Satellite Pro 6100 Wireless does not work after restoring from HARD drive

After that restore disks for installing a new HD and use and to update XP sp2, the Wireless does not work and if the card is installed XP hangs then works in fits and starts. If the card not in place, not bad at all.

Booting from a Linux CD, the card works perfectly! I assume that the driver is the problem. The wireless card is the original, an Agere MPC13A-20/R, with Toshiba p/n PA317U-1MPC.

I have found some drivers Agere, but am not sure

(1) if they are correct
(2) how to install since the machine works in a way limited with the card in place.

Any advice?

Hello

I checked the page of the pilot and the only available for Windows XP WLan driver is the driver of v.1.11.108 Agere.

(1) just try to install this driver. If the driver is not correct or is not compatible, then windows will not install the driver and you will receive a notification. You just have to try

(2) generally you may reinstall the driver from the Device Manager. Open network controller tree, and then you can reinstall the driver.

But this is only possible if the windows started successfully

PS: Have you checked the information of Microsoft Windows XP SP2 update on the page of the Toshiba driver.
I discovered that you need to update several utilities if you have installed SP2 on this laptop.

Tags: Toshiba

Similar Questions

  • Satellite T110-121 - Wireless does not work after sleep in Win7 Home Prem 64

    Hello

    I bought Toshiba Satellite T110-121, with Windows 7 Home Premium.

    Problem:

    1. after going into Sleep Mode, when he wakes up, my WIFI does not work, unless I'm in wireless network card setting, Advanced tab, then I change the Tx to say 100% to 75% power level, then the WLAN will work.

    2. I tried to adjust the setting for power management on the network card for maximum performance and does not disable during sleep and also in the Bios but nothing is

    3. I use Realtek 8191SE drivers have been updated (wireless card, Ethernet, Bios)

    Thank you

    As much I know Tx power level option must be set to Auto.
    Have you noticed the same behavior with Auto option?

  • Satellite Pro U400 - BT does not work after installing Win 7

    Hello.

    I have a problem with my bluetooth device. I have Toshiba Satellite Pro U400.
    My previous operating system was Windows Vista business and I just replace it with Windows 7.
    Since I installed it my device Bluetooth does not work anymore.

    I have had no problems with it with my previous Windows.
    Now, the following messages will appear: "Bluetooth stack for windows by Toshiba is incompatible with this version of windows" I have windows 7 Professional.

    I tried to update the drivers, but I was told that I have the best and latest drivers.

    Can someone help me?

    Hello

    Seems that you are still using an old battery Bluetooth.
    You this should remove the system and need to install a new one which you can download here:
    http://APS2.toshiba-tro.de/Bluetooth/

    You can find the pile of BT for Win 7 32 bit and 64 bit version

    Welcome them

  • Update of Vista 32 bit does not work after replacing the hard drive

    A month ago the hard drive of my computer (ACER Aspire 6920) had to be replaced. The disk image hard precedent (which includes the c: with Windows Vista Home Premium 32 bit, SP 2 build 6002) has been mirrored to the new hard drive. Everything seemed to work fine until I noticed that I don't have more updates from Microsoft. I tried a manual update and got the message that the update service was not working and I have to restart the computer. However, the Task Manager showed that the update service has been executed. Of course, I rebooted the computer, but nothing has changed.

    I found a whole bunch of recommendations for this issue in this forum, but nothing seems to work:

    • The Microsoft FixIT tool indicates a problem with the update of components, and then said that the problem had been solved successfully. However, the problem is still there and rerun the FixIt tool Gets the same message on a problem (yet) found and fixed.
    • I also stopped the update service, delete all content in Windows/C:\Windows\SoftwareDistribution and restarted the service. without success.
    • I've temporarily disabled my security suite (Eset Smart Security 6) and tried the update. I also have fittings the folder C:\Windows\SoftwareDistribution to the scope of the antivirus, without success. On the old hard drive, I used a different security suite so I thought that maybe the ESET (that I installed everything recently) could be the cause of the problem, but that doesn't seem to be the case.
    • I also followed the instructions provided by Microsoft at http://support.microsoft.com/kb/971058, but again, no change at all. However, it should be noted that registering some DLLs that Microsoft listed does not work (message that the DLL is not found or some server entry point (my translation, I'm using the German UI and don't know English good term; sorry) could not be found.)

    Http://support.microsoft.com/kb/947821 , I found another tool that supposedly can solve some problems of updating; I downloaded the version for Vista 32-bit, but it cannot install it on my computer (error code = 0xc8000247 during installation).

    So I'm really lost now what else to do. I would appreciate any suggestions. Please note that I am not technically very warned :)

    ARG, apologies.

    Was not aware that they had dropped support for Vista... (I myself have 'graduated' Vista earlier)

    The fact that you have not already installed TSRI is exactly your problem.

    Recent hard drives using 'Sectors 4 K', also known as 'Advanced Format Technology'.

    If the installed hard disk driver currently is not compatible with this specification,

    It will result in oddities like the status of the service Windows Update is not recognized correctly.

    Installation TSRI will fix this in most cases.

    Alternatively, if you are using Vista SP1 or later version (or 7 SP1), you can use the real driver.

    Since you are already updated to SP2, we will see if it is a viable solution.

    Go to: start-> Control Panel-> programs-> programs and features

    In the list of installed programs, locate and remove if found.

    -Intel Matrix Storage Manager

    -Intel Turbo Memory

    This should force your computer to go back to the real driver provided by Vista.

  • Satellite Pro 6100 keyboard does not work properly after repairs

    Hello

    My 6100 Pro Sam just being away from usual mother board and power Board replacement with Toshiba, but now I have a strange keyboard problem.

    When I turn it on, all the keys are working. After a few minutes, '3' is not working, then 'r' fails, then '5', ' 7 ', ' 8',' 9 ', ' 0' to stop working. At this point, I can feel something very hot under the middle of the keyboard. A reboot and no keys work. Another reboot with the internal keyboard and an external keyboard to the PS2 is still defective (some keys work, others do not), but the outer one works properly.

    Now, if the pc has not obtained if hot as the middle of the internal keyboard, then, I would conclude that the keyboard was defective, but for his failure, slowly and sequentially like this and it fails at the same way every day (since Toshiba rebuild it!).

    Perhaps, internal keyboard controller overheating?
    Anyone know what this could be? :-(

    See you soon,.
    Homer

    Right under the keyboard of your pro 6100 is the VGA graphics controller (the keyboard cable plugs on the same map). It is normal that this part become hot during use.

    It is strange that your problem appears after a while and not immediately.

    It could be just a bad relocation of the keyboard cable (it's a thin layer as a movie negative photo) which easily appears there, but... it may be something more serious, too. (Especially since you had done upgrade where the material had to be changed)

    I consult the service centre once more and ask for instructions how to deal with this. Do not ignore it (using an external keyboard instead of internal dysfunction) because he could end up in something more serious soon...

    Concerning

    chain

    P.S. Please keep us updated on your efforts

  • Satellite Pro A200: Wireless does not work

    Hello

    Got a Satellite Pro A200 2 weeks and the wireless worked well.
    Then after a week there was a problem, try to connect. I was able to reboot the pc and he was able to connect.

    Now it just doesn't quite work.
    I can connect through the LAN and I have another laptop that connects to the router with no problems.

    I checked in the Device Manager, the wireless card works correctly and I've updated the drivers for it but no. - GB.

    Any help would be great.
    see you soon

    Hello

    Try to remove the network adapter from Device Manager wireless.
    Then restart the computer and reinstall newest WLan driver that you can download on the page of the Toshiba driver!

    Second, you could try to set up the WiFi network using an Intel ProSet Utility (but only if you have a Wlan Intel card.)

    If you have an Atheros Wlan card, then try using the Atheros Client utility for configuring Wlan

  • Satellite Pro L550 - WLAN does not work after Installation Win 7/64 Pro News

    Hello

    I installed a true Win 7 / 64 professional version full on my Satellite Pro L550-199, PSLW9E. Now, I can't turn on my WLAN. There is no such thing as the large buttons-FN. I tried a lot of driver, that I found on the Toshiba Support page.
    Whitch is the right, or Win 7 / 64 professional not supported with WLAN?
    How can I pass on WLAN without the FN key?

    Lenny

    Hello

    To activate the WLan, you need to install the Wlan driver first.
    The wireless network card is recognized correctly in the Device Manager?
    Otherwise, install the WLan driver compatible; As much as I know the WLan card is Realtek RTL8191SE 802.11bgn

    Then once the Wlan card is recognized correctly, you must install the VAP (value added package) and Flash Cards support utility!
    These two tools are required to operate the FN keys and switch WLan using Fn + F8!

  • Satellite L655-149: recovery does not work with the new HARD drive

    Satellite L655-149

    PSK1JE

    Windows 7 Home Premium 64-bit (factory installed)

    Recovery of HARD drive on drive D (factory installed)

    My old toshiba (MK5065GSX) 500 GB hard drive became too noisy and slow so I plan to replace it with the new drive hard toshiba (MK5059GSXP) 500 GB.

    I created USB Flash HARD drive recovery.
    When the installation is complete and Setup installs devices an error "Windows Setup couldn't configure windows to run on a hardware on this computer.

    I've updated the bios
    I loaded by default in the bios
    I changed the SATA AHCI mode to compatibility IDLE

    assistance in this regard will be highly appreciated

    Set the BIOS to the default settings and try again.

    With the installation of recovery, there is a problem: either it works or not. If this isn't the case, bad luck and the only solution for you is to order original Toshiba recovery DVD on https://backupmedia.toshiba.eu/landing.aspx

    By the way: do you use that stick of recovery for the first time?

  • Satellite L30: CD player does not work with the new HARD drive

    Hello

    Just bought a new drive to HARD drive of 250 GB to transform my L30-115 has a home server.

    My problem is when both the new HARD disk drive DVD/CD-RW drive of origin are inserted into L30, the computer crashes and I can not even get into the BIOS (I have the latest edition).

    However, when I disconnect the CD player, system boots fine in a system of operating "plain" (command-line only) - BIOS recognizes very well and everything is fine. Idem: as I disconnect the HARD drive and connect the CD player, I am able to work (for example with a live linux system).

    The question is: * how to install a Windows operating system to a new HARD disk drive *? There is no option to boot from USB. What else can we do? I'm not going to invest more money into this old machine. I would like to install the Windows Home Server in there. There is no need to use the CD player later (all other operations will be performed by the network).

    Person not answering, so I'll do it.

    I was able to boot from USB external floppy drive, so the solution is to boot from external CD drive and install the system.

    It is not an exact solution, because the internal optical drive must be removed, so I'm looking forward to see updates to the BIOS level or other solutions for Toshiba.

  • C855 satellite - internet access Wireless does not work after upgrade to Win8

    Hello can someone help me?

    I have Toshiba Satellite C855 1HU. I just upgrade to Windows 8 and now I have no internet Wi - Fi.
    I don't see the wireless icon.
    I have downloaded the widipl - 20121025100952.zip it din't work.

    Means Enyone help me?

    Hello

    You laptop was equipped with card Realtek Wlan RTL8723AE
    I assume that you have installed the wrong driver Wlan.

    Check and try to install the Realtek Wlan driver released for the Win 7 system

  • Re: WIRELESS does not work after restoring the system to the factory settings

    Hello

    I just had to reset my Toshiba Windows 7 laptop to factory settings, I backed everything up to an external hardrive beforehand. After the process that kept restarting my laptop on its own, he did this, while the default Toshiba program was missing (from the application of the box). He said not to interrupt or turn off the PC while it was running, but I couldn't stop it do it several times. The process finally ends the green bar hit 39/39 and let me come back to the office.

    It seems to be OK now, but I can't get online, I have connected to my wireless router and it says connected with an excellent signal but I can't do anything on Internet Explorer. I would like to re - download a few things such as Adobe Flash Player, AVG Free, Mozilla Firefox but can't even get anything. It's not even an error message that appears when I'm on IE.

    Can someone help me please?

    Tommy

    I hope that you can use your laptop by using the LAN connection.
    Have you tried to reboot your router?

  • x 200 Wireless does not work after downgrading from Vista to XP - please advise

    Information system: x 200 74553YG / Windows Vista business product key

    Question: Used the recovery CD to downgrade from Vista to XP - downloaded all the drivers and updates to the operating system. everything worked except LAN wireless. Tried all possible ways to solve this problem (re download drivers)

    Your support and recommendation are highly appreciated

    so, there is no unknown device in the list? go into your bios and see if the wireless is turned on there or not.

  • Wireless does not work after Windows Update

    Original title: Wi - Fi internet connection is DISABLED since yesterdays upgrade, how can I get that back on?

    Since a windows update yesterday, before closing my laptop... I am not able to access the Internet.

    My without wire is off and I can't turn it back on.  Toshiba wants $99 for technical support.

    Hi Sheryl,

    Please join Microsoft Community where you can find the necessary information on Microsoft products!

    Wireless does not work after a windows update.

    1. what day that was installed?

    You can check the update in the update history:

    See the Windows updates are installed

    http://Windows.Microsoft.com/is-is/Windows7/see-which-Windows-updates-are-installed

    2. do you receive any error messages?

    3. What is the model of the computer?

    The problem may be with the drivers or with the device.

    I suggest that you refer to the procedure described in the site:

    Wireless and wired network problems

    http://Windows.Microsoft.com/en-us/Windows/network-connection-problem-help#network-problems=Windows-7&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

    I hope this helps. If the problem persists, let know us and we would be happy to help you.

  • Microphone does not work after upgrade from Vista Home Premium to Win 7 Home Basic-Sony Vaio VGN-NS25G

    Microphone does not work after upgrade from Vista Home Premium to win 7 Home Basic Edition. Laptop model Sony Vaio VGN-NS25G, bought in India

    My built-in mic not working anymore after the upgrade from Vista Home Premium to win 7 Home Basic Edition. Model laptop Sony Vaio VGN-NS25G was bought in India. I have taken the loacl Sony Service Center and they said that Windows 7 drivers for the microphone Sony was not yet available. They mentioned that the only way to fix the problem was to upgrade to Vista. Is this true? Where can I get these drivers for the microphone, and they are not available, when will they be available?

    Hello

    Method 1.
    Interestingly, I found the drivers for Windows 7 for this particular model of Vaio. Here is link thye:
    http://www.Sony-Asia.com/support/download/362654/product/VGN-ns25g/sectionfirst?subpage=detail

    I suggest updating all your drivers from the link above and drivers Realtek especially.

    Method 2. Set the default Microphone.

    Once the drivers installed to check if the microphone is the default value, here's how:

    Exercise the functions mentioned below to adjust the Microphone as default:
    1. Click Start and click on Control Panel.
    2. click on sound, then a new window will open.
    3. in the new windows, click on the 'Registration' tab and right click in the window and click Show disabled devices.
    4. now check if the Microphone is listed there and right-click on it and choose activate.
    5. turn highlighted that Microphone and click "set as default".
     
    For more information see the articles below:
    http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly
    http://Windows.Microsoft.com/en-us/Windows7/recording-audio-in-sound-recorder-frequently-asked-questions

    I hope this helps.

    Thank you, and in what concerns:
    Shekhar S - Microsoft technical support.

    Visit our Microsoft answers feedback Forum and let us know what you think.
    If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

  • Satellite Pro L40 Wireless does not and wont stop correctly

    Hello
    just got a Satellite Pro L40-15 1 week ago and it's been downhill.

    The Wireless does not work (and yes the switch is activated and drivers installed). Sometimes windows recognizes no device when I boot.

    And when I stopped he said blocking down, but crashes just on this screen.

    Now, I'm an advanced user, so I've tried many things. Can anyone help?

    Thank you

    As a first step, I would recommend to use the Toshiba Recovery CD and renew the operating system.
    Then update the Vista of the State. I mean to install patches and fixes Vista all published.

    Check this thread:
    http://forums.computers.Toshiba-Europe.com/forums//thread.jspa?MessageID=107665

    Here you can see that a missing patches can have a bad influence on the wireless network card and the entire operating system!

    Good luck

Maybe you are looking for

  • Tecra M2 starts only in safe mode

    I recently installed Norton products in my laptop Tecra M2, who met the necessary attention problems. However, when a Norton technician has resolved the problem, the laptop freezes and since my laptop was implemented in safe mode.Tried several option

  • EverWeb vs iWeb

    I build sites iWeb since January 2006 and EverWeb since February 2014. I'm not a model user page but create several sites of white pages. I'm not a coding expert but a user of the GUI. Please, add comments...

  • Count when whole Exchange?

    Hello Hope somone can help me with this. I have a position of analog speed sensor, which generates a voltage between 0 and 10 v according to the machine is chosen. (I'm simulating the input voltage to the VI attached using a digital command, and leve

  • (your current security setting does not allow this file to download)

    How to fix my security settings to not have the phrase your settings current security do not allow this file to download and stop from popping up whenever I want to download on the internet. I tried to change it to medium-high security also, failing,

  • Update IDSM2 5,0000 S225 to 5.1 using the application partition

    can I switch an IDSM2 (WS-SVC-IDSM2-BUN) in a 5,0000 S225 5.1 6513 by copying the partition of 5.1 application on the sensor [Correction to the userguide cisco] Chapter 10 Configuring the sensor using the CLI Modules and devices available Reimage on