Satellite Pro A110 crashes during the transfer of the large data in LAN

Similar Questions

• Satellite Pro L100 - Crash during the update of the Bios

  Hello

  I am the owner of a Satellite Pro L100 (PSLA4E)

  On the Toshiba site I downloaded the BIOS update. While installing I read that it was necessary to supply cable is plugged. Before I could cancel for the cable, he had started and then frozen. The computer stopped working and so I turned it off! Since then, I've read that it was a very big mistake!

  When put on the fan starts and I can hear etc cd drive spinning. After 15 seconds, the screen is blank, the computer starts beeping!
  Is there a way to solve this?

  Thank you very much
  Rich

  Hi Richard

  Seems not good buddy from your description, that something went wrong during the update procedure and now the ROM module has been flashed properly.

  Maybe you area lucky man and the motherboard isn't too bad, but only the Rom module must be flashed again.

  Unfortunately, this must be done by the technician of the ASP. You will need to contact the ASP in your country for assistance.

  Good luck and have a nice day

• Satellite Pro A60 crashed during the update of the BIOS

  Updating to BIOS ver 1.70 to 1.90 (from Windows XP) my Satellite Pro A60 off without any warnings. After about 5 minutes of waiting I went it. And... computer just several beeps and stops again.
  Anyone has idea what it means? Is it possible to turn it on again?

  Hi Vladimir,.

  I suspect that your BIOS is damaged when your A60 turns off. Unfortunately, this means you A60 are a failure now his POSITION leading to generate failure codes series.

  As Felix said codes tells the Toshiba Service Agent exactly what the problem is so you will need to contact them for assistance.

  HTH

• Satellite Pro A100 crashed during Windows BIOS upgrade, now does not start.

  Satellite Pro A100 crashed during the upgrade of the bios from windows (upgrade the bios using windows), now the laptop will not boot. I press the on switch and it gives me just a blank screen, so I think that resets itself. I really need help solving this because I have a University paper due in the next few days and I need my laptop!
  Close for any help.

  It's a scream! :_| : O

  This looks like a damage ROM module!
  How did you do the BIOS update? I have red in this forum that a wrong procedure or wrong BIOS can damage the motherboard.

  I think that it s a deal. I put t know if it s needed to change the entire motherboard or update the BIOS again but I n t think you will be able to do it yourself.

  I think the best way is to ask the Toshiba service partner in your country.
  I think they'll give you more details on the handling of the Fryer

• Satellite Pro A10 stops during the installation of Windows

  I have a satellite Pro A10, which stops during the installation of Windows. The installation gets to the part where I need to select the HARD drive to install, then the system off just. I can restart it immediately, and the sdame happens.

  If I enter the BIOS, everything is detected OK, and I've updated to the latest version (V1.4). Also when in the BIOS, the system will remain under tension for ever and a day! and no downtime. I have a couple of diagnostic CD, then run the tests is the same thing, but I ran the seagate diagnostic tool and the HDD OK passes, as does the main map, but cannot perform detailed testing that the system shuts down during the tests.

  I suspect an overheating issue but would like advice.

  Hmmm it s very strange. I thought that the HARD drive could malfunctions but it of very impossible if the HARD drive has passed the Seagate diagnostic test.

  However, it would be very interesting to know if the installation of the OS would end with another HARD drive.
  You know, it of always difficult to provide an exact solution without any diagnostic tests.

  For me, it really looks like a hardware malfunction. So perhaps it would be advisable to contact the authorized Toshiba maintainer for a control of the laptop.
  Guys could run tests and would situate the fault quickly.

• Satellite A210-15Y crashed during the update of the bios

  The worst case has happened and the laptop computer crashed during an update of the bios. I know that there is the possibility to repait the bios with a tool of recovery from crisis. For this purpose you have to press 2 keys (in most cases FN + B or Win + B) during the connection of the supply cable and the next start. I tried many books, but nothing happened. Can someone tell me the keys on which I have to press a 210 - 15Y satellite and maybe where I can get an image of cd of the tool of the crisis, because the laptop does not have a floppydrive?

  Hello

  As far as I know that the BIOS crisis procedure may be crazy by a technician of the ASP.
  You can not download a version of traditional BIOS who can update the BIOS from a USB FDD floppy.
  You can download only focused on the victory of the BIOS that can be run so that windows operating system is running.

  In my opinion, you should get in touch with a local ASP!

• Satellite Pro A10 hangs during the installation of Win XP

  Hi guys,.

  just thouth I would ask why my new laptop will not install XP.
  Only, it crashes during installation. No n' achete purchased on this occasion, had no operating system installed.

  I wonder if it's a driver problem, using my xp disc I bought, but like I said that just, it will hang during installation.
  What I need to intergrate drivers somehow?
  I'm guessing that this is the problem?

  If so, how do I?

  see you soon

  I really wonder that your new laptop is probably produced about 5 years ago. ;)

  In any case, to install WXP use WindowsXP SP1 installations CD (factory settings). If you want to discuss a little more please explain to us what exactly is happening.

• All new Satellite Pro L300D crashes all the time

  Hello

  I'm a little base when it comes to laptops.
  I just bought this new L300D to ebuyer

  I started and I have an anti-virus etc. But without apparent reason, the computer crashes.
  The only way out is pressed the switch out. Everything is frozen.

  It will do about 2 times and then after restarting it seems to work ok.

  I got windows to its original by HARD drive recovery settings and it did make a difference.
  I am as I say not a computer wizz.

  Can someone tell me how I can stop it crashing, it's really annoying.

  Kind regards
  Michelle

  Hello

  Does this happen often?
  I mean that the Windows operating system could break sometimes without any serious reason, sometimes a software compatibility issue might be the reason why the OS freezes.

  But I have this problem would fall so I recommend you contact an ASP in your country. It could be related to defective material

  Your laptop is under warranty (we hope) then the warranty should cover all hardware issues

• Windows 8 crashed during the last update, now wants to save and may not do.

  Windows 8 crashed during the last update. Stuck at 30% for more than 4 hours before I finally pressed the power button to restart the system. Windows 8 Pro with Media Center now says system build 9200 at the bottom right of the screen.

  Whenever I try to activate Windows 8, it cannot connect. When you use the command prompt Windows + R and slui 3 with my purchased serial number I get Code 0 x 80070424. Description: The specified service does not exist as an installed service.

  Hello

  This error can appear if your firewall settings prevent Windows to complete the online activation process. To resolve this problem, you can activate Windows by phone instead.

  1. Enter in the right edge of the screen and then click on Search.
     (If you use a mouse, point to the upper right of the screen, move the pointer of the mouse down and then click find.)
  2. Type SLUI 04 in the search box, type or click on applicationsand then tap or click SLUI 04.
  3. Follow the instructions on the screen.

  Hope this helps

• Satellite Pro L500 - stops when the power cord removed

  Toshiba Satellite Pro L500 stops when the power cord is removed even with the battery to 100%. I removed the battery and all the indications associated with battery answer correctly. For example turns off, Toshiba Health Monitor also indicates when the battery is removed. If installed Health monitor indicates that the battery is at 100%.

  Someone please help. I have not installed anything new.

  Hey,.

  For me, the matter is clear: the battery can't hold a charge so the laptop will be shut down because it has no power.

  I think you need to replace the battery with a new one and you can get a provider of service authorized in your country. Simply contact the guy and ask that they can tell you how much it would cost.

  You can find a list of all FSA here:
  http://EU.computers.Toshiba-Europe.com > support & downloads > find an authorized service provider

  Good luck! :)

• Equium A60 crashed during the update of the Bios

  Hello, can someone tell me if this can be repaired. IHAVE an A60 Equium that crashed during the update of the BIOS, now he died nothing lights up.
  Thanks in advance

  I presume that the BIOS chip is damaged. In this case, you can do anything to make it work again. Just approved can help.

  The problem is that the repair can be quite expensive. Check it out. If selling Yes the laptop on eBay and... you know what I mean. :(

• I don't like to upgrade Windows XP to Windows 7, because I'm blue screen/crash during the upgrade but the upgrade Windows XP to Windows Vista does not crash during the upgrade!

  I have my computer to another, here my specs:

  Intel Core 2 Duo
  Hard drive 500 GB
  2 GB OF RAM
  DVD player
  Floppy Disk
  The operating system that is running Genuine Windows XP Professional Service Pack 3 and just upgraded Windows 7 (but I know before upgrading Windows 7) and keep the blue screen / Crash when upgrading to Windows 7. but the upgrade Windows XP to Windows Vista is not blue screen/crash during the upgrade.
  Is anyone to upgrade from earlier version of Windows to Windows 7 without crashing and spending fortune?

  Hello

  1 did you change on your computer before this problem?

  2. What is the blue stop screen error message?

  3. When you receive a blue screen during the upgrade?

  You can follow the suggestions and then check.

  Method 1

  Disconnect external devices connected to the computer?

  Method 2

  You can read the article and then check.

  Upgrade Windows XP to Windows 7

  http://Windows.Microsoft.com/en-us/Windows7/help/upgrading-from-Windows-XP-to-Windows-7

  See also:

  Windows 7 Upgrade and Migration Guide

  http://TechNet.Microsoft.com/en-us/library/dd446674 (v = ws.10) .aspx

• My mac crashes during the installation of the cs6. I have to turn off the mac. Now, I can't reinstall or uninstall cs6. He said the Installer failed to initialize.

  My mac crashes during the installation of the cs6. I have to turn off the mac. Now, I can't reinstall or uninstall cs6. He said the Installer failed to initialize.

  If you have not yet installed any Adobe application, try step below and check.

  Step 1

  (1) right-click on the icon in the Finder, then select 'Go - To' folder.
  (2) you will get a text box, type in the following command and then press the 'return '. ( "Don't miss ~ symbol" )

  ~/Library

  It will open the folder of the user's library.

  (3) then navigate to Application Support > Adobe.

  Open the Adobe folder and rename the OOBE, OOBE old and AAMUpdater to old AAMUpdater.

  Step 2

  (1) right-click on the icon in the Finder, then select 'Go - To' folder.
  (2) you will get a text box, type in the following command and then press the 'return '.

  / Library

  It will open the folder System Library.

  (3) then navigate to Application Support > Adobe.

  Open the Adobe folder and rename the folder Caps Caps-old and young OOBE to centenarians, OOBE Adobe Application Manager of Adobe Application Manager.
  

  
  

  Step 3)

  Basket of Adobe Application Manager of Applications > utilities.

  Step 4) [same step again]
  

  Click on the link below and download Adobe Application Manager and install the same:

  http://download.Adobe.com/pub/Adobe/creativesuite/CC/Mac/ApplicationManager9.0_all.dmg

  Once installation is complete, niche is going disappear, and then open the Application folder and locate the icon to launch Adobe Application manager, double-click it and update.

  Once the update is complete.

  Restart the computer once and try to install CS 6.

• How to install the large data file?

  Anyone know how I can install large binary data to BlackBerry files during the installation of an application?

  My application needs a size of 8 MB of the data file.

  I tried to add the file in my BlackBerry project in the Eclipse environment.

  But the compiler could not generate an executable file with the following message.

  «Unrecoverable internal error: java.lang.NullPointerException.» CAP run for the project xxxx»

  So, I tested with a small binary file. This time, the compiler generated a cod file. but the javaloader to load the application with this message.

  "Error: file is not a valid Java code file.

  When I tried with a small plus, we managed to load, but I failed to run the program with that.

  "Error at startup xxx: Module 'xxx' has verification error at offset 42b 5 (codfile version 78) 3135.

  Is it possible to include large binary data files in the cod file?

  And what is the best practice to deal with such a large data files?

  I hope to get a useful answer to my question.

  Thanks in advance for your answer.

  Kim.

  I finally managed to include the large data file in library projects.

  I have divided the data file in 2 separate files and then each file added to library projects.

  Each project the library has about 4 MB of the data file.

  So I have to install 3 .cod files.

  But in any case, it works fine. And I think that there will not be any problem because I use library projects only the first time.

  Peter, thank you very much for your support...

  Kim

• Satellite Pro A110 - in BIOS exclamation Point in front of the HARD drive

  Satellite A110 Pro PSAB1C-GM80XE

  Question is this. SATA CONTROLLER TOAST the laptop?

  Story.

  It seems as if the laptop hard drive has failed.
  Prior to the laptop, it would get BSOD.
  It would, however, go back to windows XP.

  After that, sometimes it wouldn't restart, he would try to boot from lan as if there is no hard drives.
  I check the bios.

  There is a! in front of the model of the drive. I can't change it, reset default does not change.
  No update of the bios was already made.
  Page drivers laptop says I have to install the update to the bios from windows xp... I can't do it of course.

  I bought a new hard drive for the laptop. WD Scorpio Blue (pretty standard) 160Gig

  The laptop recognize model to drive hard in the bios, but once again with the exclamation point in front of the name of the template.

  BIOS can see, but nothing else. No windows CD is able to watch the HD.

  Once again, it is the sata controller or can someone point me to an update of the bios I can do with a USB key.
  Should I just throw the laptop in the trash? I expect to give it a new life with a new hard drive and own bones.

  Hello

  What is the BSOD STOP Code?

  If 0x0000007B, it means that Windows cannot find a SATA driver for the SATA controller. To solve this BSOD, set the SATA Mode in the BIOS in "COMPATIBILITY" mode, or use a USB floppy with the SATA driver on this subject during the installation of Windows. Press F6 when you are prompted to install a 3rd party storage driver.

  Or otherwise, to use the original Toshiba Recovery disk to install Windows.

  I do not mean the exclamation point in the BIOS that the HARD drive is faulty, it means that the HARD drive has the highest priority boot on my laptop.