Satellite Pro M70 - wireless has stopped working

I have a Satellite Pro M70 and the wireless stopped working. The yellow light lights up for a few seconds for the machine to wake up but then turns off. I rebooted several times, but that did not help. In your reply please clarify abbreviations - thank you!

Post edited by: boston1

Hello!

Have you tried to update the driver WLAN? You can find it on the Toshiba site or portal driver WLAN:
http://APS2.toshiba-tro.de/WLAN/

Have you checked for yellow exclamation marks Device Manager?

Check if the laptop WLAN switch lights up and I can disable/enable WLAN with FN + F9 on my Satellite phone.
Check it!

Good bye

Tags: Toshiba

Similar Questions

  • Satellite Pro M70 - cooling fan stopped working

    Hello

    I have a laptop M70, I have recently identified as not very hot when in use. I have now identified that the fan has stopped working.

    Any ideas how I can get this fan, so I give it a clean and check that the connected fan isn't loose etc.?

    Thank you

    Are you sure that your cooling module has stopped working 100%?
    Maybe the cooling module is ok but cannot run with maximum performance and can not cool the CPU correctly because of the dust and debris inside the laptop?
    What do you think of this theory?

    I can tell you that I read a lot of stories and gossip on overheating problems and be more honest to these issues could be solved by cleaning fans.

    I clean my cooling fans from time to time with a jet of compressed air.
    These sprays are professional tools and can be purchased in most dealers specialized computers.

    But if the fan has stopped working and then a jet of compressed air will not help you.
    In this case, a technician must check the laptop.

    Maybe the laptop must completely disassemble to remove and replace the defective part.
    This procedure is really tricky and must be performed by a technician for laptop.

    Good luck buddy

  • Satellite Pro A300 - 2C5 has stopped working

    Hello

    I have a problem with my Toshiba Pro A300 - 2C5.
    It stopped working today.

    I have paid a top tea but removed is as fast as possible but a little water got inside my laptop.
    He worked for a while, I turned off and it works again an hour later, but unfortunately it has stopped working.

    When I try to turn it on, the syptoms are as follows:
    -the only light that shines is a power indicator light
    -l' screen does not work at all (it stays black and went offshore)
    -fan works
    -It seems hard disk does not work if Windows does not start
    -the keyboard does not work, when I hit tke keys nothing happenes, I tested the Caps Lock key, but not flashing
    -computer does not read my camera memory card

    What shoul I do to get it working again? :(
    Any help appreciated.

    K.

    Hello

    The anomaly can be related to different laptop parts in the worst case the liquid spill damage the motherboard and you will need to replace the part.
    In the best cases, it could be a RAM error as it happens to one of my friends.
    He spilled coke on the keyboard and after awhile the laptop could not turn on.
    We checked memory sharp and replaced both modules with new RAM modules and this fixed the problem

    You can try this also maybe it helps if all other parts should be checked by a technician of the ASP.

  • Satellite Pro 6100: fan has stopped working

    I recently decided to copy out all my data from my laptop and it just stopped. It was very very hot, and the hard drive has not worked since. I put a new disc in and installed the software but it heats up really fast. My question is this all a result of the fan (I can't hear more) stop and is it possible to buy a fan and install it myself - I've already cracked it open and got down to the fan and it looks like dust-free. I am pretty handy and want to do it myself.

    If the fan is originally where can I buy a replacement?

    Hello

    This looks like a laptop computer could overheat.
    If you can't hear the fan or cooling module is bad or there is something wrong with the motherboard.

    In my opinion, the cooling module must be checked and possibly replaced.
    All parts and devices can be controlled from the maintainer authorized Toshiba in your country.

    Just call the guys and order the compatible part or if you have no experience, ask the guy to help him. I think that you should not replace anything by yourself. It may be damaged anything else. The technicians have more experience and can locate and solve the problem much faster.

    Good luck

  • On Satellite Pro P300 touchpad has stopped working

    Hello.

    I have a Satellite Pro P300 equipped of Vista and the scrolling feature broke on my machane too.
    I also lost the touchpad icon in my taskbar and function to configure the touchpad.

    I've uninstalled and reinstalled the drivers, nothing works.

    If I had more hair, I would probably be pulling it. Help, please.

    Thank you

    Hello

    What drivers you have reinstalled exactly? Normally, you can download all the drivers from the official website of Toshiba:
    http://EU.computers.Toshiba-Europe.com > support & downloads > download drivers

    Have you tested the scrolling feature using an external mouse?

  • Satellite A500 - 15N Wireless has stopped working

    I bought my A500-15N in last October and had no problems at all with wireless connectivity. Last night when I was surfing Internet it suddenly stopped working (literally between two pages on Wikipedia) and I can connect is no longer. When I try the troubleshooting option, I still see an error 'wireless capability is turned off. I not made any changes to my router or laptop, so I'm not sure what could be going wrong.

    Is the wireless adapter fuck and I need to get this replaced? I tried the combo FN + F8 but which does nothing either.

    Hey,.

    Is the WLAN card still listed in Device Manager correctly and have you tried another key FN if combination work?
    Usually the WLAN card can be disabled with the FN + F8 key combination you wrote

    In your case I would recommend updating the driver WLAN. You can download the latest driver WLAN here:
    http://APS2.toshiba-tro.de/WLAN/

  • Satellite Pro A300 Touchpad has stopped working

    As the title suggests.

    My laptop is a Satelltie Pro A300 2 4.

    The Touchpad is not responding,

    I tried FN F9 - nothing happens.
    I tried pressing the upper left corner of the Touchpad - nothing happens.
    I tried to go to the mouse control panel and looking for an enable bit Touchpad cannot find the mouse set.

    The operating system is Windows 7

    Hello

    Have you tried to install the driver for the touchpad?
    You can find the driver for the touchpad on Toshiba UE driver page.

    Extra tip: in some cases possible to enable and disable the touchpad in the BIOS.
    Please check this!

    By the way: is an external USB mouse attached to the laptop? If so, unplug it and try to use the touchpad

  • Re: Satellite L850/046 - keyboard has stopped working

    The laptop Toshiba Satellite L850/046 - keyboard has stopped working.
    Have restarted. In the box of charms, it seems ghost.

    Impossible to restore or reset as it asks password and keyboard does not work

    Hello Graham

    Sorry, but your problem is not easy to understand. After reading these two sentences, it is not easy to tell if there is a general problem with the keyboard or what.
    When you enter the BIOS settings can use keyboard to scroll through the options and tabs of the BIOS?

    Since when did you notice this problem?
    You have created a recovery media? If Yes, please try to use it and install original recovery image.

  • I bought acrobat 9 pro. It has stopped working, and I don't have the license number or serial number. How can I fix it?

    I bought acrobat 9 pro. It has stopped working, and I don't have the license number or serial number. How can I fix it?

    Hi Max,.

    Please visit the following link to get your serial number.

    https://helpx.Adobe.com/x-productkb/global/find-serial-number.html

    Concerning

    Sukrit diallo

  • Adobe first Pro CC2014 20141 has stopped working

    Capture.PNGWhenever I try to launch the program this message 'Adobe Premiere Pro CC 20141 has stopped working. A problem caused the blocking of the program works correctly. Windows will close the program and notify you if a solution is not available"I tried to uninstall and re install the program like 2 or 3 times already, can't find anything on the Internet can help me either. Please if you have any suggestions made me know.

    Here is a screenshot.

    Hello

    Can you please check if you have Service Pack 1 installed for Windows or not. My guess is that it is the first cause of crash.

    Concerning

    Dorin

  • Satellite T130: integrated webcam has stopped working

    Hi, I have the same problem of the bellows of the question, as I looked around and I was not able to find the answer I need.
    I have a Satellite T130 and, suddenly, the integrated webcam has stopped working properly. A blue light is on, but there is no picture. What can I do?
    Thank you

    Hi mate

    I have the same problem, sometimes using my U400.
    This happens if the room is dark for the camera.
    If something like this happens to you that I recommend that you keep your finger in front of the webcam for a short period.
    After that, the image of the webcam should come back again in my case it worked.

  • Satellite L770 - ethernet adapter has stopped working

    Hello
    I have three laptops all connectable to my home hub, but I seem to have serious problems with the latest model, L770-13D. The signal strength has never been as good as the older models, and most recently the Ethernet adapter has stopped working. I have updated drivers on the two adapters, but it did make a difference. I recently updated my connection and I wonder if the Ethernet adapter is not configured correctly because it was working fine before the upgrade.

    I also tried almost all the tests I can do - Toshiba config doctor returned a FAILURE on the verification of the material that I did, but the device manager says that the two network cards work OK. Also, troubleshooting reports wireless adapter that it "can be a problem", the evidence seems to be directed towards a hardware problem with this laptop.

    Any thoughts?

    Have you noticed this Ethernet problem on the first day? Otherwise, I recommend you to reinstall the OS using original recovery image and test once more with the factory settings. Recovery image contains the drivers right and tested. It is also configured to be used immediately after the first start, so it shouldn't be a problem.

    Have you ever done this?

  • Satellite A305-S6825: WLan has stopped working

    I'm in the United States. (I posted this message earlier)

    #1-I just bought Toshiba notebook a month or two ago with Vista Premium SP1.
    A day ago when I turned on the laptop, I got a notice to the effect:

    Windows Wireless Lan 802.11 Extensibility infrastructure has stopped working.

    -> Are looking for a solution later (recommended) the next time that you start the system
    -> Closed

    Those who were only two choices. I think I clicked on the first "search for a solution later.
    When I turned on laptop today, I got the same message.

    Anyone know what could be wrong with this new laptop?
    I use the wireless to enter IE7 and type your message.

    My husband and I are elderly and not too familiar with computers or computer language so if anyone has an answer, please make it simple enough for us to understand.

    We hope that this new laptop is not already broken.
    We cannot afford to buy another computer or have it repaired.

    #2-we tried to send questions by e-mail to MS, but they asked the PID. We looked in Control Panel and system (I think) and typed in the PID of there (OEM number), but it would not recognize MS.

    Can someone please help?
    Thank you very much.
    Alice

    PS: We have the DSL cable attached to our desktop (modem/router) and use this Toshiba laptop with modem/router of this office to get online (don't know if that is the correct terminology that someone else connected DSL, etc.).

    Hello Bob

    I agree with Kody and I think also there is a software problem or the WIFI network is not properly enabled. I use the European model of laptop, but I don't think that there is some difference of laptop models to the United States.

    If you want to use the WLAN, it must be enabled correctly. At first make sure that the WLAN switch is placed in position ON. The WLAN led should be on. After doing this using FN + F8 key combination to activate the wireless network card. When you press the FN key and keep down. Maps flash in high must be indicated. Always keep the button FN, but press F8 and select Wi - Fi ON.

    So now the wireless network card must be activated, and you should also be able to connect to your WLAN.
    If the problem persists, you can try to roll back the OS to an earlier time (when the network WIFI works well). To do this, you must start System Restore tool. Choose different restore point and to the next day when you think about the WIFI worked well.

    Sorry, but for now I have a better idea because I don't want to confuse you more than necessary.

    Have a good day and I hope that WIFI works well again.

  • Satellite U300-130 - TosBtMng has stopped working after installing Nokia PC Suite

    I have the same problem too... with Toshiba Satellite U300-130.

    Bluetooth worked well enough before I installed the Nokia PC Suite for my mobile on my PC (new version 7.1.26.0 Web site).

    To be correct, as a first step, I even managed to maintain a connection between the PC and the Nokia Bluetooth and ran the synchronization of the contacts. I tried several times, but each time synchronization run ended with the message "PC couldn't get response from your Nokia.

    After the reboot, my PC went crazy and started broadcasting the message "TosBtMng has stopped working" and it restarted every time that I ask him to close.

    Installation of the new version of BT Stack (6.40) does not resolve this error.

    Help, please

    I also use Toshiba Satellite, I use this [suite Nokia pc | http://www.softsea.com/review/Nokia-PC-Suite.html] version

  • P50 win 10 Pro - footprints digital has stopped working

    Hi all

    I just got my P50 (20EQS00600, M1000M, i7-6700HQ, 16 GB of RAM, 512 GB SSD) about a week ago and I quite like it. However, there is one thing that drives me crazy: after that I upgraded to Win 7 Pro 64 bit for win 10 Pro, the fingerprint feature has stopped working. This issue seems to be related to those reported in these two threads for the P70, but at the same time appears sufficiently different to warrant a new post:

    https://forums.Lenovo.com/T5/ThinkPad-P-and-W-series-mobile/P70-fingerprint-software-issue/m-p/22517...

    https://forums.Lenovo.com/T5/ThinkPad-P-and-W-series-mobile/fingerprint-and-sound-problems-P70/TD-p/...

    So, here is what I did:

    (1) I correctly installed Win 10 w/o retaining data/settings from the previous installation of Windows 7; I even reformatted the SSD drive.

    (2) for the initial installation, was asked by Windows Hello register prints I've done.

    (3) fingerprint worked during the first connection, but then disappeared as if by magic. Hello Windows is no longer appears as a connection option in the control panel of Win.

    (4) I found in Device Manager the Synaptics WBDI reported the following problem: "this device cannot start. (Code 10) ".

    (5) repeated uninstall and reinstall drivers are without success. I tried both have Win a driver and manual to install the drivers I downloaded from Lenovo page.

    (6) when I uninstalled the drivers and then wiped the fingerprints stored in the BIOS, I was again able to register fingerprints with Windows Hello. However, this time the fingerprints were not yet registered in Windows, and I had to cancel the procedure. Immediately after, the Synaptics driver stopped working, cf. 4).

    I am at a loss what to do. Strange thing is that I ran Win 7 for about a week, and the fingerprint reader worked fine all the time. (Due to the scaling of the questions on my 4 k screen, I bit the bullet and went to win 10, in case you're wondering.)

    So everyone out there has the same problem, does anyone have a solution?

    Thank you in advance and the best,

    A


Maybe you are looking for

  • Press F10, F11, F12 do not sound

    Hey guys! A few days ago. When I press F10, F11, F12 keys, increase or decrease the volume remains active. but they do not have a "pum" noise when changing volume levels. And there is no startup chime well I tried resetting the PRAM and SMC. Can some

  • Qosmio E10: dead hard drive - message no. IDE DISK

    Hello Last night, my HDD Cree very hard and is dead now. I get the message of DISK IDE NO.Obviously, I need to replace the hard drive.Can someone please tell me how and where I can buy one. At least 80 Meg or more. Cannot find anything on the web sit

  • "No service/search...". "on the Iphone 6 64 Gb

    My iPhone 6-64 GB worked fine everywhere for about 6 months, I have updated to IOS 9.2.1 a day and no service/message 'search' has appeared on the screen and I can't use it to make and receive phone calls. I did: -Restored to factory with IOS 9.2.1 S

  • HP Pavilion Sleekbook 15 with SSD

    Hi I have a Sleekbook and I tried to change the hard drive for an SSD in Windows 8. Is this possible? I noticed that the bios is enough locked so there is no AHCI setting. An SSD will work a good read / write speeds? or should I consider anything els

  • Updates will not install, error 646

    Cannot install updates.