Satellite Pro A200-1MA - does not start after disassembly

Similar Questions

• Satellite Pro A200 PSAE4E does not start after upgrading BIOS XP

  Hi, I need help!

  computer laptop, tested just got everything ok with Vista business and everything works fine.
  Now, I have a requirement to test a laptop duel boot XP build and follow the attached instructions to change the BIOS so that I can install XP.

  Restarted the laptop with the bios disk selected bios XP and everything seems ok.
  The phone rings, I answer. When I finished, I think back to the laptop and screen is white.
  Leave it for 20 minutes still white. Stop the laptop and reboot, no tosh start screen, nothing.

  Now does not start, so what do I do to get this thing working again?

  Hey Buddy...

  This looks very bad! :(il ressemble pas à quelque chose a mal tourné àle cours de la procédure de mise à jour dele de BIOS, et donc l'ordinateur portable ne peut pas démarrer correctement.)

  I hope that the ROM module must be flashed again.

  This can be done only by an authorized service provider.
  I see no other solution for contact ASP in your country and ask for help and handling.

  Good luck and best regards

• Satellite Pro A120 (PSAC0E) does not start after upgrading RAM

  Hello

  I hope someone can help me here, I recently bought a Satellite Pro A120 (PSAC0E) and decided to upgrade the RAM. I bought a stick of 512 MB of curries with the following specifications: DDR PC2700 200-pin 333 Mhz SODIMM (64 x 64).

  However, the first problem I encountered was an alignment problem. A little effort and handling solved this, but after you insert the RAM into the available slot, the computer laptop wouldn't boot, and instead, I had the flashing sequence on the LED from 2,3,3.

  I was told it might be a problem matching, then tried to remove the original RAM and booting with just the new stick, still the same error. I tried it in the slots and still no joy. It starts very well with the original 256 MB of RAM, but refuses to take the new RAM.

  Are there any known issues? Can anyone suggest something that I can do wrong? I followed the usual steps of upgrade to remove all power cables and the battery before the upgrade, but still no joy.

  Hoping that someone is able to help!

  Hi James

  You simply have bad memory modules and is not a compatible uses.

  > the first problem I encountered was an alignment problem. A little effort and handling solved this,

  This should not happen! The right modules can be inserted without any problem of alignment!
  Handling can damage the module!

  In my opinion, you should use another and supported the RAM module.

  To my knowledge, you can use the PA3512U-1M1G (DDR2-667 1 GB Memory Kit) or (PA3411U-2M1G) DDR2-533 1 GB
  The two should be compatible.

• Satellite Pro M10 PS630E does not start after upgrading CPU

  I tried to install a new processor for my Toshiba Satellite Pro M10-PS630E.
  He initially has a 1500, I tried to put a 1766.

  I follow the maintenance manual, later the computer change is not star upward.
  When I connet to power it show that the luminous power of orange/amber color and make 5 flashes, then 3 and then restart blinking.

  My question is "is it posible to do a reset of the bios parametrers" or "reset the CMOS?
  Is it possible to get it working again.

  Hello

  The flashing light means that it has detected a hardware problem on the motherboard!
  Perhaps you have used a wrong CPU and is not compatible.

  Perhaps the BIOS does not support this processor and therefore this flashing error code appears.

  What say you can't update the BIOS! First of all, that's not possible since only focused on the victory of BIOS is available for download. You must run the Windows operating system to update the BIOS.
  Secondly the update of the BIOS won't help you with this problem!

  You must use a CPU that is fully compatible!

  Welcome them

• Satellite Pro S300-120 does not start after replacing the CMOS battery

  Hello

  My friends laptop - a S300-120 - was having a few problems.

  I replaced some parts about this before, including a screen crack with no problems.

  However, he began to refuse to start saying "out of battery CMOS, Press F1 to enter setup". Of course you would have to do this, set the date and time, except & restart only to get the same message. We have replaced the CMOS battery with a with the same serial number and now the laptop will not boot.

  It does one of two things.

  It is one) seems to turn, turn to the top disk & CD player, cooling fan is 100%, then flashes the POWER ON led once, twice by orange, and then green to 1/2 second intervals, with no response from the keyboard or LCD.

  Or (b) turns on, turntable, does not turn up to cooling fan, POWER ON witness remains stable, no response from the keyboard or LCD.

  I re-assembled the laptop several times & can not find all the missing fittings or obvious signs of damage.

  The only thing I can think is that the motherboard has been damaged - somehow find replacements is delicate.

  Any ideas?

  Hello

  (> It is a) appears to turn on, turn the disk & CD player, cooling fan goes to 100% and then flashes him

  POWER ON led once, twice by orange, and then green to 1/2 second intervals, with no response from the keyboard or LCD.
  Usually, if the voltage in abnormal feeding malfunctions when IN DC will be blinking orange.

  In my opinion, it looks like a problem with the motherboard :(
  Eventually, you will need to replace the mobo ;(

• Satellite Pro A60 EN does not start after you have used the recovery CD - isapnp.sys missing or damaged

  Help am stuck with it.

  Necessary to perform a recovery on the laptop and used the recovery CD 2 they seem to work OK. No error during installation, but after that they finished and it restarts didn't get the following message.

  Windows could not start because the following file is missing or corrupt:
  System32\drivers\isapnp.sys

  You can attempt to repair this file... etc but I don't have any original installation CD all have is the recovery for the Toshiba.

  I have a setup of Windows XP for the PC disk, but when I try to run which, but it starts just the configuration. Setup is loading files and after the kernel debugger get error

  "File ntkrnlmp.exe could not be loaded.
  The error code is 4, sometimes it's 7.

  I tried to delete and recreate and formatting partitions, so I can see and I can copy a file to the C: drive

  So any suggestions as to what wrong here

  Thank you very much

  I put t know if this Microsoft Knowledge base article would be useful for you, but you should check it out.

  [You receive a "Windows didn't start because the following file is missing or corrupt: Isapnp.sys" error message at startup | http://support.microsoft.com/kb/315311]

  Microsoft has a solution, and I would like to know if you can solve this problem by following the steps of the solution described in the article.

  Feedback would be much appreciated

• Re: Satellite Pro A210, stil does not start after you use the recovery disk

  Hi, my computer laptop girls stopped booting, I tried everything to fix this, but it seems to be on a loop.

  He runs the repair of your computer, but after a while, I get the message, this computer cannot repair this fault automatically (or something similar), there is also a message that says - if you have connected a camera or to this computer's portable music player, remove it now and restart.

  I tried to start in safe mode, safe mode with command prompt and last know good configuration but still no joy, so I eventually ran the recovery disc. Once it was finished, I was to square.

  Does anyone have an idea of what I can try next - other than to throw it out the nearest window.

  Thanks in advance.

  Hello

  Never heard talk of this error but sounds strange
  If I understood your first assignment; you were able to complete the installation of the OS from the recovery disc. Is this good?

  Well, in this case the HARD disk must be OK because the files were copied correctly

  I searched a bit in google and didn t have found a solution to 100%.
  Some have said that new OS install should solve this perhaps you could use clean up Windows Vista, Win XP disk

  You can also try to format the drive HARD integer first. Delete all partitions on the HARD drive, and then try again

  PS: You can check the HARD drive using the + Hitachi Drive Fitness Test. +
  Its free tool. You can find using google

• Satellite A200 PSAEOE does not start after upgrading memory

  Hi, I am first time here.

  I bought a Toshiba A200 PSAE0E-03J02JDR with 2 GB of RAM. I bought a pair of ram Corsair (2 * 2 GB VS2GSDS667D2). The computer does not start after that I installed the memory. I have intel 945 chipset, which is capable of 4 GB (manual page 1-2). The bios version is 1.8 2007.

  Can anyone help me, please.

  Post edited by: Marian ovidiu

  Hello

  The A200 series supports different chipsets;
  Intel 945 PM
  Intel 945GM
  Intel 943GML

  As far as I know your laptop supports the * 943GML * Intel chipset and the chipset supports 2 GB RAM max.
  Take a look at your laptop s user manual * Page 18.*

  Summer: 4 GB of RAM are not possible, and therefore your laptop does not start.

• Satellite Pro A200 - Wifi does not not after loading Win XP

  Hi, I'm new here and I apologies if this has been covered, I searched the Forum but came up to the top with nothing.

  I have a:
  Satellite pro a200
  Windows XP.

  My laptop was xp professional installed and the wifi on Board did not work.
  I had problems with the global laptop but the wifi worked. I formatted last night, installed a new copy of xp home and now wifi doesn't seem to be recognized. The light is on, the switch, but I can't get the laptop to recognize her here.

  I did not much I know, but I hope I can get it sorted.

  You have any questions, I will try and respond with as much information as possible.

  Thank you, my.

  Hello

  Please not that after the installation of Win XP, the BIOS needs to be updated!
  The Toshiba page should provide a special BIOS for Win XP OS update.

  A note of juice; the laptop could be equipped with different WLan modules and so you should be aware of chip right WiFi WLan card would not work if you try to install incompatible driver!

• Satellite Pro A200 - system does not boot

  Hello

  wondering if someone could help?
  My Satellite Pro A200 with windows XP does not start. It starts with the Toshiba screen.
  Then goes to a screen black with text where it says "PXEE61 media test failure - check cable" (I have no cable) then said out of PXErom; moves to the next screen, which lists the options: safe mode; safe mode with networking; safe mode with prompt local; Last Configeration well-known; Start windows normally.

  Which have been tried and results in loading from page turns on for about 20 seconds, then just to abandon and trying all the whole process again (before flashing a blue screen) Windows.

  Nothing seems to work - tried to take the battery on a... number oftimes and the power cable, but nothing helps.
  It's already happened, but after a few false starts gets going - but this time he just don't come out it. I could not take others where locally, but I would prefer not to because I live in Spain and need the laptop as soon as possible and do not know, I want to leave it in some otherwise are hands to the risk of wipe them the hard drive.

  So, I would be very grateful for any help as soon as possible and I fear tech short hand maybe having to explain.

  Thanks a lot, a lot.

  Hello

  I think the problem is that the operating system is not found on the HARD drive.

  The test failure PXEE61 media - check the cable appears especially if the laptop tries to boot from LAN.

  Why the laptop is trying to boot from the local network?

  Well,.

  -option may be the LAN was chosen first in the boot order in the BIOS
  -Maybe the drive is defective and so the laptop is trying to boot from LAN
  -the MBR (master boot record) is may be defective

  I think you should take the Toshiba Recovery CD and need to format the HARD drive and needs to be reinstalled the operating system.
  This should help.

  If not, then the HARD drive could malfunction and should be replaced!

• Satellite A300-15 a does not start after the installation of the alcohol program

  Hello...

  Satellite A300-15 has, I bought yesterday and after completing the installation of Vista, I tried to install "Alcohol" but my judgment of the laptop and now I'm not able to boot up the laptop.
  It does not start in any mode.

  I forgot to make recovery disks. I think that alcohol is not compatible with Vista. Error I get is below.

  Can someone tell me the solution?
  Please help urgent

  "A problem has been detected and Windows has shut down to prevent damage to your computer.
  If this is the first time you've seen this Stop error screen, restart your computer. If this screen appears again, follow these steps: blah blah... "

  Looks like a problem familiar to me, as I had the same one with the Daemon tools. After installing these tools, I couldn't start my Windows XP. I guess that it somehow mixed upwards of some drivers or registry entries, but not sure about that.

  OK, you can try to uninstall tool first start Vista in safe mode (press F8 before Windows starts upward).
  You should then be able to enter in Vista without problem.

• Satellite Pro 6100 system does not start

  Hi people,
  I have the following problem. I used my laptop long enough for thet to deplete battery and the device to go into hibernation. Given the againm battery costs, I tried the system and now it does not start.
  The leds light up fine and stay lit upwards. Just nothing happens, the FN key works. After a minute the fan will start to turn upwards and turns down again. But nothing else.
  After some time, by pressing the power button for a few seconds seems to start the machine, but it stops immediately after 30 seconds. Even if doing a memtest.

  anyboy has any idea what could cause this. I tried to remove the hard disk and start it does not affect what anyone, as does move the RAM module in the other slot. Also remove the CD/RW drive does not affect it. Remove the battery and start also give the same result.

  Hello

  Sorry, but tells you don't know is not enough for me.
  If you start Notepad, you see something on the screen?
  A Toshiba start screen appear?

  You suggested that the FN key works. Have you checked it in windows?
  AFAIK the FN keys can work only if the operating system has been launched and the drivers have been loaded. So my strange question.

  The whole thing is very strange. If nothing is displayed and the laptop cannot start, so I guess a hardware malfunction. But you know without any trial it s not easy to say what's wrong.

  Try to disconnect the laptop from the sector and remove the battery. Wait several times (30 min - 1 hour) then plug the AC adapter and try to start it.
  If it won't work and you know that other devices are ok such as RAM or HARD drive so I think that the technician must check the machine.

• Satellite Pro A200: Wireless does not work

  Hello

  Got a Satellite Pro A200 2 weeks and the wireless worked well.
  Then after a week there was a problem, try to connect. I was able to reboot the pc and he was able to connect.

  Now it just doesn't quite work.
  I can connect through the LAN and I have another laptop that connects to the router with no problems.

  I checked in the Device Manager, the wireless card works correctly and I've updated the drivers for it but no. - GB.

  Any help would be great.
  see you soon

  Hello

  Try to remove the network adapter from Device Manager wireless.
  Then restart the computer and reinstall newest WLan driver that you can download on the page of the Toshiba driver!

  Second, you could try to set up the WiFi network using an Intel ProSet Utility (but only if you have a Wlan Intel card.)

  If you have an Atheros Wlan card, then try using the Atheros Client utility for configuring Wlan

• Satellite Pro L650/L650D does not start

  My laptop Toshiba does not work...

  When he was for a restart, the it closed suddenly... I want to start (start), but when I clicked on the Start button, it does not start... The LED lights were lit, but the laptop does not start...
  At the present time, the lights went out, I don't know how...

  It means that the laptop is break down?
  I hope not, because I don't want to spend more money with that... :(

  Is there someone who could solve this problem?

  Thank you very much, long in advance,
  Raquel

  It is not easy to solve these questions, because nobody knows what is the problem. It may be BIOS related issue or some other hardware related issue.
  It's that there are not a lot of options in this regard.

  You can try to remove the battery and unplug the power supply, press the power button / stop for a while and try again with power running. The same thing happens again?

  > The lights were on, but the laptop does not start...
  You hear cooling ventilation? When the laptop is turned ON it turns off a few seconds later or stays, but without any reaction simply?

• Satellite Pro L850-1DW does not start correctly

  Hello

  I have a client who has a L850-1DW / PSKDHE-00E005EN laptop.

  She keeps pointing out that the computer does not start successfully from the cold.
  She argues that the question arises mainly when the battery starts but sometimes when it is plugged into the mains.
  I can see where point of newspapers that BSOD were registered at the start and that, on more than one occasion, his computer was recovered from a restore of Windows. He has also recovered factory once too.

  Although I've seen the consequences of these issues of "start-up" I have yet to experience first hand with the device.

  I noticed yesterday that the BIOS is outdated (as I had an alert Tempro).
  I upgraded from 1.6 to 6.50. Yet once, I didn't have problems.
  I can't find the release notes for the BIOS so I don't know if this is a known problem that has been fixed.
  I don't know if this "intermittent" defect is just that or if the user has the power button down too hard or for too long and in fact inadvertently crashing NB itself.

  Any suggestion is welcome.

  Otherwise, I guess I have to connect a call with Toshiba.

  On this virtual path, it is not easy to say what the problem is here. In my opinion, you should ask your client if you can make the data backup and install original recovery image. To my laptop computer reviews must be tested with the settings without installation of additional software.

  > I don't know if this "intermittent" defect is just that or if the user has the power button down too hard or for too long and in fact inadvertently crashing NB itself.
  Who knows? Ask your client and show how to start the laptop by pressing the button walk / stop. It must be done slowly and for only one second.