Satellite Pro A10: Extraction failure error occurs during my recovery procedure

Similar Questions

• Satellite Pro A10 comes with: error IDE #0, PXE-E61media test failed

  I recently bought a used Toshiba Satellite pro A10.
  When I received it, it was working and being a noob I tried to install a network card and create a wireless network with my desktop using XP when it did not work I plugged my ethernet (from my desktop) cable on the laptop and flashed upwards with a small number can not? dll etc etc.

  Now I unplugged the ethernet cable and when I try to boot my laptop it comes up with:

  "ERROR IDE #0".
  Intel (r) bootagent, FE v4.1.09
  Copyright 1997-2002 Intel Corp.
  PXE - E61: Media test failed, check that the cables
  PXE - M0F: Exit Intel Boot Agent
  Insert system disk in drive
  Press any key ".

  HI Tom,

  The error message that you receive indicate that your laptop is trying to start the connection to the LAN rather than from his own hard drive or a CD-ROM. I suggest that you verify that the boot sequence is specified correctly in your BIOS, or alternatively, you can press F12 during your market and you should get the boot device menu sequence appears so that you can specify that you want to boot from your hard drive.

  Kind regards

• Satellite Pro A10 - IDE 1 # error at startup to the top

  HI, I have a Satellite pro A10 and everything is working very well in recent years to date.
  A few days ago I started having a cd read error / invalid dvd disc format still drives fine on all the other PCs work.

  Today as I get #1 error on boot up IDE... the laptop is always standard when I got off the shelf. thinking the drive might be dead due to wear I replaced the drive with a drive to work and I still get the same error. I removed the completely STRANGE and yet to come.

  I also updated the usb floppy bios that has been a success. and the best part of all this. the dvd - rom supplied with the laptop works fine in my other a10 tosh!

  Someone at - it ideas. I really need to replace the motherboard if I can help it. This is the only problem with the laptop.

  THX in advance people.

  Hello James

  IDE 1 # error is typical when ODD is not accepted by the system. The reason may be defective drive or the use of non-compliant readers. The fact is that each player can not be used with all portable models because of the allocation of the different pins.

  In your case, it is really strange that the work by car on other A10 but not on this one. Because of this, I presume that there may be a problem with connectors. I'm afraid there is not much to do. You can try to check out them and see if they are clean and not oxidized.

  Sorry, but we cannot speculate what may be the problem but, as you know, only intensive test may give you more answers.

  Good luck and let us know if you will find what is the problem of resources.

• Satellite Pro 4600: disk-read error occurs - press Ctrl Alt Del to restart

  I have a Pro 4600 which displays the error message "a disk read error has occurred. Press Ctrl Alt Del to restart "as soon as TOSHIBA logo goes.

  The laptop was given to me because the person who had tried to move to XP Pro and don't could not make it work, error with the CD Rom drive and she deleated the old OS (Win2000) off the coast.

  I took the hard drive and did a fresh install of XP by attaching the drive to another computer. The hard disk starts well on the other computer, but I get the error message on the Pro 4600.
  Any ideas. I know that I need to replace the CD Rom, but if I can't make it work, I don't want to drop money in it for a new CD Rom

  Thank you, Bob

  Hello

  Are you sure that the CD drive is dead?
  I have goggled a bit on the net and found some practical information that there may be some HDD malfunction.
  Some guys advised to use the command CHKDSK C: /R to solve this problem.

  But if it's a cd player error, it should be possible to disable the drive in Device Manager.

• Satellite Pro A10: IDE #1 error - drive doesn't appear unless the CD is inserted

  Hello

  I've been recently wearing on my bed watching a DVD when I fell asleep with the laptop sitting next me on my bed. During the night, however I moved and he accidentally knocked on the side of my bed.
  The next day when I booted up the loading it said IDE #1 error since then I understand it is a mistake to CD/DVD drive, the device works very well, starts ok (except the IDE error) and I can use it as usual except that there is no DVD drive in 'My computer', which is a bit of a pain when I want to watch a movie/play a game or install something.

  The drive itself is completely insensitive, when I press the button to eject the tray, it doesn't do a thing.
  I decided to try to remove and put back the drive to see if it was struck just loose when he fell of the bed as he fell only in short way (approximately down to 18 ".)

  I removed all the covers on the bottom of the laptop and checked that all was in place correctly and to try to understand how to remove the drive but would not do too adventurous as to worsen the situation, the only thing I have done is to remove the CPU fan and remove a few stuffed animals and remove the HARD drive and glanced to make sure it was not damaged in any place) It wasn't) and then replaced and replace all covers.

  When I rebooted the system, it started fine as usual, and the player react when I press the eject button, but the DVD player (sometimes) will now appear in 'My computer', but only when I insert something (be it a DVD/game/program), then it displays the error message an error of e/s on the device there.

  Any help of you all would be a great help, I thought just remove the drive and replacing it with a new one as a DVD RW one but I do not know how, I would be very grateful for advice and guidance you could provide.

  Thank you very much
  Michael

  Hi Michael,

  It is possible that the relocation of your optical drive may be necessary to refer it to the full. Unfortunately on the A10, it will be dismantled in order to achieve its screws located under the keyboard.

  Please see the following link for the complete disassembly instructions. The DVD player is covered in step 13. http://www.irisvista.com/tech/laptops/ToshibaA15/SatelliteA15_laptop_disassembly_1.htm

  concerning

• Windows vista error - catastrophic failure - error occurred during automatic backup of files

  • Windows vista service pack 2
  • error 0x8000FFFF catastrophic failure code
  • update browser GOOGLE chrome
  • Run the disk check, have also partioned disks (supplied with the new laptop), but still keep on this error

  SOLUTION:

  The solution to the problem, I met is the following:

  Step 1: RESTART your computer, press F8

  Step 2: select the first OPTION (depending on the manufacturer of your computer, it may be first or second, and so on...)

  The option is: fix my (the) computer

  Step 4: It will load the same in SafeMode (just an example), select your OWN USER NAME (though more are available), log in as an ADMINISTRATOR (if you are the one)

  Step 5: It will change into a small window asking you connect by using the command prompt: check this option (this may vary according to manufacturing, but it should be there)

  Step 6: Now when you log in you should see X:\Windows\System32 >

  Step 7: Change of disk C, D or E (essentially select your disk where the OS is installed)

  NOTE: If NO leave are present select your ONE and ONLY by CAR.

  If left are, for example: D and E (D contains BONES, E contains - your stuff)

  Select drive with OS, i.e. D drive

  Step 8: After your decision to step 7, it would look like

  X:\Windows\System32\C:

  Step 9: The result would now be C:\ >

  SO BASICALLY WE ARE ACCESSING THE HDD FROM OUTSIDE

  Step 10: Type Chkdsk/r/f

  Step 11: wait for the results

  The first 3 steps will be complete as soon as POSSIBLE, the 4th and 5th stage will TAKE ABOUT 120 minutes (variable, based on the hard drive, the computer specifications and especially your processor)

  The result should tell you more about the DEFECTIVE AREAS, indexing ERRORS and similar stuff, and also they could be repaired.

  When finished: TUPE OUTPUT

  At the end of OUTPUT

  and REBOOT

  step 12: now even ONCE, go to the BACK UP CENTER, launch a NEW BACK UP, it should work :)

  NOTE: I appreciate the incredible help with MICROSOFT research, engineers who were very thoughtful and dedicated to get my problem sorted out and help out me.

  All these steps are suggestions for these engineers, NOT MY JOB: p

  KUDOS TO MICROSOFT AND HIS TEAM!

  See you soon,.

  Jay

  BTW: these guys who gave METHODS of TRIALS AND ERRORS, thanks to you also, I learned a lot.

• IDE #1 error on Satellite Pro A10

  Hi, my laptop Satellite Pro A10 displays IDE #1 error whenever I try to put it on. This message is all I get, even if it is shown for a short period of time - the laptop always comes back to this message, it tries to load blanbk of the screen just go and then this message appears every time! I was wondering if someone could explain what this means and how can I solve this problem?

  Thank you

  David

  Hello David

  This error occurs if there is a problem with the CD/DVD drive. For example, this error occurs if you try to use the incompatible reader. It will be interesting to see what happens if the drive is removed.

  You did any player upgrade?

• Satellite Pro A10 stops during the installation of Windows

  I have a satellite Pro A10, which stops during the installation of Windows. The installation gets to the part where I need to select the HARD drive to install, then the system off just. I can restart it immediately, and the sdame happens.

  If I enter the BIOS, everything is detected OK, and I've updated to the latest version (V1.4). Also when in the BIOS, the system will remain under tension for ever and a day! and no downtime. I have a couple of diagnostic CD, then run the tests is the same thing, but I ran the seagate diagnostic tool and the HDD OK passes, as does the main map, but cannot perform detailed testing that the system shuts down during the tests.

  I suspect an overheating issue but would like advice.

  Hmmm it s very strange. I thought that the HARD drive could malfunctions but it of very impossible if the HARD drive has passed the Seagate diagnostic test.

  However, it would be very interesting to know if the installation of the OS would end with another HARD drive.
  You know, it of always difficult to provide an exact solution without any diagnostic tests.

  For me, it really looks like a hardware malfunction. So perhaps it would be advisable to contact the authorized Toshiba maintainer for a control of the laptop.
  Guys could run tests and would situate the fault quickly.

• Satellite Pro A10 - no answer - enter HDD #0 error

  Pro warranty A10, student daughter portable computer reports no longer works, already suspended and finally no response from any other lights at the entrance to DC charger is connected.

  Clean fan/radiator, a lot of lint etc. removed. No obvious signs to know why the Board me dead however. Confirmed with counters that this DC of the shipper in me Board. Ordered A replacement me Board, FHZSY1, eBay and equipped, taking the precautions of static, but can not confirm that they were done by the seller.
  Now, new Board of Directors recognizes the input DC and recharged the battery OK. Tried to turn on the laptop but terrible mistake INPUT #0. Concluded that the HARD drive had also been damaged. New (Toshiba box) arrived two days later but gave the same error when mounted. BIOS won't recognize HARD at all. Tried all the messages on the verification of the connections and certainly not of mounted riders. Laptop will continue to start from a system CD, as it may then think the new me Board is OK

  Are the HARD drive of the Satellite Pro A10 different from those on the A10 satellite earlier?
  Any other ideas on this INPUT #0 error?
  Thank you

  Hello

  As much as I know there is no different hard disks and your use of the same laptop as most other Toshiba laptops. I can just write that this error is certainly resulting HARD disk problem. The HARD drive is obviously not identified by BIOS correctly.

  Sorry but I have no more info on this subject. By the way: is the motherboard new or used one?

• SD-C2612 IDE #1 error after wrong firmware update - Satellite Pro A10

  Hello
  I have a Toshiba Satellite Pro A10, which was flashed with wrong firmware (I don't know which because I don't).

  I tried flashing with the right firmware (1315) but get the message to the Primary Master and Slave as "Not ATAPI Device" and "drive not connected".

  NB: at the start, even with the deleted DVD ROM, I always get the #1 error IDE.

  Update the bios to the latest version would help or is there all the options open for me to solve this problem other than to have recourse to the connection of pin 47 & 45? Would it even solves?

  Thanks in advance for any advice you can give.

  Best regards
  Angus

  > I have a Toshiba Satellite Pro A10, which was flashed with wrong firmware (I don't know which because I don't).

  Lol :D I have don t wonder you get the IDE #1 error message.
  As you say yourself, you have flashed the drive with the wrong firmware. This has damaged the master/slave/c-salt settings of readers and so the BIOS doesn't recognize the CD/DVD drive. But I wonder why someone flashing the drive with a bad firmware?  :| We still know that a wrong firmware can damage the CD/DVD drive... and above all it is not necessary to update the firmware.

  > Update the bios to the latest version would help
  The BISO update will not help you because you have already good BIOS and it s NOT a problem of BIOS, but the evil and not compatible firmware is stored.

  > or are there options open for me to solve this problem other than to have recourse to the connection of pin 47 & 45? Would it even solves?
  I'm don't know if this helps, but I know that it is not desirable because it may damage the material of CD/DVD players

  I recommend you contact the ASP in your country guys might revive the CD/DVD drive. Let's hope

• Hello! I work with the Director 12, Windows 7. A fatal error occurred during my attempt to chance the script police. Now this fatal error occurred whenever I start the Director. I shut down the system and tried again, even failure. What can I do?

  Hello!

  I work with the Director 12, Windows 7. A fatal error occurred during my attempt to chance the script police. Now this fatal error occurred whenever I start the Director. I shut down the system and tried again, even failure.

  What can I do?

  Save the relevant keys, then search your registry at HKCU\Software\Adobe\Director\12\Script

  If this does not help, save the entire branch and try to delete it

• I do P2V of a Linux Machine, his failure with the error "FAILED: an error occurred during conversion:"root is not found""If anyone can suggest how to solve this. "

  I do P2V of a Linux Machine, his failure with the error "FAILED: an error occurred during conversion:"root is not found""If anyone can suggest how to solve this...» He does not drive partition root to copy don't know why his account right there.

  I solved the problem myself... This is because the Version of Vcenter Converter. I'm using Vcenter Converter 5 to P2V a server Linux RHEL5.2, its not supported by Vcenter Converter 5. That of why I've done P2V using Vcenter Converter5.2 and accomplished.

• An error occurred during the opening of the first CC Pro 2014: first a debug event

  An error occurred during the opening of the first CC Pro 2014: first a debug event

  [c:------cloudroom------frees------2014.9------shared-adobe-mediacore-mediafoundation\API\in]

  I don't know what to do, any help?

  

  Remove effects and Items.prfpset, located in custom presets

  C:\Users\\Documents\Adobe\Premiere Pro\8.0\Profile-

  When succesfull make new project and import an old into new.

  Need to maybe reset the current workspace and pull down of the audiotracks first to reveal videotracks.

• Satellite Pro A10 HDD

  I have the Satellite Pro A10 C2.2GHz/XP Home/256 MB/20 GB/14TFT/DVD/WiFi. One day, the computer just froze and then resets and would not start again, and I kept getting the message:

  «PXE - E61: MEDIA TEST FAILURE, CHECK CABLE.» PXE - M0F: EXIT INTEL BOOT AGENT. "INSERT SYSTEM DISK IN.

  or

  'A DISK READ ERROR OCCURRED '.

  I tried some hard disk controllers, but they are unable to get anywhere, because they cannot access the drive. Anyone know of any solution to this, or if not, where would be the best place for replacement because my warranty has run out.

  Any help appreciated,

  Thank you
  Tom

  Hi John,.

  Unfortunately, it seems that if your HARD drive has crashed. The message of your BIOS is normally what you see if the PC cannot detect any bootable devices. Usually, it is a bootable HARD drive.

  Assuming you have the Toshiba Recovery CD you could try to restore your existing system to your HDD (it will automatically reformat the hard disk first), but you might find although it will simply fail restore due to the failure of the drive.

  Your next option is to replace the HARD drive. You can do it yourself very easily, or you may prefer to take the laptop to a Service Agent for them to do. Note that you still need to rebuild your system from the recovery CD according to your choice.

  Given that your device has a 20 GB HARD drive standard you could take this opportunity to install a larger capacity drive.

  HTH

• Satellite Pro A10 display and DVD issues

  I have a Satellite Pro A10 about 2 1/2 years and have never had a problem with him, but the other day when I tried to watch a DVD, look at a program (InterActual Player) opened as usual and then a few more seconds later the display will change in very low resolution (something like 14 colors, almost a negative and all image was massive Although I don't remember the actual numbers) and he said that I had to reboot in order to return things to normal. I tried the same DVD in Windows Media Player, as well as to try other DVDs and initially that the DVD would play in Media Player but not Interactual but now the same thing happens any DVD or player that I use.

  Also, I went on the computer this morning and got a message saying that the battery is low (although it was because I had not plugged the computer again, nothing to do with the last errors) and the computer is in standby. I plugged in the computer and you press the power button to wake the screen is very dark but visibly pixelated (I think that's the word, he had visible points, as if someone were holding a magnifying glass up to her) and got very slowly brighter until there has been a series of narrow bright stripes, like a giant pixel or a tv test screen.
  This could be a problem with the display drivers (even though I tried to update and we found since I always see a message 'Cannot find the requested string' by the icon for display in the control panel), the screen itself, or something else entirely?

  Sorry it's so long, but I thought it is best to include all the details in case it has been important. I hope someone can help!

  Hello Nicola

  As you know on this path is not easy to say what may be the problem. In my opinion, it is important to see what is happening exactly. I assume that your problem is not caused by the display driver. Try to properly test and notice where the screen is very dark.

  If this problem is repeated again and again that I recommend you backup your data and reinstall the unit with recovery media. On this path of unity will be factory configured and you can see if the problem still occurs. If so, it may be just caused by a malfunction of the equipment.

  Good luck!