Satellite Pro A200 PSAE4E does not start after upgrading BIOS XP

Similar Questions

• Satellite Pro A120 (PSAC0E) does not start after upgrading RAM

  Hello

  I hope someone can help me here, I recently bought a Satellite Pro A120 (PSAC0E) and decided to upgrade the RAM. I bought a stick of 512 MB of curries with the following specifications: DDR PC2700 200-pin 333 Mhz SODIMM (64 x 64).

  However, the first problem I encountered was an alignment problem. A little effort and handling solved this, but after you insert the RAM into the available slot, the computer laptop wouldn't boot, and instead, I had the flashing sequence on the LED from 2,3,3.

  I was told it might be a problem matching, then tried to remove the original RAM and booting with just the new stick, still the same error. I tried it in the slots and still no joy. It starts very well with the original 256 MB of RAM, but refuses to take the new RAM.

  Are there any known issues? Can anyone suggest something that I can do wrong? I followed the usual steps of upgrade to remove all power cables and the battery before the upgrade, but still no joy.

  Hoping that someone is able to help!

  Hi James

  You simply have bad memory modules and is not a compatible uses.

  > the first problem I encountered was an alignment problem. A little effort and handling solved this,

  This should not happen! The right modules can be inserted without any problem of alignment!
  Handling can damage the module!

  In my opinion, you should use another and supported the RAM module.

  To my knowledge, you can use the PA3512U-1M1G (DDR2-667 1 GB Memory Kit) or (PA3411U-2M1G) DDR2-533 1 GB
  The two should be compatible.

• Satellite Pro M10 PS630E does not start after upgrading CPU

  I tried to install a new processor for my Toshiba Satellite Pro M10-PS630E.
  He initially has a 1500, I tried to put a 1766.

  I follow the maintenance manual, later the computer change is not star upward.
  When I connet to power it show that the luminous power of orange/amber color and make 5 flashes, then 3 and then restart blinking.

  My question is "is it posible to do a reset of the bios parametrers" or "reset the CMOS?
  Is it possible to get it working again.

  Hello

  The flashing light means that it has detected a hardware problem on the motherboard!
  Perhaps you have used a wrong CPU and is not compatible.

  Perhaps the BIOS does not support this processor and therefore this flashing error code appears.

  What say you can't update the BIOS! First of all, that's not possible since only focused on the victory of BIOS is available for download. You must run the Windows operating system to update the BIOS.
  Secondly the update of the BIOS won't help you with this problem!

  You must use a CPU that is fully compatible!

  Welcome them

• Satellite Pro A200-1MA - does not start after disassembly

  This is one for my laptop was overheating strongly and I decided to clean the radiator and the parts around it. I disassembled the computer laptop to the point where I can take off the cooler, cleaned and then I put everything back. The problem is now it won t work.

  It starts normally, past in loading windows (I have Windows 7 sp1) and then after 10 seconds, or it just stops. I tried to go to the bios, but it does the same thing after 10 seconds. First, he showed BSOD with no explanation. Just somewhere stopped working and it has to stop, but I can't figure what. CPU should be fine, it can t overheat in 10 seconds if it s cooler nor starts loading Windows in order to RAM and HARD drive may also be excluded.

  My best guess is that I'm connected to something wrong, but I disassembled it 3 - 4 times today and can t find something that is not connected. When I remove the top plastic I need to disconnect this son: speakers, power button, touchpad, keyboard and one other connectors 2 or 3 which I am sure they are USB, LAN & maybe etc...

  Then, can you at least tell me where to start? What to check?

  Hey,.

  I also can say with certainty what happened exactly, but fact is laptop disassembly is not easy and should be made only to professionals. If you take apart a laptop computer, you must be connected to the land, for example to avoid electrical damage.

  Anyway, everything you can do test your laptop with factory settings (preinstalled OS from Toshiba). If you notice the same problem it s a serious malfunction of hardware and your laptop should be verified professional people.

• Satellite A200 PSAEOE does not start after upgrading memory

  Hi, I am first time here.

  I bought a Toshiba A200 PSAE0E-03J02JDR with 2 GB of RAM. I bought a pair of ram Corsair (2 * 2 GB VS2GSDS667D2). The computer does not start after that I installed the memory. I have intel 945 chipset, which is capable of 4 GB (manual page 1-2). The bios version is 1.8 2007.

  Can anyone help me, please.

  Post edited by: Marian ovidiu

  Hello

  The A200 series supports different chipsets;
  Intel 945 PM
  Intel 945GM
  Intel 943GML

  As far as I know your laptop supports the * 943GML * Intel chipset and the chipset supports 2 GB RAM max.
  Take a look at your laptop s user manual * Page 18.*

  Summer: 4 GB of RAM are not possible, and therefore your laptop does not start.

• Satellite Pro S300-120 does not start after replacing the CMOS battery

  Hello

  My friends laptop - a S300-120 - was having a few problems.

  I replaced some parts about this before, including a screen crack with no problems.

  However, he began to refuse to start saying "out of battery CMOS, Press F1 to enter setup". Of course you would have to do this, set the date and time, except & restart only to get the same message. We have replaced the CMOS battery with a with the same serial number and now the laptop will not boot.

  It does one of two things.

  It is one) seems to turn, turn to the top disk & CD player, cooling fan is 100%, then flashes the POWER ON led once, twice by orange, and then green to 1/2 second intervals, with no response from the keyboard or LCD.

  Or (b) turns on, turntable, does not turn up to cooling fan, POWER ON witness remains stable, no response from the keyboard or LCD.

  I re-assembled the laptop several times & can not find all the missing fittings or obvious signs of damage.

  The only thing I can think is that the motherboard has been damaged - somehow find replacements is delicate.

  Any ideas?

  Hello

  (> It is a) appears to turn on, turn the disk & CD player, cooling fan goes to 100% and then flashes him

  POWER ON led once, twice by orange, and then green to 1/2 second intervals, with no response from the keyboard or LCD.
  Usually, if the voltage in abnormal feeding malfunctions when IN DC will be blinking orange.

  In my opinion, it looks like a problem with the motherboard :(
  Eventually, you will need to replace the mobo ;(

• Satellite Pro A60 EN does not start after you have used the recovery CD - isapnp.sys missing or damaged

  Help am stuck with it.

  Necessary to perform a recovery on the laptop and used the recovery CD 2 they seem to work OK. No error during installation, but after that they finished and it restarts didn't get the following message.

  Windows could not start because the following file is missing or corrupt:
  System32\drivers\isapnp.sys

  You can attempt to repair this file... etc but I don't have any original installation CD all have is the recovery for the Toshiba.

  I have a setup of Windows XP for the PC disk, but when I try to run which, but it starts just the configuration. Setup is loading files and after the kernel debugger get error

  "File ntkrnlmp.exe could not be loaded.
  The error code is 4, sometimes it's 7.

  I tried to delete and recreate and formatting partitions, so I can see and I can copy a file to the C: drive

  So any suggestions as to what wrong here

  Thank you very much

  I put t know if this Microsoft Knowledge base article would be useful for you, but you should check it out.

  [You receive a "Windows didn't start because the following file is missing or corrupt: Isapnp.sys" error message at startup | http://support.microsoft.com/kb/315311]

  Microsoft has a solution, and I would like to know if you can solve this problem by following the steps of the solution described in the article.

  Feedback would be much appreciated

• Satellite L50-A-160 does not start after the Bios Update

  Hi, first of all, this is first post.

  I have 2 satellite L50-A-160 with bios 1.1

  Problem: seems to go to sleep after a few minutes, even working on them (even with both)

  So, I found an updated version 1.9, downloaded and running on one of the laptops. the biosupdate tool found matching the BIOS and a race.
  In the middle of flashing, he fell asleep. turned on and not start. What can I do? Recovery options? I guess the same thing will happen with the other too...

  What is the problem with these computers?

  Besides; very poor battery, always shows 0% available and not charging...
  Does anyone have a solution?

  Best regards
  -always in the hope.
  GT

  Have you tried to change in Power Options?

  See screenshot and try to change the ones I marked (it can refresh the settings, just change the values) and see if this solves the problem.

  

  and for the other laptop with no boot, a laptop sleep by updating the bios will surely mess it.

  what I don't understand is why your sleep laptop BIOS update, as far as I know the sleep settings is active then on windows (since this is controlled by windows)
  He does not sleep while in the BIOS you leave 1 year, sleep settings active only after loading windows.

  have you tried to check the time of processor for your laptop? Maybe its overheating causing auto-off

• Re: Satellite Pro A210, stil does not start after you use the recovery disk

  Hi, my computer laptop girls stopped booting, I tried everything to fix this, but it seems to be on a loop.

  He runs the repair of your computer, but after a while, I get the message, this computer cannot repair this fault automatically (or something similar), there is also a message that says - if you have connected a camera or to this computer's portable music player, remove it now and restart.

  I tried to start in safe mode, safe mode with command prompt and last know good configuration but still no joy, so I eventually ran the recovery disc. Once it was finished, I was to square.

  Does anyone have an idea of what I can try next - other than to throw it out the nearest window.

  Thanks in advance.

  Hello

  Never heard talk of this error but sounds strange
  If I understood your first assignment; you were able to complete the installation of the OS from the recovery disc. Is this good?

  Well, in this case the HARD disk must be OK because the files were copied correctly

  I searched a bit in google and didn t have found a solution to 100%.
  Some have said that new OS install should solve this perhaps you could use clean up Windows Vista, Win XP disk

  You can also try to format the drive HARD integer first. Delete all partitions on the HARD drive, and then try again

  PS: You can check the HARD drive using the + Hitachi Drive Fitness Test. +
  Its free tool. You can find using google

• Re: Satellite A200-1AX does not start after the BIOS update

  Hi all!

  I wanted to install XP on a Satellite A200-1AX.
  So I tried to update the Bios to the version that supports supported XP.

  When I tried to install it, crashed Vista and now the laptop won't even turn on.

  When I keep the power button pressed, the whistling fan but nothing happens.
  I think the BIOS is gone or corrupted.

  What should I do?
  Thanks in advance for any help!

  > When I keep the power button pressed, the whistling fan but nothing happens. I think the BIOS is gone or corrupted. What should I do?

  What to say to boyfriend. It seems that something was wrong during the process of updating the BIOS maybe the BIOS was not written correctly and the ROM module must be flashed again with the help of a special procedure and the tool.

  In this case, you can do anything you will need to contact the ASP in your country for a fix!

  Don t waste time and ask a technician for assistance.

  Good luck and best regards

• Satellite A200-1If does not start after the BIOS update

  Hello

  It is my first time on the forum posting, I hope someone can help me.
  I recently downloaded the latest update of the Bios (bios - 20090121132526.zip) for my laptop. I ran the bios Setup, after the update it restarted my laptop, but then he went to a black screen and no longer start.
  When I press the power button only power led lights, fans begin to turn and the DVD - rom turns and stops and the screen is blank.
  I am running Vista Home premium 32-bit.

  Can anyone provide a solution on what I can do to fix this?

  Was the system standby standby/extended/recovery?

  Its important to cold starts of the system before and after an update of the BIOS.

  You could try to remove one of the modules RAM (change RAM size) and turn on, otherwise the system may need to be sent to an ASP for repair.

• Satellite A200-1CC does not start after upgrade to 4 GB RAM

  I've read several times that I can install 4 GB of ram in this laptop (2 2 GB) but it only works with 2 GB.

  http://www.Corsair.com/Configurator/system_results.aspx?ID=63820

  I bought it here:
  http://www.speichermarkt.de/show.cgi?id=toshiba_satellite_a_200_1_cr_a_200_1_c http://www.UNECE.org/trade/UNTDID/d01b/trmd/gesmes_c.htm & SNO = 00000886

  I know that from Toshiba Web site indicates that it would accept only max 2 GB.
  Two 2 GB ram works, I tested the two of them separate. Also do not work 2 GB more than 512 MB. If it's true that he accepts 2 GB? I run Vista Home Premium 32-bit.
  Thanks a lot for your help! I'm almost about to send the other 2 GB of ram back, but I really want to make it work! ;-)

  I put t know why some dealers offer false information. Maybe you should ask the dealer.
  But you should not forget that the single books supports different hardware specifications and are equipped with different chipsets.
  Some chipsets Intel support 4 GB RAM and some can handle only 2 GB of RAM

  However, you laptop doesn t start because it cannot handle 4 GB of RAM

  Good bye

• FF does not start after upgrading to version 27.0.1

  FF does not start after upgrading to version 27.0.1
  Crash ID: bp-2bc18734-d643-4843-a10f-fd6102140214

  Firefox 27.0.1 is too recent for me to know what unique issues it may have. I will message you a link to download the installer for Firefox 27.0 to see that the inversion or not the problem.

• Satellite P200D-130 does not start after upgrading RAM

  Hi, I just upgraded the RAM on my P200D 130 but it does not start after that.
  I removed the 2 Hynix 1 GB PC2-5200 and put in 2 SO Kingston DDR2 2 GB PC667 (should be the same as PC2-5200).
  Post-market nothing happens, light power control is turned on, I him stays CD drive but screen black, no beeps.

  I put one of the 1 GB modules, it starts normally, then I tried a 1 GB into the lower slot module and a 2 GB module in the top slot and it works.
  I tried a single 2 GB module in each slot, even in the form of 2 2 GB modules.

  What could be the reason, better: what would be the solution to ensure that the modules of 2 x 2 GB to work?

  Thanks in advance,

  Michael

  Hello!

  I think that both modules are not compatible to the laptop.
  Normally you can upgrade your laptop to 4 GB. Look in the user manual.

  The RAM, you should bring the computer dealer and request a new one. More buy modules with the same specifications and dimensions. Try buying RAM with the same specs as before.

  Good bye

• Re: Smoker L30-10 X PSL33E does not start after upgrading RAM

  Hello

  I have a problem with my laptop.
  It has 1024 MB of RAM (2 x 512), but it wasn't enough, so I decided to update to 2048 MB (2 x 1024).

  I bought two modules and my computer does not start after changing them.
  It was only a screen black (same BIOS has not started). I tried another combination of installation of memory modules RAM.
  2 x 1024 - did not work
  1 x 1024 - did not work
  1 x 1024 + 1 x 512 - working but not properly.

  BIOS find that I only 896 MB (1024-128 for the video card)
  I said OK. Let's see what will show windows. He was also 896 MB.
  I launched CPU - Z and it shows that the total size of memory is 1536 MB (medium detect both modules).
  I found that CPU - Z detect 1 module 1 024 MB and 512 MB secondary, but the BIOS detect only 1024 MB 1536. How is that possible?

  I have fought, is that my BIOS is old, then I update the toshiba Web site form most recent version, but the problem persists.
  Please someboy help me and tell what to do.

  PS. the Modules are new and work correctly.
  They have been tested.

  Hello

  Have you used two identical RAM modules?

  What kind of modules did you use?

  In my view, that the problem is related to the new, inserted modules.
  There must be something wrong with the modules or modules are not completely compatible if the laptop can not boot after installation.

  According to a few pages of the book handles the DDR2 533 MHz (PC2-4200) 200-PIN SODIMM modules.

  Did you use these modules?