Satellite Pro L10 - low speed USB

Similar Questions

• Can I get my satellite Pro 2100 high-speed USB 2.0?

  I have a new MP3 Jukebox that can operate at USB 2.0. Do anything to get my Satellite Pro 2100 to work at speed 2.0 that it currently only works with USB 1.1? Sorry, but I'm not very technical.
  Hope someone can advise me
  See you soon
  Bob

  Hi Bob

  The best solution for you is to buy a PCMCIA USB 2.0 card. As far as I know there are cards with two or four USB ports. This card is not expensive and the installation is not complicated.

• Installation of SP2 on my Satellite Pro L10 causes the USB ports fail

  I just installed XP SP2 on my L10 and USB ports no longer work.
  There is no error in the Device Manager, the device in the USB ports are not recognized.

  I removed SP2 and USB ports are functioning again.
  Model No.: PSL15E-00H018EN

  Any suggesttions? Thanks in advance.

  You simply remove the USB controller from Device Manager.
  After that the new charging USB ports should work again!

  Also see this MS article:
  http://support.Microsoft.com/kb/892050/en-us/

• Satellite Pro L10-103 - USB ports not working not

  Hi, my Satellite Pro L10 - 103 USB Ports do not work. I tried different things and finally my Advisor rubbed my computer clean of all programs and operating system. After reloading of the set up disc and having lost my dear some programs I am no further forward. It still does not.

  Anyone know if this means that it is a mechanical problem with the computer? (I use Windows XP). Your help would be greatly appreciated.

  Hey Buddy,

  As wrote Akuma did you use the Toshiba Recovery disk or the Microsoft Windows disk?

  After installing XP, make sure that Service Pack 3 is installed. It contains important updates and can be downloaded on the official page of Toshiba.

  In addition, try to remove all the USB ports on the Device Manager, restart the computer. Ports will still be recognized and ready to use once.

• Satellite Pro L10: USB on and goes off when I try to use the USB modem

  I have a mobile broadband usb t-mobile I want to use it on my Satellite Pro L10.
  When I attach to one of the usb ports then the laptop it is, but it loses then every 10-15 seconds (without interruption).

  I'm on XP Pro and usb Sockets work very well for a USB and a printer.
  I also tried to fix via a hub with external power usb and a pcmcia card with usb port, with exactly the same results.

  It works perfectly on my wifes laptop, it seems to be a conflict or a software problem.
  I flashed the bios and updated as well as seems relevant that I can.
  I continue updating the drivers etc, but in the meantime, I was wondering if anyone had any bright ideas?

  A healthy idea of mind is considered, it is starting to drive me up the wall! Mike

  Hey Buddy,

  T-mobile USB broadband have you? I mean if you could tell us what model you have maybe we can discuss it further. By the way: you said about your wife the USB - stick works machine. What operating system your computer laptop wife´s have?

  Would be interesting to know these facts; either by the way, I think it s more programs given that your material seems fine.

  Would appreciate feedback of your regarding your question.

  Greetings

• How to use Recovery on satellite Pro L10 with DVD drive broken?

  Hello...

  I have a satellite Pro L10, which is virused. I need to recover Windows. Unfortunately, I can not, because the CD/DVD drive is borked.

  I tried everything until and including the purchase of a laptop adapter HD, but my desktop computer is not a Toshiba so he does not have the recovery disk.

  I've never had to use a "recovery disk" before, so I have no idea how it works - apparently there should be a folder on my hard drive recovery? can someone tell me where I could find it? (I'm quite familiar with the innards of my installation of Windows and have never noticed before). Also, is it possible that this native recovery file has been compromised by my virus?

  Default: can it be fixed using an installation of LAN, and if so, could someone point me to instructions? (My BIOS allows booting from LAN, but not USB, which is irritating).

  Any other suggestions would be welcome.

  Thank you.

  Hello

  First of all you will not be able to use the Toshiba Recovery disk if you cannot use the CD/DVD drive.
  Why? Because you need to boot from the CD of recovery if you want to install windows from the CD from Toshiba.

  You ask how to boot from LAN?
  Well friend; I doubt that you will be able to do.
  First of all that this could be possible only if you have a RIS server.
  The Remote Installation Services can be installed optionally on Microsoft Windows 2000 Server, Windows Server 2003 or Windows Server 2008.

  It's really complicated and not easy for someone who has never done.
  If you want you can google a little how to create REEFS but in my opinion it s advisable to buy and compatible CD/DVD drive because the STRANGE can also be used for other purposes

• WLan signal is poor and often loses connection - Satellite Pro L10

  I have a Satellite Pro L10 and a home network, where I used two Belkin and Netgear Routers ADSL Wireless.
  My L10 always reports very low signal and often loses the signal unless I'm VERY close to the router.
  I have three laptops and a desktop at home and they all have very high or excellent signal.

  I changed my router and even installed a Netgear wireless card in the L10 (in case there is a problem with the Intel Pro/Wireless 2200BG, but he pointed out again and again a weak signal.

  Someone else had this problem?

  Hello

  Try please install the latest driver designed by Intel. You can find it on http://downloadfinder.intel.com/scripts-df-external/Product_Filter.aspx?ProductID=1637&lang=eng

  Good luck!

• Satellite Pro L10 - Unmountable Boot Volume

  My Satellite Pro L10 loops in the boot process. After the Windows XP splash screen, the following error messages appears:... Unmountable boot volume... Technical information: Stop: 0x000000ED...

  I know that is nothing exceptional and do a full restore would solve the problem. But I don't want to lose the data (which are of course not saved). I tried a Windows XP disk, but it does not start from the cd/dvd drive by pressing F12 or <0>and change the boot order...

  Can anyone help please?

  Hello

  Hmm, the volume not mountable startup error message appears especially if the HARD drive may not be recognized during initialization. Why? Well, maybe the HARD drive failures or the master boot record is defective!

  If you don t want to recover the laptop, you can try to boot from the XP CD (C press immediately after switching on the laptop) and to start the repair console.

  In the repair console, you can use the command chkdsk/p and after that, you could fix the disk main boot using the fixboot command or / and fixmbr.

  If this does not help, the new installation of the OS is that you as a last resort.

  PS: If you want to save the data you can try to remove the HARD drive and try to connect it via external USB HDD controller to another computer.

• Satellite Pro L10 and Windows 7 drivers

  Hi guys,.

  I'm looking for a set of drivers for the laptop model above. I recently installed Win7, but I have no drivers for the machine at all.
  XP drivers do not work.
  If someone managed to install the drivers for this machine? I'm mainly interested in getting my wireless card working.

  I look forward to your responses.

  Thanks in advance for your responces
  Panos

  Satellite Pro L10 is old enough for laptop and I do not think that you will find all the Win7 drivers.
  According to the Toshiba - http://aps2.toshiba-tro.de/kb0/TSB9902P50000R01.htm - your laptop isn't supported Win7 and find the drivers won't be so easy.

• Extension memory Satellite Pro L10

  Hello

  I have a satellite Pro L10, which has only 128 MB of RAM. I want to wear this but can't find any information about it in the manual.
  I would like to know,

  How much RAM, I put in the L10?
  What type of RAM the L10 take?
  It's like a stick or two?
  Where can I buy this type of RAM?

  concerning

  David U

  Hey there,

  It has no internal memory, 2 locations available, 128 or 256 MB at 1 location, PC2100 DDR - RAM 333 MHz, 1024MB max

  You can buy the RAM from all :) any store on the computer or online from Toshiba.

  See you soon

• Satellite Pro L10 Memory Upgrade

  Hello

  I have a Satellite Pro L10 Celeron M Processor 360 1.4 GHz / XP HE / 256 MB / 40 GB / 15TFT / DVD-CDRW / OneNote. I wanted to upgrade the RAM, and I noticed that in the manual it says:

  Before installing a new module memory 512 MB do not forget to remove already installed memory modules.

  Does that mean that I can not install a 512 MB module and more the 256 MB is already a total of 768 MB?

  Thanks for any advice,

  Luis

  Hi Luis,.

  The specifications of your laptop indicates that it can accept up to 1 024 MB of RAM. If you have 2 RAM slots, so you can use any combination of modules of RAM as long as you do not exceed the maximum quotes. Of course if you have only 1 RAM slt then you must remove the original 256 MB module before insert you new 512 MB a.

  HTH

• Satellite Pro L10 will not start the system

  Hello!

  I have a Toshiba Satellite Pro L10, which won't work for some reason any.

  The last time that I used it, it worked perfectly fine, but now all I get is a black filtered message on "windows starts do not successfully»

  It indicates that the computer is not responding and asked me to choose one of the five options - safe mode, safe mode with network, security mode command, last known configuration, prompt or start windows normally.

  There is also a 30 second countdown if I do nothing the portable samekh automatically.
  It is, none of these things work.

  Everything that happens with any option is to a thought very much time on things, then it goes to a black screen with a time/processing bar downstairs, then when that ends it turns itself off, samekh, mw windows page shows (with f2 and f4/f10? options) and the process is repeated.

  He did about 50 times now and still nothing.
  I tried the command ctrl/alt/del, I tried to turn if off and try again, I even opened the f options but I don't know enough about computers to do more.

  Help, please!

  If possible I would like to get the computer on long enough to verify what documents I have on this subject before I can back up (if necessary) and restore it to the factory settings (as I predicted), or if this is not possible, I do not think that there is a lot to lose in this respect in any case, am prepared to take it all back to factory if necessary. I have all necessary installation CD and manuals to go with.

  hope this makes sense and I gave you all you need to know.

  Thanks, B

  It seems that the laptop is not able to boot the system, but I m not quite sure if it s because of the defective system or HARD drive corruption.
  If it s just a system problem, the installation of the new Windows operating system should help you to get it resolved.

  In case the HARD disk is defective, you need to replace the HARD drive and reinstall the system.

• Satellite Pro L10 - what sound card I have?

  Can someone tell me please what sound card has the Satellite Pro L10?
  All I know is that it is an integrated, but need to find the drivers for it, as I don't have my original master computer disc with me here in College, but to do my sound!
  Thank you
  Rob

  [Edited by: admin on 22 January 06 08:58]

  Hello

  Your device has Conexant CX20468-31 AC97 Audio Sound Card.

  Good bye

• Satellite Pro L10: Enter key malunction

  Hello.

  On my Satellite Pro L10, the Enter key does not work. I tested it in the BIOS and it works but it does not work in Windows XP. If someone from the software fixes or advice I would be very grateful

  Hello

  It's a very strange question, but you should be more specific about this. How did you test the feature key of entry? Is there the same result if you use Notepad or the same conversation programs Office applications? Your device's pre-installed with recovery media?

  As much as I know it isn't common Windows problem and it is unclear to me that there is a patch for this problem.

• IRQ conflict on satellite pro L10

  I had problems using a capture card to PCMCIA data with a new satellite pro L10. I used the same card on other laptops with no problems. I think the problem is to do with the conflict on the IRQ channel, because both the card and the controller cardbus use the same channel. I tried to change the IRQ channel manually with the Device Manager, but it does not accept the change. Someone has suggestions how to change the IRQ channel or anything else that might help?

  Hello

  Unfortunately I'm not familiar with this, but please check this article http://kadaitcha.cx/irq_conflicts.html maybe you will find the solution to your problem.

  Good luck!