able to access Windows Update service and ensure that the following services are started. If it is not started, follow these steps:

  a. click Start, type services.msc and press enter.
  b. search Windows Update.
  c. right-click on the service and select Properties.
  d. in type of startup, select enable.
  e. click Start under the Service status.
  f. click OK.
  g. Repeat steps c to f for the following services:

  Background Intelligent Transfer Service
  Cryptographic services

  If the steps do not help to solve the problem, you can go ahead with the methods mentioned below and check.

  Method 2:

  How to reset the Windows Update components?
  http://support.Microsoft.com/kb/971058

  Method 3:

  Your anti-virus software is in conflict with Windows updates. You can test this by temporarily disabling your antivirus:

  Disable the antivirus software
  http://Windows.Microsoft.com/en-us/Windows-Vista/disable-antivirus-software

  Note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

  Method 4:

  The problem with Microsoft Windows Update is not working

  http://support.Microsoft.com/mats/windows_update/

  See also:

  Troubleshoot problems with installing updates
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-with-installing-updates

  Updates: frequently asked questions

  
  http://Windows.Microsoft.com/en-us/Windows-Vista/updates-frequently-asked-questions

  I hope this helps.

• If I start Photoshop I get 3 error messages: 1. FastCore-Routinen-Modul 2. MMXCore-Routinen-Modul 3. Mehrprozessorunterstutzungs-Modul could not be loaded because the tool does not work with this version of Photoshop.

  FastCore-Routinen-Modul could not be loaded because the tools does not work with this version of Photoshop.

  The MMXCore Routinen module could not be loaded because the tool does not work with this version of Photoshop.

  The Mehrprozessorunterstutzungs module could not be loaded because the tool does not work with this version of Photoshop.

  Hi zimlo,

  Please check the below link which may help you:

  https://helpx.Adobe.com/Photoshop/KB/error-could-load-fastcore-multiprocessor.html

  Concerning

  Sarika

• Satellite Pro A300D - reinstalled XP - now its does not work

  Recently, I had a virus on my laptop Toshiba Satellite Pro A300D-14O, which meant that I had to take it to get reinstalled Windows.
  This tech guy who I gave it to a do.

  However, now, the sound does not seem to work properly.
  The volume on the laptop wheel itself does nothing.
  I tried to open Control Panel to check the sounds and audio devices, but I could not change anything in the boxes.

  I tried to download a driver from toshiba Web site was updated, but I thought that it could not find the device driver support.

  Can anyone help?

  Hello

  You must install the Win XP SP3!
  This package must be installed BEFORE installing the audio driver.

  Install SP3
  Then remove the audio driver (already installed) system
  Go to Device Manager and remove the sound chip of the list of devices
  Restart the device
  Now reinstall the sound card driver.

  Should work as it worked in my case as well

• Satellite Pro L10 - FN + F5 view command does not work

  When I attach my Satellite Pro to an external CRT, LCD monitor or projector, I get the same problem each end every time.

  the Fn + F key to toggle the display of control does not work.

  When I start the laptop with the attached external display device, everything is fine, and the display is exclusively channeled in the external display. but as soon as windows has started, the display switches to the screen of the laptop, and there is no way to make it back.

  y at - it an update for this problem, or another solution I know not?

  Thank you.

  Hello

  Seems to be a simple software problem.
  I put t know how long you OS runs on the laptop, but maybe some files registry entries are corrupted and therefore the FN key does not work as it should.

  Could help to reinstallation of the OS and the use of the recovery CD

• Satellite Pro A60: TV S-VHS on does not work

  I have a Satellite Pro a60 and I'm pulling out my S-VHS to function... This does not work very well.

  I connected all the cables right and right click on the desktop, again choose preferences, then on Preferences, but I can't find anything on the transmission of the video signal.

  I have not though as the configuration standard of Toshiba, but that shouldn't matter. I'm running WinXP SE, but the drivers for my card ATI is about two years old and I can not find a suitable one anywhere, this is the problem, or should I program utility ATI?

  Best regards!

  Hello

  You should also check the TV settings. You must choose the right channel.
  As in the previous announcement suggested, you can change the display device using the FN + F9 key combination.
  If you want to play the DVD with the WinDVD player for example if you first need to change the output of the TV and then start the WinDVD.

• Satellite Pro L20-212 - USB 2.0 does not work

  Hello

  I own a * Satellite Pro L20-212 *, * Windows XP (SP2) is installed, but USB2.0 does not work *. I see nothing on USB 2.0 in the Devicemanager and the speed of the USB 2.0 devices attached is at the level of the USB 1.1.

  I don't know what information is needed to help me with this problem as it should normally work on my laptop (and I know that the laptop has USB 2.0 ports).

  What I have to install a special driver to use USB2.0 or is there any software on my laptop that I need to activate?

  Thank you very much
  Frank

  Hello

  Did you install the image on the Toshiba Recovery CD? This image contains the Windows operating system, Toshiba drivers and additional utilities. After installation, everything should work fine, and also the USB ports should work also.

  The USP ports, you can find in Device Manager in the serial BUS controller universal section. Open the tree and check if there is some yellow exclamation points.
  Then try to remove the Device Manager, the controllers and the USB hub and restart the laptop. After restarting again the OS should recognize USB controllers deleted again.

  I hope that this accelerated procedure will help you.

  Greetings

• Satellite M70 - 170 - Touch and the launch does not work

  Hello everyone, I'm Sylvain and I'm french, so sorry for my English...

  I have a Toshiba Satellite M70-170, and I have a problem with the program "Hit and run" (1,2,9,0)

  I see the icon then the clock and I can change the settings, but when I press the button of the mouse will work, but not to the touch and launch...

  Can you explain why?

  I love this commercial and I want to know why it does not work.

  I put t know why the touch & launch does not work, but I would try to reinstall again.
  The Touch & launch is placed on the European driver Toshiba page.
  This time it s a v 1.2.9.0 for Win XP.

  Uninstall first touch & launch and after restarting again install it again!