Satellite Pro M10 PS630E does not start after upgrading CPU

Similar Questions

• Satellite Pro A200 PSAE4E does not start after upgrading BIOS XP

  Hi, I need help!

  computer laptop, tested just got everything ok with Vista business and everything works fine.
  Now, I have a requirement to test a laptop duel boot XP build and follow the attached instructions to change the BIOS so that I can install XP.

  Restarted the laptop with the bios disk selected bios XP and everything seems ok.
  The phone rings, I answer. When I finished, I think back to the laptop and screen is white.
  Leave it for 20 minutes still white. Stop the laptop and reboot, no tosh start screen, nothing.

  Now does not start, so what do I do to get this thing working again?

  Hey Buddy...

  This looks very bad! :(il ressemble pas à quelque chose a mal tourné àle cours de la procédure de mise à jour dele de BIOS, et donc l'ordinateur portable ne peut pas démarrer correctement.)

  I hope that the ROM module must be flashed again.

  This can be done only by an authorized service provider.
  I see no other solution for contact ASP in your country and ask for help and handling.

  Good luck and best regards

• Satellite Pro A120 (PSAC0E) does not start after upgrading RAM

  Hello

  I hope someone can help me here, I recently bought a Satellite Pro A120 (PSAC0E) and decided to upgrade the RAM. I bought a stick of 512 MB of curries with the following specifications: DDR PC2700 200-pin 333 Mhz SODIMM (64 x 64).

  However, the first problem I encountered was an alignment problem. A little effort and handling solved this, but after you insert the RAM into the available slot, the computer laptop wouldn't boot, and instead, I had the flashing sequence on the LED from 2,3,3.

  I was told it might be a problem matching, then tried to remove the original RAM and booting with just the new stick, still the same error. I tried it in the slots and still no joy. It starts very well with the original 256 MB of RAM, but refuses to take the new RAM.

  Are there any known issues? Can anyone suggest something that I can do wrong? I followed the usual steps of upgrade to remove all power cables and the battery before the upgrade, but still no joy.

  Hoping that someone is able to help!

  Hi James

  You simply have bad memory modules and is not a compatible uses.

  > the first problem I encountered was an alignment problem. A little effort and handling solved this,

  This should not happen! The right modules can be inserted without any problem of alignment!
  Handling can damage the module!

  In my opinion, you should use another and supported the RAM module.

  To my knowledge, you can use the PA3512U-1M1G (DDR2-667 1 GB Memory Kit) or (PA3411U-2M1G) DDR2-533 1 GB
  The two should be compatible.

• Compaq 6200 PRO MT: Makes the computer does not start after upgrade CPU

  I have the HP Compaq 6200 PRO PC of MT 615114-001 motherboard and processor Intel Celeron CPU (LGA 1155). After I changed the CPU for Intel Core i5 (LGA 1155) computer does not start. He begins a minute (less than one second) and stops again. No beeps. After you have installed the Celeron back everything works fine. i5 CPU is brand new. What can be?

  In my previous post, I explained the reason it has not worked, and listed the CPU that will work.

  HP tests CPU in the laboratory and publishes a list of processors that will work in a notebook.

  Notebook motherboard BIOS has a list of processors that will work. If it is installed, which is not encoded as OK in the BIOS ROM file, then this will not work.

  Processors published (in the maintenance guide & Service for your nttebook series model) are available in models that can be deilvered in State CTO (configured to order).

• Tecra A11 - 11N does not start after upgrading CPU

  Hello

  I would like to do an upgrade of the processor for my Tecra A11 i5 - 430 M 11N to a probably much faster i5 processor. I thought that the i5 - 580 M'd, but the laptop does not start when I installed this processor.

  I started the 430M, done some research on the internet and discovered that the 580 M has a very high FSB speed, and that is what probably does not work / not compatible with my machine.

  http://Ark.Intel.com/products/43537/
  http://Ark.Intel.com/products/49653
  http://Ark.Intel.com/products/49652

  and also http://ark.intel.com/

  Now, I went back to the computer store, returned the 580M and got an i5 - 560 M compared to its specifications as I've seen it would not compatible because it has the same speed of the FSB with the 430 M.

  I then later in the day tried to install this cpu as an upgrade, BUT alas!
  It STILL does not START ALSO.
  I was dumfounded left. The processors in the same line of the family are supposed to be compatible between them provided: lithography, FSB and socket type are similar.

  Or what I'm missing here?
  I did upgrades of CPU in many cases for desktop computers and laptops, and this is the first that has left me with no word to say!

  Please offer assistance or advice.

  Simon

  + The message has been modified.

  Hello

  Recommend to check this doc from Toshiba:

  + Can I put th CPU, screen, or motherboard in my Toshiba laptop? +
  http://APS2.toshiba-tro.de/KB0/FAQ35006D000RR01.htm

  Upgrading the CPU is not supported (officially).
  The point is that, even if the chipset would support the new processor, it would be possible that the laptop wouldn't start because of compatibility problems between the BIOS or other components on the motherboard and the new processor.

• Satellite Pro S300-120 does not start after replacing the CMOS battery

  Hello

  My friends laptop - a S300-120 - was having a few problems.

  I replaced some parts about this before, including a screen crack with no problems.

  However, he began to refuse to start saying "out of battery CMOS, Press F1 to enter setup". Of course you would have to do this, set the date and time, except & restart only to get the same message. We have replaced the CMOS battery with a with the same serial number and now the laptop will not boot.

  It does one of two things.

  It is one) seems to turn, turn to the top disk & CD player, cooling fan is 100%, then flashes the POWER ON led once, twice by orange, and then green to 1/2 second intervals, with no response from the keyboard or LCD.

  Or (b) turns on, turntable, does not turn up to cooling fan, POWER ON witness remains stable, no response from the keyboard or LCD.

  I re-assembled the laptop several times & can not find all the missing fittings or obvious signs of damage.

  The only thing I can think is that the motherboard has been damaged - somehow find replacements is delicate.

  Any ideas?

  Hello

  (> It is a) appears to turn on, turn the disk & CD player, cooling fan goes to 100% and then flashes him

  POWER ON led once, twice by orange, and then green to 1/2 second intervals, with no response from the keyboard or LCD.
  Usually, if the voltage in abnormal feeding malfunctions when IN DC will be blinking orange.

  In my opinion, it looks like a problem with the motherboard :(
  Eventually, you will need to replace the mobo ;(

• Satellite Pro A60 EN does not start after you have used the recovery CD - isapnp.sys missing or damaged

  Help am stuck with it.

  Necessary to perform a recovery on the laptop and used the recovery CD 2 they seem to work OK. No error during installation, but after that they finished and it restarts didn't get the following message.

  Windows could not start because the following file is missing or corrupt:
  System32\drivers\isapnp.sys

  You can attempt to repair this file... etc but I don't have any original installation CD all have is the recovery for the Toshiba.

  I have a setup of Windows XP for the PC disk, but when I try to run which, but it starts just the configuration. Setup is loading files and after the kernel debugger get error

  "File ntkrnlmp.exe could not be loaded.
  The error code is 4, sometimes it's 7.

  I tried to delete and recreate and formatting partitions, so I can see and I can copy a file to the C: drive

  So any suggestions as to what wrong here

  Thank you very much

  I put t know if this Microsoft Knowledge base article would be useful for you, but you should check it out.

  [You receive a "Windows didn't start because the following file is missing or corrupt: Isapnp.sys" error message at startup | http://support.microsoft.com/kb/315311]

  Microsoft has a solution, and I would like to know if you can solve this problem by following the steps of the solution described in the article.

  Feedback would be much appreciated

• Laptop does not start after upgrading CPU

  Hello

  I have a dv2528ea and I decided to upgrade the processor and the RAM. According to the manual of the T8300 is compatible, so I bought one on eBay (so-called new). When I powered the laptop, the bios screen appeared as usual, but nothing more happens. Among the options available in this screen only works the "ESC" (boot messages I think). I can't access the configuration. The CPU, RAM, HARD drive and DVD drive is correctly detected, the BIOS and video BIOS are "shaded" don't know what it means.

  I know that I didn't break something because after putting the T7100 back in place, the computer worked fine.

  So my question is: is the burned T8300? Do I have a bios problem?

  I've never updated my bios (since 2007) and the CPU is not physically damaged, but this last part can doesn't mean anything...

  Thanks in advance, Pedro.

  Hi, Pedro.

  I hope it will do the trick.  F.0Une is old and I think that's the reason why your processor does not work.

  The problem is that you are under Windows 7.

  You can put Vista on it and flash, or do you know how to make a flash out of the file based BACK?

  I don't know how.

  I'm saying that you are taking a considerable risk if you flash in Windows 7.

  Paul

• Dell Dimension 4600 does not start after upgrading CPU

  Hello

  First of all, I tried to send this last night but received a message on my post approval by moderator? Not yet been approved but seen other people have posted with success more recently. Do not know what is happening.

  In any case, put his hand on a 3.4 Ghz HT P4 Northwood 512 Kb 800 Mhz FSB for £10 on Ebay to upgrade my mother enough old Dimension 4600 which has a 2.8 Ghz P4 512 KB 533 FSB inside... However, when I install it the computer does not light and shows just a light amber. The readers and fans still spin but there is no display. The computer works normally when I put the old one back in.

  I think somehow it is a power supply problem as the new processor uses 20w more energy than the old 2.8 Ghz one. Someone at - it ideas? Just trying to figure if I bought a bad CPU, so I can return.

  Thank you

  Andrew

  AV115

  Hello

  First of all, I tried to send this last night but received a message on my post approval by moderator? Not yet been approved but seen other people have posted with success more recently. Do not know what is happening.

  In any case, put his hand on a 3.4 Ghz HT P4 Northwood 512 Kb 800 Mhz FSB for £10 on Ebay to upgrade my mother enough old Dimension 4600 which has a 2.8 Ghz P4 512 KB 533 FSB inside... However, when I install it the computer does not light and shows just a light amber. The readers and fans still spin but there is no display. The computer works normally when I put the old one back in.

  I think somehow it is a power supply problem as the new processor uses 20w more energy than the old 2.8 Ghz one. Someone at - it ideas? Just trying to figure if I bought a bad CPU, so I can return.

  Thank you

  Andrew

  AV115

  Andrew,

  It is not a power supply problem, it's incompatible, or a bad processor problem.

  The first models of 4600 will take up to 3.0 GHz and models later, 3.2 GHz to 3.4 GHz, but this does not offer much of a sudden boost on the 3.0 GHz

  Motherboard Dell P/N F4491 will support up to 3.4 Ghz Northwood leaving Prescott

  Bev.

• Satellite Pro A200-1MA - does not start after disassembly

  This is one for my laptop was overheating strongly and I decided to clean the radiator and the parts around it. I disassembled the computer laptop to the point where I can take off the cooler, cleaned and then I put everything back. The problem is now it won t work.

  It starts normally, past in loading windows (I have Windows 7 sp1) and then after 10 seconds, or it just stops. I tried to go to the bios, but it does the same thing after 10 seconds. First, he showed BSOD with no explanation. Just somewhere stopped working and it has to stop, but I can't figure what. CPU should be fine, it can t overheat in 10 seconds if it s cooler nor starts loading Windows in order to RAM and HARD drive may also be excluded.

  My best guess is that I'm connected to something wrong, but I disassembled it 3 - 4 times today and can t find something that is not connected. When I remove the top plastic I need to disconnect this son: speakers, power button, touchpad, keyboard and one other connectors 2 or 3 which I am sure they are USB, LAN & maybe etc...

  Then, can you at least tell me where to start? What to check?

  Hey,.

  I also can say with certainty what happened exactly, but fact is laptop disassembly is not easy and should be made only to professionals. If you take apart a laptop computer, you must be connected to the land, for example to avoid electrical damage.

  Anyway, everything you can do test your laptop with factory settings (preinstalled OS from Toshiba). If you notice the same problem it s a serious malfunction of hardware and your laptop should be verified professional people.

• Re: Satellite Pro A210, stil does not start after you use the recovery disk

  Hi, my computer laptop girls stopped booting, I tried everything to fix this, but it seems to be on a loop.

  He runs the repair of your computer, but after a while, I get the message, this computer cannot repair this fault automatically (or something similar), there is also a message that says - if you have connected a camera or to this computer's portable music player, remove it now and restart.

  I tried to start in safe mode, safe mode with command prompt and last know good configuration but still no joy, so I eventually ran the recovery disc. Once it was finished, I was to square.

  Does anyone have an idea of what I can try next - other than to throw it out the nearest window.

  Thanks in advance.

  Hello

  Never heard talk of this error but sounds strange
  If I understood your first assignment; you were able to complete the installation of the OS from the recovery disc. Is this good?

  Well, in this case the HARD disk must be OK because the files were copied correctly

  I searched a bit in google and didn t have found a solution to 100%.
  Some have said that new OS install should solve this perhaps you could use clean up Windows Vista, Win XP disk

  You can also try to format the drive HARD integer first. Delete all partitions on the HARD drive, and then try again

  PS: You can check the HARD drive using the + Hitachi Drive Fitness Test. +
  Its free tool. You can find using google

• FF does not start after upgrading to version 27.0.1

  FF does not start after upgrading to version 27.0.1
  Crash ID: bp-2bc18734-d643-4843-a10f-fd6102140214

  Firefox 27.0.1 is too recent for me to know what unique issues it may have. I will message you a link to download the installer for Firefox 27.0 to see that the inversion or not the problem.

• Satellite A200 PSAEOE does not start after upgrading memory

  Hi, I am first time here.

  I bought a Toshiba A200 PSAE0E-03J02JDR with 2 GB of RAM. I bought a pair of ram Corsair (2 * 2 GB VS2GSDS667D2). The computer does not start after that I installed the memory. I have intel 945 chipset, which is capable of 4 GB (manual page 1-2). The bios version is 1.8 2007.

  Can anyone help me, please.

  Post edited by: Marian ovidiu

  Hello

  The A200 series supports different chipsets;
  Intel 945 PM
  Intel 945GM
  Intel 943GML

  As far as I know your laptop supports the * 943GML * Intel chipset and the chipset supports 2 GB RAM max.
  Take a look at your laptop s user manual * Page 18.*

  Summer: 4 GB of RAM are not possible, and therefore your laptop does not start.

• Satellite P200D-130 does not start after upgrading RAM

  Hi, I just upgraded the RAM on my P200D 130 but it does not start after that.
  I removed the 2 Hynix 1 GB PC2-5200 and put in 2 SO Kingston DDR2 2 GB PC667 (should be the same as PC2-5200).
  Post-market nothing happens, light power control is turned on, I him stays CD drive but screen black, no beeps.

  I put one of the 1 GB modules, it starts normally, then I tried a 1 GB into the lower slot module and a 2 GB module in the top slot and it works.
  I tried a single 2 GB module in each slot, even in the form of 2 2 GB modules.

  What could be the reason, better: what would be the solution to ensure that the modules of 2 x 2 GB to work?

  Thanks in advance,

  Michael

  Hello!

  I think that both modules are not compatible to the laptop.
  Normally you can upgrade your laptop to 4 GB. Look in the user manual.

  The RAM, you should bring the computer dealer and request a new one. More buy modules with the same specifications and dimensions. Try buying RAM with the same specs as before.

  Good bye

• Re: Smoker L30-10 X PSL33E does not start after upgrading RAM

  Hello

  I have a problem with my laptop.
  It has 1024 MB of RAM (2 x 512), but it wasn't enough, so I decided to update to 2048 MB (2 x 1024).

  I bought two modules and my computer does not start after changing them.
  It was only a screen black (same BIOS has not started). I tried another combination of installation of memory modules RAM.
  2 x 1024 - did not work
  1 x 1024 - did not work
  1 x 1024 + 1 x 512 - working but not properly.

  BIOS find that I only 896 MB (1024-128 for the video card)
  I said OK. Let's see what will show windows. He was also 896 MB.
  I launched CPU - Z and it shows that the total size of memory is 1536 MB (medium detect both modules).
  I found that CPU - Z detect 1 module 1 024 MB and 512 MB secondary, but the BIOS detect only 1024 MB 1536. How is that possible?

  I have fought, is that my BIOS is old, then I update the toshiba Web site form most recent version, but the problem persists.
  Please someboy help me and tell what to do.

  PS. the Modules are new and work correctly.
  They have been tested.

  Hello

  Have you used two identical RAM modules?

  What kind of modules did you use?

  In my view, that the problem is related to the new, inserted modules.
  There must be something wrong with the modules or modules are not completely compatible if the laptop can not boot after installation.

  According to a few pages of the book handles the DDR2 533 MHz (PC2-4200) 200-PIN SODIMM modules.

  Did you use these modules?