Satellite Pro A120 driver install

Similar Questions

• Satellite Pro A120 - cannot install recovery disc

  Hi - I have a Toshiba Satellite Pro A120 PSAC1E-04H00VEN model number

  It was less his hard drive and I posted previously to try a 160 GB drive without success. I thought that the drive may be defective, so I have now acquired a 120 GB drive. It is not new, but assured me that it works. However, it does not work in this laptop! As before (with the disk 160), when I try to install it using the Toshiba restore disc, the operation just sticks on the "Please wait..." message. "for 30 minutes then the machine shuts down. Assuming that the hard drive is ok there at - it something more, that I can do to determine the problem with this laptop?

  FYI, this is what happens after installing the hard drive:
  I turn it on and get this message: NTLDR is missing. Press Ctrl + Alt + Delete to restart.
  I insert the product recovery disc, put off and then again when you press F12.
  I get a soft Purring over the Toshiba logo. I select the CD/DVD symbol and get a short message saying: the installer inspects the hardware configuration of your computer.
  I then get RAMDISK image loading... which takes less than 2 minutes.
  I then get a short message saying: from Windows Preinstallation Environment. Press F6 if you need to install a third-party RAID or SCSI driver...
  I then get it please wait... and after 10 seconds, the fan goes into overdrive! This Carry on during 30 minutes with him please wait... message, then the laptop turns off automatically.

  Any ideas anyone?

  Thank you.

  Hi Lapitup,

  Before you buy another HARD drive, you need to test a different installation disk you have already tried the two hard disks with the same problem so I think that the problem is not HARD drive itself

  If you have a normal installation disc of Windows, you can install Windows on this drive. So you can check if the recovery disk works properly or not. Theoretically, the disc could be wiped off so that the files cannot be read properly.

  In the worst cases, some of the material is affected. Then, you need professional help of an authorized service provider.

• Satellite Pro A120 - cannot access BIOS and install Win XP

  Hello

  I ve a Toshiba Satellite Pro A120, I installed an operating system Linux on ve and uninstalled.

  When I go back to the Windows XP operating system, I just couldn't access the Bios (event the i press F1, F2) and the computer cannot start the windows XP SP2 CD too but it starts windows XP 2001 CD

  Could someone help me please

  Hello

  To access the BIOS, you can try press ESC then F1.
  Pro A120 was equipped with the Toshiba BIOS and that is why the ESC and F1 should functions.

  To boot from the CD of Win XP you can also press F12 immediately after switching on the laptop. This will start on the screen menu and there you can choose the CD/DVD drive as the boot source!

  Welcome them

• Satellite Pro A120 - Jerky empty reading after installing new HARD drive

  Just installed a new hard drive in my Satellite Pro A120. Made a full new install Vista, installed all the drivers but video playback is choppy/jerky. Even google earth is juddery. It didn't use to be like this with the original hard drive.

  A I had a problem of driver somewhere? I think it's the 945 chipset.

  Hey Buddy,

  To be honest, it's really hard for us, users, to say what causes this problem and I think you should test more yourself

  Anyway, you have reinstalled Windows using the Toshiba Recovery disk?
  You should also check if all Windows updates are installed and if you have yellow exclamation points in Device Manager.
  For any use of video and multimedia substance High Performance plan wrote BobRock_1.

  Sorry, but I think that it s all we can say :(

• Question about installing WXP LAN Driver on Satellite Pro A120

  I have a Satellite Pro A120 (PSACIE) with Vista installed. I created a dual boot with XP Prof I seem to have all the drivers except the WLAN and LAN drivers. I have downloaded the LAN driver there is no setup.exe file. No problem, (I think, maybe someone out there knows differently?).

  I used Device Manager to load the file inf and intel pro/1000 PL network connection selected with the Hardware Installation Wizard. At the end the wizard said there was an error code 10 and that the device probably would not work properly.

  Can anyone help? It does not of course! By pure chance that I bought a port replicator, its LAN works with XP but do not work with Vista! (There is a hint here)

  Is it possible I can get details on the LAN device such as model, serial number? Any help appreciated gratefully.

  Hello

  Are you sure you used a right and support for driver LAN?
  Error code 10 is known to me and mostly it appears if the device cannot be started because the driver is not compatible

  Ok. To my knowledge, there are two different Satellite Pro A120:
  the unit of PSAC0E supports Lan Chip Realtek 8100 CL

  and the PSAC1E supports the chip Intel 82573 L (Vidalia)

  So, what phone do you use?

• How to install the driver LAN for Satellite Pro A120

  In fact, my problem is that I didn't know how to install the driver on my Satellite Pro A120 lan connect net throug.
  The issue that there's no facility to do to complete the installation.

  And theres other question that I need the Ethernet controller

  My laptop was vista operating system installed, but I change and put Windows XP

  Please help me

  Hello

  LAN installation is very easy.
  First of all, you need the correct LAN driver.
  In order to download the LAN driver please visit the Toshiba driver page and choose your model of laptop.

  Once the LAN driver has been downloaded, you will need to decompress.
  Then you will need to access the Device Manager, choose the controller Ethernet (network cards) and must point to the place where the LAN driver was decompressed.

  Then finish the installation procedure.

• Cannot install driver Intel 7.14.10.1227 on Satellite Pro A120

  Hello

  I have a problem with the upgrade of my Satellite Pro A120 PSAC1 - 10l with Windows Vista Professional on this topic. I want to install the display driver Intels 7.14.10.1227 I downloaded the Toshibas site. It was written that this driver is my gm945 chipset.

  When I try to lunch the installation it says that: my computer does not respond with the minimum req for the installation of the software. Even in the Readme file, it is said that it is for my computer. Help me with this!

  Thank you
  Paul

  You are right. The Satellite Pro A120 PSAC1E seems to be equipped with the Intel 945 GM Express Chipset graphics card chipsets.

  I checked the page of the Toshiba driver and found another; Intel 7.14.10.1147 driver version.

  Please check if this version can be installed correctly on your system.

• Satellite Pro A120 - Maximum capacity of the HARD drive?

  HI - new here. I have a:

  Toshiba Satellite Pro A120
  Model PSAC1E-04H00VEN number

  It's less hard drive. I have a 160 GB spare hard drive but when I try to install this using the recovery disc, the operation simply sticks on the "Please wait..." message. ». The specification for the A120, I noted that it supports drives of 40 to 120 GB. Which is strictly true and so why can't I just install this 160 GB drive?

  Thank you.

  Hi Lapitup,

  Usually the 160 GB should be no problem because the laptop supports the SATA interface and there is no limit of ability so that you can install each HARD drive.

  Be interesting to know what HARD drive you have installed exactly and if you tested on another computer because the HARD drive itself could be the problem and not on the computer. If the disc is defective recovery disc can t be installed so that you get an error message.

• Satellite Pro A120-10W - function keys not working not not from the cloth of hard drive

  Hello

  I have a Satellite Pro A120-10W under Windows XP Pro SP3, and just had my hard drive erased, because of virus. Everything seems to work fine, but I can't use function keys to change the brightness etc. I looked in various forums help however most seem to give answers for Windows 7 or vista. 7
  Can someone please?

  Thanks in advance.

  Hello

  As you can see in other threads, you need special drivers/tools for the keys FN get their work because there is no standard Windows driver for these keys.

  In any case, you must download the common Modules like Akuma wrote. After installing the key should start working again.
  You can download the tools on the official website of Toshiba.

  If you have problems with the installation or it succeeded, just after a few comments. ;)

• Satellite Pro A120: I have problems with the installation of the graphics driver for W2k

  I installed windows 2000 on an A120, the system is fully packed and service updated before I even start to install the necessary drivers, I am unable to restart the system. I once, install as recommended drivers that I have problems with the graphics driver because it will not be installed because it requires a reboot and then I can't install new programs that require a restart that the driver has not been installed correctly.

  The laptop is a Pro A120, age of 1 week and came with XP home, because of this toshiba will not offer me support I changed the o/s even though they obviously support 2000 on this laptop, because they provide the drivers.

  Any ideas would be greatly appreciated.

  Hello

  Did you use and install the drivers from the Toshiba driver page right?
  The drivers of Toshiba W2k for Satellite Pro A120 have been published and are ready!

  But please pay attention to the Toshiba drivers.
  There are two different sets of Satellite Pro A120, with different drivers W2k!
  After choosing the good laptop and download the drivers please follow the proper installation order that is indicated in the document "installation instructions"! Check it!

  I think that if you follow this guide line everything works and runs correctly. Good luck

• Need device driver IrDA for XP for Satellite Pro A120 PSAC1E

  I install win XP sp II in a Satellite Pro A120 PSAC1E.
  I find all the drivers except Irda driver.
  How can I get?

  Thank you

  Are you 100% that this laptop supports an IrDA port?

  By the way; all laptops with an IrDA port use a common Microsoft Windows driver to run the IrDA port.
  Then you n don't need to install any 3rd irda drivers. The windows OS using a clean!

  But once again; the question is: is this laptop supports IrDA port? I think that this feuture is not available

• Not able to install the common module on satellite Pro A120

  Hi guys:
  I recently reinstalled xp professional on my satellite pro A120. I could download and install the main drivers of http://uk.computers.toshiba-europe.com and my phone is functional. However, I did not all sounds and (F6 & F7 and toggle) function keys not working, even after insalling the sound card. I read some of the posts on this forum and found that I needed insall the 'common' module to make them functional. I downloaded the driver from module common too, but when I run the Setup it starts initially, but fails both the configuration is complete.

  The same thing happens also with a few other drivers as saver of energy etc... I was not able to run the Setup program for the common module & driver power saver, basically, nothing happens after I have the respective installation.

  Can anyone help please?

  Pravesh

  As far as I know on the download page you can find the installation instructions with exact installation document order how to install drivers and tools specific to Toshiba and utilities.
  You have installed all the stuff after this installation order?

• Satellite Pro A120 - cannot boot from CD/DVD drive

  I have a Toshiba Satellite Pro A120 of friends, he was running very slow so I said I'd do the usual for him.
  Back up all his documents, and then reinstall windows. not so easy!

  First of all, try to boot from the CD so I can boot into Ubuntu or reinstall windows.
  Me has taken long enough to work, I had to press DEL/ESC to enter in the BIOS, but once I put to boot from the CD (and was a bootable CD in the drive), it kept just boot from the HARD drive.

  From time to time I get an error saying + "Media test failure - check cable" + or something similar, theres a lot on internet on this subject.
  I think its something to do if the boot order has CD first, then it has LAN as 2nd.

  Able to boot Ubuntu from a USB key.
  Try to copy its documents on my external drive but really copying REALLY slow (like 1 MB/s) and kept getting IO errors on some files.
  I can't run diagnostic software for HARD drive that I can not boot from the CD (could get the Ultimate Boot CD on a USB but if anyone thinks it would help?).

  In windows, the CD player only reads real CD (audio similar DVD, not CDR and DVDR).
  This means a failing drive?
  What intrigues me most, however, is that I changed the portable CD player with a CD of work of another computer and windows recognize today this new CD player at all!

  By putting a bootable CD in this new CD player, it always starts from the HARD drive (do not recognize CD player in all).
  The BIOS is a bit unnecessary and does not show the detected disks...

  Also, boot Ubuntu from a USB key, with the original CD player, he reads real CD and DVD copied of all zeros are considered blank discs and replace the CD drive with a known working in Ubuntu means its not recognized at all (if this isn't windows driver problems).

  When I started messing around with it I remember windows say the time had been reset, so I set the time properly, then he did the same thing again I think. A flat CMOS battery could not be responsible for this?

  Is the motherboard and specifically the IDE controller or a broken ports, or am I doing something stupid? I'm tempted to just install Ubuntu by USB and tell him not to bother with CD more ;^)

  Any suggestions or comments would be much appreciated!

  Thank you
  Dan Gent

  > Me has taken long enough to work, I had to press DEL/ESC to enter in the BIOS, but once I put to boot from the CD (and was a bootable CD in the drive), it kept just boot from the HARD drive.
  You see the CD/DVD drive in BIOS? I mean all the details like the name WEIRD etc.
  If this isn't the case, then it means that your CD/DVD drive is not recognized by the BIOS due to a hardware problem.

  If you can see the STRANGE in the BIOS but are still not able to boot from any disk, then I suppose that the CD/DVD drive cannot read the disk for different reasons.
  One of the reasons could be a defective or damage the laser lens

  > Every so often, I would get an error saying "Media test failure - check cable" or something similar, theres a lot on internet on this subject. I think its something to do if the boot order has CD first, then it has LAN as 2nd.

  Yes, this error means that your laptop tried to boot from LAN

  > In windows, the CD player only reads real CD (audio similar DVD, not CDR and DVDR). This means a failing drive?

  As I said above, it would be possible that the reader s laser lens malfunctions and, therefore, the ODD can't handle the media. It seems that the laser lens can not calibrate properly and can not move in the correct position. This question is not repairable and the drive needs to be replaced.

  > What intrigues me most, however, is that I changed the CD drive with a CD of work of another laptop and windows don't recognize this new CD player at all!

  The fact is that not all CD/DVD drives are compatible due to different master/slave/C-salt settings. You must use the supported players! In most cases, you can find a list in your user manual what CD/DVD readers are compatible.

• Satellite Pro A120 - PSAC1E Modem Driver WinXP

  Hello everyone,

  I have Satellite Pro A120 - PSAC1E and I'm looking to WinXP Driver Modem, can someone tell me where to get it?
  I tried to download driver for this model on the site of Toshiba, but with no luck to find the modem driver that I have found to reset the drivers.

  Thanks in advance.

  Hi dude

  The modem driver was published on the European driver Toshiba page.
  I'm sure because I checked the pilot site and found all the necessary drivers for XP and the modem in the Satellite Pro A120 PSAC1 driver download area.

  May I ask if you have installed the drivers of Toshiba in the right order?
  It is very important.
  Backgrounder statement instillation on the pilot website shows you how to install all the drivers.

  Just a note; You can install the driver for the modem from Device Manager.
  You must mark the unknown device (modem) and have point to the driver files that have been unpacked in the downloaded modem driver package.

  Welcome them

• Satellite Pro A120-154 - how to remove the HARD drive password?

  Hello

  I have the following problem: I set a password for the HARD drive in my old Satellite Pro A120-154 years ago, and now I want to remove or change the passowrd since I'll give you this laptop for my nephew. Instead I don't know the password, I am not able to change or remove, not with the password of Toshiba uitility program and not with the BIOS set up.

  Further I can't find any info on this in the user manual. How can I do this?

  Thanks Tino

  Hello

  I found several useful documents from Toshiba on HARD drive password. Please take some time and pick up some info on HARD drive password and how it works.

  http://APS2.toshiba-tro.de/KB0/FAQ9202JG0000R01.htm
  http://APS2.toshiba-tro.de/KB0/TSB6B01MC000CR01.htm
  http://APS2.toshiba-tro.de/KB0/FAQ9401AR0000R01.htm