Satellite Pro - Win7 - Msg does not

Similar Questions

• Satellite Pro L50 - A does not illuminate

  Hello

  I took a few steps on this forum but no luck so far...

  My L50 - A Satellite Pro was working fine up until yesterday, but today, only it just won't turn on. A small orange led light appears when I connect to the power cable...

  That's what I've done so far-

  1 power cable removed
  2. using a needle, pressed force shutdown (stop) at the bottom for 10-12 seconds
  3. then I pressed the start/power button on the front for 60 to 70 seconds
  4. I have connected the feeder and then to new press button start / stop at the front for 60 to 70 seconds

  Yet the laptop does not start!

  any suggestions?

  Thank you

  Hmmmmmm... It is not easy to say what the problem is here.
  Have you used your computer laptop usual ot, you might update something?
  In general, there are steps that you did which could be responsible for your problem?

• Satellite Pro M10 PS630E does not start after upgrading CPU

  I tried to install a new processor for my Toshiba Satellite Pro M10-PS630E.
  He initially has a 1500, I tried to put a 1766.

  I follow the maintenance manual, later the computer change is not star upward.
  When I connet to power it show that the luminous power of orange/amber color and make 5 flashes, then 3 and then restart blinking.

  My question is "is it posible to do a reset of the bios parametrers" or "reset the CMOS?
  Is it possible to get it working again.

  Hello

  The flashing light means that it has detected a hardware problem on the motherboard!
  Perhaps you have used a wrong CPU and is not compatible.

  Perhaps the BIOS does not support this processor and therefore this flashing error code appears.

  What say you can't update the BIOS! First of all, that's not possible since only focused on the victory of BIOS is available for download. You must run the Windows operating system to update the BIOS.
  Secondly the update of the BIOS won't help you with this problem!

  You must use a CPU that is fully compatible!

  Welcome them

• Satellite Pro U300 OS does not recognize PS/2 Port TouchPad

  I have a similar problem.

  My system doesn't recognize that the PS/2 Port TouchPad exists on my Satellite Pro U300. He acknowledges that it no longer works but when I go to Control Panel then mouse it does not appear in the list of devices.

  Help!

  Hello

  I m do not know what problem describe you exactly.
  Do you mean that your notebook computer touchpad no longer works, or did you mean the USB mouse?

  If you mean touchpad, so you should try to reinstall the driver for the touchpad.
  The European driver Toshiba page provides Synaptics touchpad drivers series Pro U300 for Win XP and Vista.
  But generally the operating system should automatically recognize the touchpad and touchpad should work even using the common internal Windows driver.

• Satellite Pro 6100 Modem does not - No Dial Tone

  Hello

  I'm in terrible trouble. I have a big meeting Friday and discovered that the internal modem on my Satellite Pro 6100 does not work. I downloaded the drivers of software Modem since the support site, and the installation seemed to go OK. There are no conflicts listed in the Device Manager, and when I query the modem to in the properties of the modem (from the control panel), it seems question OK too, but...

  HE DIDN'T THERE WAS NO DIAL TONE!

  I don't know that it is connected to my phone OK. Instead of a tone, I hear a loud hum, with a series of clicks. I can't hear being composed either DTMF tones, even when I disable "wait for dial tone. This behavior is the same if the modem is connected to the phone line.

  I have a big rally Friday and will need this modem to work... any help would be much appreciated...

  Thank you

  Matt.

  Hello
  that doesn't sound so good!

  The measure where I read that your ad you´ve checked your system almost all.

  Right on the thing, have you installed a firewall or other programs to check system that denied access to the modem?

  It is also ok, you should let check your laptop on a faulty Modem.

  Good bye

• Satellite Pro C660D - screen does not turn

  I just got my Satellite Pro C660D back from repair (for a faulty fan), but the screen does not light when I start the laptop.

  She lights up on the front (and I can rotate the block number power sp that the keyboard works).
  Any ideas?

  I agree, I mean the laptop should work just fine after it has been fixed by ASP so I think that something was not right here and the technician must check this!

• Satellite Pro A100-080 does not start - stays dark after 3 beeps

  Hello
  After a week off, the Toshiba Satellite Pro A100-080 (PSAASE-00G004GR, 4 GB RAM) of my kids start not anymore.
  When turn on/off the system, he * will beep 3 times * (one long, two short beeps), the HDisk light flashes 'blue' and then nothing more. A/c and battery power LED are 'blue', which seem to be OK status.
  No other useful help, as the screen remains dark.

  We had upgraded to 4 GB MEM (Kingston) a year ago and I already tried the old used 1 GB (included with purchase) or the replacement of 2 x 1 GB since December 2007, but equal status with these modules. This is not
  a defect of memory.

  I hope that this is not the motherboard, probably only the NVIDIA GeForce Go 7600 graphics included adapter?
  Does anyone have an idea what could be the problem?

  Thx for a short help.

  Hello

  Generally this type of beep codes are hardware related or with other words, hardware is defective. So I think it's a hardware problem and an ASP must check your laptop computer to identify the cause of this.

  On the Toshiba site, you will find a list of aspic:
  http://EU.computers.Toshiba-Europe.com > support & downloads > find an authorized service provider

• Satellite Pro L300 - touchpad does not work

  Hi all that I need help urgent because it drives me crazy. First of all, I use XP PRO. My laptop is fairly new, only around the age of 4 months, I had no problem with it at all. I formatted my laptop yesterday and reinstalled all the drivers that I downloaded here:

  http://www.ISD.Toshiba.com.au

  and everything works fine except the touchpad. I have already installed shared, utilitarian toggle the touchpad Module and I have the latest BIOS installed and reset all default settings and I made sure that the touchpad is enabled in the BIOS, but also pressing FN + F9 to enable during Windows.

  I installed the latest touchpad driver Synpatics I downloaded from the homepage of Synaptics. But for some reason any, that it does not work, I don't know what is the problem here. My touchpad worked before I formatted my laptop, it worked fine and has never had any problems. Will you please tell me what is wrong because I need to use my touchpad sometimes as well, so I can't use a mouse all the time.

  Hello

  > I installed the latest Synaptics touchpad driver that I downloaded from the home page of Synaptics
  I think that you question refers simply to the driver for the touchpad that is missing or incorrect.
  I put t know how it works on Toshiba notebook Australian, but the Toshiba European Satellite Pro L300 units needs touchpad different drivers. some use the Toshiba touchpad driver and some units need a driver for the Synaptics touchpad.

  In your case, I recommend this controlled again.

  By the way; My touchpad is always disabled so that en external mouse is connected.
  It is parameters that control it. Please check in your touchpad properties too!

• Satellite Pro M70-113 does not start up - it hangs at the logo screen

  Hello

  I have a toshiba satellite pro m70-113.

  Sometimes when my laptop turns off mode standby automatically, due to inactivity and then if I press a key on the keyboard to wake up nothing happens and I have no other choice but to it stop completely by pressing the button for 5 seconds.
  But when I restart it works well, that is to say, it starts very well.

  But today, when it is in a similar situation, I restarted the laptop, the screen move after the logo screen toshiba. I have the power on several times, but without success. It crashes just on screen toshiba logo.

  After a few restart I pressed ESC while restarting and the toshiba logo changed to the texts POST bios screen.
  And I found that the text will not go forward after having reached:
  Find disk 0:
  Maybe default feel HDD initialization...
  The captured image is here:
  http://img144.imageshack.us/img144/9986/image007sp2.jpg

  Note: this is a capture when, I don't know how the system has just begun works very well and can be seen that the HARD drive is detected normally this time. While the earlier version, it will not proceed after having reached "Found Disk 0:

  So, the problem is that at the time of the problem, the hard drive was not read / initialized or something like that.

  And I remember that when I tried to reboot my laptop and it did not work. It was running on battery and when I switched power supply that worked.

  So it is a problem that has been fixed in a bet to update BIOS, but for another laptop (see laufendspass post) his link on this forum is here:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=13143&MessageID=48143

  And my current bios version is 1.1 and an update is available for v1.30... (But I have not yet updated)

  Another problem I had met some time was same this post mentions to be corrected during the update of the bios.
  i.e. "corrected: a computer that is turned on to State power and running on battery power, may crash if the user is connected to the AC adapter while it is start.»

  So, for this, all mean that these problems can be solved by an update of the bios v1.30 which is available for my Satellite m70-113?

  Please answer.

  Hi Ashish,

  The fact that the initial POST process cannot access your hard disk suggests you that there is a possible problem with the drive, maybe he is not in place correctly when power is applied to it. The contents of the disc should be OK, then I suggest you take a good backup of your system (or at least your personal data) If you manage to get your notebook to boot successfully.

  I do not think that an update of the BIOS will affect any on that since the problem does not seem to have a certain 'trigger', and if the BIOS cannot access the hard disk then no matter what version of BIOS you are using.

  Kind regards

• Satellite Pro M10 - infrared does not work properly

  Hello

  I have a Satellite Pro M10 and my infrared does not work. I downloaded the zip file with the drivers from this site. Then, I uninstalled and reinstalled, but it always happens in the Device Manager under "unknown - SMC IrCC - Fast Port infrared (IR Module: HP). (with an exclamation point). When I look at the properties it says under device status:

  This device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

  Click Troubleshoot to start the troubleshooter for this device.

  However, under Driver Details is said:
  C:\windows\system32\DRIVERS\smcirda.sys

  I extracted the zip file in my home directory of c:\downloads\infrared.
  whatever I do, it does not now. It worked when I bought it, but I have too many things on the system for a new installation. Which brings me to another question. Is it possible to re - install windows without losing all your data, etc.? I did it with other systems (95,98) Windows. But it seems that the Toshiba recovery disc means any wiping.

  Thanks in advance for any help.
  Chris

  Hello

  If your HARD disk contains two partitions and you have saved the data on a second you can reinstall the operating system on the first partition using recovery DVDs.

• Satellite Pro 4270 - USB does not work

  Hello.

  I had this problem for a while, and I was wondering if anyone had any suggestions to solve this problem.

  I have more or less of work Satellite Pro 4270 (4200 Series) computer laptop with XP on it.

  The USB port does not work. I don't know why it does not work. I tried to replace the USB module on the motherboard that has not worked. I've updated the BIOS to the latest version, has not functioned. Removed and reinstalled the drivers in XP, not worked. I'm out of ideas.

  IrDA works very well.

  Some suggestions please. Thank you

  Hello!

  I understand, were you solder the module USB motherboard and then solder another module?

  I mean, what have you done with the module USB, replacing? Sorry, I don't remember exactly how the USB module is connected to my mobo SP4270 seen last about the half a year ago... If the welding, I don't wonder the problem... but if not, there may be a solution...

  Best regards

  Pete v.

• Satellite Pro P300-1AY does not see wireless networks

  I have a Satellite Pro P300-1AY and the unit does not see wireless networks.
  I replaced my card and it does not solve the issue.

  I set up another type of card and those who work well, it is only when I get an Intel 5100 (512AN_MMW) the unit does not see any network.

  I use win XP. Any idea?

  Hello

  You have the latest version of the BIOS?
  If this isn't the case, then you should first update the BIOS!

  The latest version of the BIOS is on the European driver Toshiba page and it can be modified running Windows OS.
  As far as I know, you must use 2.5 or later version BIOS.

  Check it!

• "SHIFT" on the Satellite Pro C660 key does not work

  G ' Day,.

  I have a little problem with my laptop Toshiba Satellite Pro C660.
  Unfortunately I had to remove the keyboard and thus dislodged the
  fragile plug to connect to the computer.

  The 'Shift' key refused to work since. All other keys work as usual.
  The only problem is the 'Shift' button does not.
  I tried to gently move the plug but made no difference so now have to
  Use a USB keyboard.

  Can you please help with suggestions for this problem?
  Thank you for your time.

  See you soon,.
  Sunrap.

  I really put t know what you think when you know that there is no connection for each unique key, but for the entire keyboard.

  To be honest I ve changed keyboard several times but never noticed this problem.
  Are the two SHIFT keys off function?

• Satellite Pro P100 - sound does not when I try to use Gentoo

  Hi guys,.

  I have a Satellite Pro P100 (model: PSPA4E). I tried to get Gentoo working on it, but can not get the sound to work. In my attempts to get the operation, I've upgraded to v3.5 (some recommended forum) Bios. The sound still does not work.

  Has anyone got the same laptop and managed to get the sound to work? Or can someone advise me.

  Thank you.

  Hello

  How you try to do a little sound? With alsa? Usually you must first compile your kernel for alsa soundcard and support you as a module, then alsa can load this module when you run alsaconf user-space to configure your sound card.

  I had gentoo on my server before migrating to ubuntu server edition and I find after working with several systems of derivatives, and bsd linux gentoo is too complicated, especially regarding him emerge and trees.
  I tried to install software that was not in the portage tree correctly and the path is too long for some external incoming traffic software.
  Then based on debian.

  Welcome them

• Satellite Pro A200 - system does not boot

  Hello

  wondering if someone could help?
  My Satellite Pro A200 with windows XP does not start. It starts with the Toshiba screen.
  Then goes to a screen black with text where it says "PXEE61 media test failure - check cable" (I have no cable) then said out of PXErom; moves to the next screen, which lists the options: safe mode; safe mode with networking; safe mode with prompt local; Last Configeration well-known; Start windows normally.

  Which have been tried and results in loading from page turns on for about 20 seconds, then just to abandon and trying all the whole process again (before flashing a blue screen) Windows.

  Nothing seems to work - tried to take the battery on a... number oftimes and the power cable, but nothing helps.
  It's already happened, but after a few false starts gets going - but this time he just don't come out it. I could not take others where locally, but I would prefer not to because I live in Spain and need the laptop as soon as possible and do not know, I want to leave it in some otherwise are hands to the risk of wipe them the hard drive.

  So, I would be very grateful for any help as soon as possible and I fear tech short hand maybe having to explain.

  Thanks a lot, a lot.

  Hello

  I think the problem is that the operating system is not found on the HARD drive.

  The test failure PXEE61 media - check the cable appears especially if the laptop tries to boot from LAN.

  Why the laptop is trying to boot from the local network?

  Well,.

  -option may be the LAN was chosen first in the boot order in the BIOS
  -Maybe the drive is defective and so the laptop is trying to boot from LAN
  -the MBR (master boot record) is may be defective

  I think you should take the Toshiba Recovery CD and need to format the HARD drive and needs to be reinstalled the operating system.
  This should help.

  If not, then the HARD drive could malfunction and should be replaced!