Satellite Pro L10 does not go on standby mode

Similar Questions

• Satellite Pro L10 does not illuminate

  I have a Satellite Pro L10 and it stopped working yesterday. It won't turn on or charge up. No show of lights on the laptop when the charger is connected. I plugged in another toshiba charger but still no luck.

  Does anyone have ideas on what could be the problem with it and if it is easily resolved. The laptop is about 2 years old. Thanks for your help

  Hello

  Seems not beautiful it is maybe something wrong with the electronic power on the card mother s in this case the motherboard must be replaced to solve this problem

  But maybe you are a lucky guy and only the power adapter malfunctioning Yes, I know that you have tested the laptop with another power adapter, but are you sure that the second captain is supported?

  Anyway, in my opinion, nobody here can provide a solution exactly because without diagnostic tests we don t know what could be wrong
  This is why I recommend to contact the technician of the ASP for a help

• Satellite Pro C660 does not illuminate

  Satellite Pro C660 does not illuminate. no noise, no light just fill out the dead.

  any suggestions?

  Hello

  On this virtual path, it is not possible to provide an accurate diagnosis. All you can do is to unplug the power plug, remove the battery and leave it for a while. Then press the power button and hold it for 15 or 20 seconds.
  After doing this connect the power running and try to start again.

  What happens when you do this?

• The product key on my Satellite Pro P300 does not work

  The product key on my Satellite Pro P300 does not work.
  I entered the key from the sticker on the back of the computer. What I am doing wrong?

  Hello

  Why use this product key?

  Firstly the Toshiba recovery image is already enabled and you don t need this key more activations.

  Second, it's an OEM key and it will not work with other versions of Vista!

  Cheers mate

• Why Satellite Pro A300 does not start when you press the power button?

  Suddenly my new Satellite Pro A300 does not start correctly when you press the power button. The situation is the following: when I press the power button is displayed the opening of Toshiba (Leading Innovation) and the disappers image quickly. Then there is a black screen for about 30 seconds. There is a rectangular frame with the text Microsoft Corporation under. And nothing happens however long wait.

  In order to get with the trial starting I then shut down the computer by pressing the power button until the computer turns off. ("The hard way to close")
  Now, I press the power button shortly to turn on the computer. Then, the computer starts normally with the photo to open Toshiba and after a few seconds, I wonder to open the computer in safe mode or in normal mode. I now choose to open in normal mode and the computer opens normally and is ready to work.

  What should I do to get a normal departure procedure?

  When the laptop starts normally (after choosing normal mode) stop your laptop properly using START > shut down option. Next launch should be normal.

  When the OS is moving towards the low irregularly will always ask you how to start this new (secure or normal mode).
  The same thing happen on my Satellite A300.

• Satellite Pro 4230 - does not light

  Hello
  I have the following problem:

  A Satellite Pro 4320 will not feed, DC-in light is on (green), with inserted (quite old) battery, the quickly flashes orange, (charge of compensation, according to manual) battery. If I press the power button / stop, DC-In goes off for half a second and turns on, that of all, nothing else happens.
  The power supply is 15V 4Amps one correct, I load tested it works and provides all the power, according to the specifications. It does not matter if the battery is inserted or not.

  Now the question: is this a battery problem or there is a problem with the entrails of laptops (internal DC converter)? Normally, your laptop should work on the included power supply.

  Best regards
  Nohab.

  Hey,.

  > Normally a laptop should work on the included power supply.
  You're absolutely right, mate. All cell phones work with power supply only, theoretically, a battery is not necessary. That's only important if you want to work without power, otherwise laptop mobile working with power supply only. No battery is needed.

  So my personal opinion it of a card mother dysfunction :(

• Satellite Pro A10 does not start - no hard drive

  MY TOSHIBA SATELLITE PRO A10 PRIMER NOT.
  WHAT I GET IS NO DRIVE DETECTED. TRIED TO REINSTALL XP BUT STILL NO LUCK.
  CAN EVERYTHING-ONE PLEASE HELP AS I AM PULLING MY HAIR OUT TRYING TO THINHK HOW TO SOLVE THIS ANNOYING PROBLEM.
  DOES ANY - ONE KNOW WHERE I CAN DOWNLOAD A RECOVERY DISC SO I CAN TRY THIS OPTION.

  Hello

  HARD drive is visible in the BIOS?
  If this isn't the case, then this means that the HARD drive is faulty.
  Try to replace the HDD with a compatible and try again.

  Good luck

• Satellite Pro L10 will not start the system

  Hello!

  I have a Toshiba Satellite Pro L10, which won't work for some reason any.

  The last time that I used it, it worked perfectly fine, but now all I get is a black filtered message on "windows starts do not successfully»

  It indicates that the computer is not responding and asked me to choose one of the five options - safe mode, safe mode with network, security mode command, last known configuration, prompt or start windows normally.

  There is also a 30 second countdown if I do nothing the portable samekh automatically.
  It is, none of these things work.

  Everything that happens with any option is to a thought very much time on things, then it goes to a black screen with a time/processing bar downstairs, then when that ends it turns itself off, samekh, mw windows page shows (with f2 and f4/f10? options) and the process is repeated.

  He did about 50 times now and still nothing.
  I tried the command ctrl/alt/del, I tried to turn if off and try again, I even opened the f options but I don't know enough about computers to do more.

  Help, please!

  If possible I would like to get the computer on long enough to verify what documents I have on this subject before I can back up (if necessary) and restore it to the factory settings (as I predicted), or if this is not possible, I do not think that there is a lot to lose in this respect in any case, am prepared to take it all back to factory if necessary. I have all necessary installation CD and manuals to go with.

  hope this makes sense and I gave you all you need to know.

  Thanks, B

  It seems that the laptop is not able to boot the system, but I m not quite sure if it s because of the defective system or HARD drive corruption.
  If it s just a system problem, the installation of the new Windows operating system should help you to get it resolved.

  In case the HARD disk is defective, you need to replace the HARD drive and reinstall the system.

• Satellite Pro L300 - does not start form DVD

  Problem: my Satellite Pro L300 will not start no optical drive (DVD)

  Leisure problem scenario:

  Insert the DVD Toshiba recovery in optical disc drive,
  Restart and during the boot prompt, press F12 and select the optical drive.
  Black screen and the cursor flashes in the upper left corner... after the seconds flew L300 starts to beep loudly. No message on the screen.

  Reports of BIOS version 1.50 while the latest version of the BIOS update on the web is to 1.40...

  Model No.: PSLB1E-02200GG3
  Serial 78685377Q

  I'm doing this because I want to change the OS from Vista to XP.

  Hello

  Stand by. You mean you are using a Toshiba original WXP for Satellite Pro L300 recovery CD/DVD or what?

  Have you tested with any other CD bootable (Linux)?

• Satellite Pro C650 - does not start

  Hey all,.

  My Satellite Pro C650 boot not beyond a certain point. I tried to start in all modes different for example safe mode, mode of networking,

  However this proved unsuccessful, the laptop freezes and I meet a constant and regular beep at the same point every time that I try to start. I even tried to start Linux 12.04 USB to see if it's hardware or software, unfortunately is the same, which means hardware failure.

  The problem is that I don't know the bios beep codes and I can't understand what needs fixing.
  I was hoping you could help me!

  Thanks :)

  I think you need professional help with this problem. I don't know if your laptop is always guaranteed to be valid, but in my opinion, you should contact the nearest Toshiba authorized service provider and ask for help. They have special diagnostic tools and hardware malfunction can be detected and repaired.

  For the addresses and phone numbers, visit http://www.toshiba.eu/innovation/generic/ASP_SUPPORT/

• Satellite Pro M40X does not ILLUMINATE

  Hi. -.

  I have a M40X Pro Satellite that I bought 4 years ago. It works well until a few weeks ago.

  I tried to turn it on but nothing happen, nothing, no lights, no sound at all, completely dead.

  It is connected to the power supply and the power light is on, (the battery light does not work since there is a lot of time). I tried to remove the battery, unplug the power cable and after several hours or even days, try to turn it on and I got the same behavior.

  Only power if it is (the power light when you connect the AC power) but when I press the button "turn on" the laptop, nothing happens.

  My laptop isn't under warranty, so if someone could help find a solution that would be great!

  Thank you

  Hello

  I have read your problem related to the failure of hardware. It seems that the motherboard is dead, no doubt, the southbridge. In any case, you should contact the service center:

  http://EU.computers.Toshiba-Europe.com/innovation/generic/ASP_SUPPORT/

  Note that the motherboard is one of the most expensive parts of the tower and don't know if it's worthy to replace, it is better to buy a used or a new laptop.

• FN + F10/F11/F12 in Satellite Pro U300 does not work

  Guys,

  need your help...
  I have the Satellite Pro U300 series and most recently the numbers four and six obtained busted... its does not work so I try to use the superposition of numeric keypad but I have observed that after pressing FN + F11 nothing happens...

  Please help me...

  Thank you
  <>

  Hello

  When you use FN + F11 small control LED must be lit and the keypad must be enabled.
  If your laptop is preinstalled with Toshiba recovery image this option SHOULD work correctly.

  So nobody here knows what you did with your laptop and why these options are not available more.
  Before you start with advice how to get this working again once please let us know what operating system is preinstalled on your Satellite Pro U400.

• Cannot install Win 8 - Satellite Pro C660 does not detect HARD drive

  Hello

  My HARD drive died, so I decided to upgrade my Satellite Pro C660 - 1 9 to an SSD.
  I made a USB bootable with Win8 and starts very well.

  The problem is that it does not detect my SSD, so I can proceed with the installation.
  SSD appears in BIOS but not in Windows Installer.
  He said that there is a missing driver.

  I downloaded the AHCI drivers (XP, only ones available) and even in this case, after you have selected the only rider that appears, it says no new device found.

  I tried to change the SATA from AHCI mode to compatibility mode and it's the same thing...

  What can I do?

  Thanks for the help.
  Best regards
  Bruno Moreira

  More old Windows XP need a driver AHCI Intel's but I think this isn't a problem with SATA driver missing because as far as I know Windows 8 as well as Win 8.1 already contains the drivers to recognize the SSD or HARD disk drive.
  In addition, the installation of the OS should be possible even if the driver would be added for this procedure, you must use the "compatibility" mode
  As you say, the compatibility mode is not working too, so I think there is another problem.

  However, page driver Toshiba also provides a driver Intel RST (Intel Rapid Storage Technology) (Windows 8 - updated) you can try to add during the installation of the OS.

  But I m wondering if you would be able to install this Win 8 on common SATA HDD.
  Have you tried to format the SSD using a different computer, then install Win 8?
  Give it a try.

• Satellite Pro M40X does not work with battery

  Hello

  I have toshiba satellite pro m40x laptop. It haves apromaly 11 months.
  In recent weeks, the laptop does not work with the battery.
  With the battery and the power running, if I turn on the laptop, it turns off after 10 seconds. If I only turn the computer batteries, laptop not respons.
  The laptop works without battery.

  I have rma is not the portable and the technical suport fixed the battery because it only 6 months guarantee.

  I'm sure that battery modules were not upset because I used the battery not very often.
  I disassemble and I wached the control circuit. I'm sure that something of them, it was broken, but I can't fix it without the schema.

  Another question is if I can change the graphics card to laptop. Is actually a x600se but I need power more graphic

  I hope you can help me

  gretings

  Hello

  It is not easy to say what the problem is here. Have you noticed something strange with LED power control? It is also possible that the electronic power supply do troubled. Try to talk with authorized Toshiba and explain the situation. If you open only one Notepad, uneducated, it may be simply worse.

  Graphics card cannot be updated as on desktop computers. I put t know how it is on this model laptop but the graphics card is fixed on the motherboard and cannot be traded.

• Satellite Pro 480CDT does not start (even in BIOS)

  Hi all

  I just hand on a Toshiba Satellite Pro 480CDT

  I had to work with the original power supply (on an inverter plugged into my 12v cars I wasn't close to 240 v power outlet)

  It worked very well, it boots into Windows 98 and I played with a few programs (Media Player and defragmentation)

  I got it defragment for about 5 minutes, while charging via the car converter, however it froze and I had to hold the power button to restart.

  When I tried to next turn on the screen remains empty, the hard drive is not turn and there is only the power LED and battery LED that lights up.

  He let me press the function key that lights up the fn LED on top of the keyboard, but then after a few presses of lighting stops.

  I opened the case and concluded that there are two batteries of the bios, the look at where they are plugged into the main Board, there is green type of corosion on the pins, I removed the plugs (who might add when it is very difficult to remove because of the coros), I cleaned the plugs (male & female) with a pen of WD40 and plugged in I got a voltmeter on them and they demonstrate tension and also show higher voltage when the power supply for laptop is connected, then it means they are load or at least tension.

  After doing this I go up the laptop, but it still suffers from the same problem?

  Please what could someone help or give me a little advice? My next event is the power supply Board but wanted to get some ideals before hand.

  Thanks in advance.

  Pete

  > after doing this I go up the laptop, but it suffers still from the same problem?

  His pity to hear that your baby dead :(
  But if we move to a diagnosis of material, I doubt someone here might be able to point in the right direction if his motherboard problem, it would be really difficult to solve this problem without using special tools, circuit diagram of motherboard and of course experience

  I think you should check the modules memory vivid faulty ram could affect the laptop everything is just speculation