Satellite R15-829: keyboard & mouse will not work on advanced port replicator 3

Similar Questions

• Usb keyboard/mouse do not work on h8-1214

  I was upgrading the graphics cards on my h8-1214 and I uninstalled the AMD catalyst control center and restarted the pc. at the start, I noticed that the keyboard and mouse do not work. I looked around on the internet with my laptop computer and learned that AMD drivers have a bug that causes the uninstall process to remove usb and all display drivers drivers. any way to fix this or I do a full system restore? When I bought the pc, it came not with a system restore disk.

  USB drivers should auto install if they have been removed, but just in case, here are the normal USB driver .  Here are the drivers USB 3.0

  Just for reference, there are restore discs but you had to go, or you can order from HP.

• Satellite 5200 802: keyboard and touchpad not working

  Hello world.

  I was hoping that someone could help me with a problem I have with my 5200-802 Satellite. The keyboard not work DVRs, although it shows in Device Manager and report it as works fine. I updated the BIOS and tried a bunch other things basic suggestions would be greatly appreciated.

  It may be useful to mention that I also can't my touchpad driver to register.

  Thank you very much.

  Hello

  Do you have an error message, or have you signs of bed on the screen?
  You can use the keyboard to access the BIOS?
  If yes then the keyboard has been recognized and works!

  If you can not use the keyboard running OS then I recommend to remove the keyboard device in Device Manager and restart the laptop.
  The keyboard should be recognized again after new OS reboot.

  But I think that you will not be able to access the BIOS.
  Due to the fact that the touchpad works too, I imagine that the hardware is defective or there is no connection with the motherboard. Maybe a lose cable

  Maybe you should check this. But note; If you have no experience with laptop technicians. Good bye

• I made the mistake of disabling all my USB ports in Device Manager! Keyboard & mouse do not work. I need to restore the Sys - HELP!

  I made the mistake to disable all my USB ports in the device (Windows XP Home Edition) my mouse Manager and the keyboard works not because they are connected through USB ports. I need to find a way to get to the system restore through the Mode without failure or normal startup. Can someone please help!

  Hi PaulCanik,

  • Do you use your laptop or desktop computer?

  Check if keyboard works in basic input/output system (BIOS), if it works, then you will need to enable USB port from there.

  You will need to contact the manufacturer of the computer to aid in the basic input/output system (BIOS).

  If this does not help then you need to connect PS\2 mouse and activate later all USB ports on the computer.

  Important: Change (CMOS) BIOS/complementary metal oxide semiconductor settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

• Clicks of the mouse will not work on the browser - suggestions?

  Following an update of Firefox last year, I can't get the mouse clicks to work on the browser. Is not serious if he left or right buttons. Links and radio buttons get highlighted when you move the mouse over the links or buttons, but they do not work when you click on it. They work on other browsers (Explorer and Chrome) but is no longer on Firefox. I use it on a Sony Vaio laptop running Windows 7

  The reset Firefox feature can solve a lot of problems in restaurant Firefox to its factory default condition while saving your vital information.
  Note: This will make you lose all the Extensions, open Web sites and preferences.

  To reset Firefox, perform the following steps:

  1. Go to Firefox > help > troubleshooting information.
  2. Click on the button 'Reset Firefox'.
  3. Firefox will close and reset. After Firefox is finished, it will display a window with the imported information. Click Finish.
  4. Firefox opens with all the default settings applied.

  Information can be found in the article Firefox Refresh - reset the settings and Add-ons .

  This solve your problems? Please report to us!

• Satellite Pro L850 - keyboard / touchpad does not work

  Hi all!
  I just bought new Satellite Pro L850 with windows 7 64 bit on a recovery partition.
  I have a big problem of internal cause keybord does not work under windows. In the bios, I can do anything I want. But the first configuration of windows (I can not deal with same user name and the name of the computer), keyboard does not work. I own windows version (with programs toschiba - recovery partition).

  It seems that this is not a cause of hardware under the work of bios keybord problem.

  Extra I have updated the bios last version 6.50, but not noticed any changes.

  Please help me with this question, cause I don't have any idea what to do now.

  Good day and w8 for answers

  PCZ

  PS. external keybord on usb work!

  Post edited by: pcz

  The whole story seems incredible. Keyboard and new laptop does not work?
  Install the check and image recovery again if the situation is the same. If the problem persists contact your local dealer, explain the situation and ask for Exchange.

• Satellite A200 28H: F6 floppy will not work when installing XP

  Hello

  I am trying to install Windows XP pro on my new laptop (Satellite A200 28 H), and since it needs driver SATA, I downloaded the driver suitable for my laptop (Satellite A200 28 H), put it on a floppy disk for use with a USB floppy drive (which works fine), press "F6" when appropriate and everything... But it simply doesn't. I had training as a technician for a few years, so even thouh that is no longer my work and I might be a little rusty, I think I still know at least a little what I do... Well, apparently I'm more image than I thought!

  I've tried several things, and this is what I get:

  * If I don't use all the disks, Windows XP will not find the hard drive. Which was intended, no problems here, don't except for the fact that it is completely useless for me :)

  * If I force the driver on the floppy disk, despite Windows tells me that is already a driver that can be used, then within 10 seconds I get a BSOD with the stop message 0x7B (found or inaccessible boot device).

  * If I use the floppy drive, but do not force the driver and listen instead of Windows ("oh, you already have a driver? ("OK, then, use and too bad that diskette"), I can actually finish the installation process. Windows will copy all the necessary files on the disk, it will even restart correctly after that and moved on. But when the installation is complete, the computer will restart, I'll see the loading for a second screen, and then, BSOD stop 0x7B again.

  I'm sure I downloaded the driver for my computer. In fact, I also tried a couple of bad drivers too, just to be safe (IE I use Intel Matrix for ICH8M, but I also tried the ICH7M to be sure), I tried with drivers downloaded from the Toshiba site, on the site of Intel and whatnot-other-website-for-newbies-or-powerusers, and I still have the same behavior as described above.

  I tried partitioning / formatting during installation, and I also tried leaving the file system intact. If I do the latter, the only difference is that I have offered 2 possible OS to boot from, the two being Windows XP and both failed miserably.

  It's probably worth mentioning that, if I use the recovery DVDs and start over and clean with Vista, I have no problem whatsoever, except for the loaded gazillion process during startup, the RAM already used half and applications useless hundred I don't give a darn on... And the fact that some applications that I need work just can not be installed on Vista.

  If anyone has any idea how to solve this problem, I would be very grateful!

  Hello

  The procedure, including the SATA drivers in Win XP using the external USB floppy drive is very easy.
  First you need to download the Storage Manager and having to put on the diskette.

  During the installation of Win XP you must press F6 for inclusion since the external floppy drive and follow the new instructions on the screen.

  _Note; _
  Very important is that your XP CD Win would contains SP2!
  Without SP2 a BSOD can appears and could break up of installation!

  Don t format or don t create all partitions after the installation of the SATA driver. It can erase the installed and included from HARD disk SATA driver.

  Last but not least some readers of external floppy drive are not supported. I read that some users had some problems with an external FDD drives they tested another drive and it worked finally

  Check the recommendations may indicate that it might be useful

  Good bye

• Satellite A100-062 - USB mouse does not work

  Hello

  I have a Satellite A100-062.

  I've never been able to get a USB mouse to work with her.
  The OS is Vista Home Premium, whenever I have plug in a USB mouse, the operating system detects a device has been connected to the USB port, but eventually the message material has not installed successfully.

  So I have to rely on the touchpad, the problem seems to be limited to mice only, I've successfully used a USB webcam without incident.
  I tried several USB mouse with the machine exclude a problem with my original mouse.

  Has anyone else had similar problems?

  Thank you

  > So I have to rely on the touchpad, the problem seems to be limited to the mouse only, I have successfully used a USB webcam without incident.
  Looks like a problem with the USB mouse and not with the laptop or with USB ports
  I would recommend testing different mouse and using the other.

• Keyboard & mouse does not work

  After several attempts, using the two P/s2 USB keyboard & mouse and keyboard & mouse I can't use my keyboard or mouse when log in to XP

  Thanks Charles

  Hello

  ·         Were there recent changes made on the computer before the show?

  We recommend to use a different mouse and keyboard, then check the result. If the problem persists, try the following steps.

  Method 1:

  Step 1:

  I suggest to boot into the BIOS and check if keyboard and mouse are getting detected.

   

  Warning of the BIOS:

  BIOS change / semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

   

  Step 2:

  I suggest to start in safe mode and check if you are facing a similar question.

  A description of the options to start in Windows XP Mode

  Method 2:

  Try to complete the restore of the system in safe mode and check if it helps.

  How to restore Windows XP to a previous state

  http://support.Microsoft.com/kb/306084

  Method 3:

  Also try to uninstall the mouse and keyboard from Device Manager drivers, restart the computer and let Windows install the drivers.

  How to manage devices in Windows XP

  http://support.Microsoft.com/kb/283658

  Method 4:

  Also try to run the Microsoft Fixit from following link:

  Hardware devices do not work or are not detected in Windows

  http://support.Microsoft.com/mats/hardware_device_problems/en-us

• My MS 5000 Mouse will not work on glass? Any solution?

  I just bought the mouse and found that, after I've cleaned my desk top in glass that lists the mouse is no longer on the screen.  Someone has the fix for this?

  The glass is transparent?  Usually, transparent glass will leave the 'light' mouse / "laser" to get completely through.  It is not reflected back to the sensor so that the mouse / pilots cannot see that it has been moved.  You may need a mouse pad.  As test, place a single sheet of paper and try the mouse.  If the mouse seems to work, then you will need the key.

• Satellite A7330 S75Dt - keyboard backlight does not work

  Hello

  recently I bought this laptop A7330 S75Dt with windows 8, and after 2 days, the backlight of the keyboard has exploded.
  The Fn + Z combination indicates it's on and it should work, but it's not.
  I don't need it but its irritating that it does not work. I hope someone can help me.

  Thank you
  Luk

  Go to the BIOS by pressing the F2 key while under tension.
  Then go to advanced-> configuration of the system and check if the lighting of the option is enabled.

• Portege R500: external monitor does not work with the Port Replicator Port 2 and DVI

  I have a Portege R500 running Vista with a slim Port Replicator II and digital monitor Viewsonic.
  I connected the monitor to the DVI port on the port replicator and got it to work OK.
  Press fn + F5 would switch between the computer screen and the external monitor.

  Then it stopped working, and I can't make it work at all. F5 recognizes just the laptop screen.

  If I connect an analog display, it is fine, and I can pass between the two screens without difficulty.

  The strangest thing is that, if I reboot when the Portege R500 is docked, the digital monitor begins by displaying the boot sequence, but then the signal is lost as soon as the screen stops the display of the progress (in low resolution) bar.

  I spent an hour on the phone to support Friday, and he made me nowhere.
  They finished by saying that he should never have worked! So what is the DVI port because then?

  Any ideas?

  David

  Connect your monitor directly to your laptop and see if it is recognized and you can go through FN + F5 between the two views.
  If it works, then connect with port replicator, and then try again.

  It's probably best if you reinstall display drivers. Maybe there are new too on the download page.

• Tecra M4: Cannot get com-port working on Advanced Port Replicator III

  Hi all

  I bought the advanced III PA3314E-1PRP port replicator but could not get work com-port.

  It does not get listed in my equipment manager.
  Anyone has an idea why not?

  Thank you very much in advance!

  See you soon

  Infinito

  I agree with Akuma
  (The name says it all) port replicator replicates the available ports on the laptop.
  If your laptop does not have this port, then you cannot use it with Port Replicator.

• The plug-and-play USB mouse will not work on Satellite A100

  Hello

  I have a laptop Satellite A100 laptop and when I try to install a plug and play mouse windows says it is not recognized - unknown device.

  Please help the mouse works.

  Thank you very much

  Hello Jayne

  It will be really interesting to know where you're trying to connect the USB mouse. Can you send description of mouse models please?

  As I know it is not necessary to install a driver for external USB mouse and mouse is usually recognized automatically. Please check if a driver installation is needed, and even request delivered must be preinstalled.

• Satellite A300 - a RAM module will not work

  Hello guys,.

  6-8 months ago, I had a terrible accident with my laptop, I spilled:(coffe là-dessus.) Initially it has worked very well, but after a few days I just couldn't start it. When I pressed the power button, 'satellite' logo turned on, I could hear the fan but the HARD drive would not start. Tryied to clean and finally he started to :)

  Then from time to time (each is approximately 40 days) it does not start and what I've found, is that the RAM slot near the motherboard has a problem. When I remove the RAM from the slot, it works very well (but with 2 GB instead of 3 GB). A few days later, I put the second RAM and reworked for the next 40 days. Even in this way, I was satisfied after what had happened (the accident of coffee).

  The problem is that the same thing happened about 1 month ago but still every time I insert the second RAM I get the black screen, fan works and nothing more (with 1 memory it still works). Is it possible that the slot 2 is now dead, after 6 months of a semi-travail condition? Do you know how to clean it? or do something else?

  I changed the 2 RAM in both slots and I'm sure that the work of two Ram.

  Thank you and I would appreciate your help as I am a student and I use a lot of Matlab (it takes forever with only 2 GB of RAM)

  Post edited by: creative1

  Hi creative1,.

  I think that it s not easy to say which is the main reason for this problem. Theoretically, it could be caused by the coffee that you reversed but it could also be another reason. In my view, that such a precise diagnosis can be done from an authorized service provider.

  The memory modules that you are using? Two of the ASP and pre-tested modules?

  Modules of RAM, you can test with special software of diagnosis than Memtest86. If the RAM modules are faulty, Memtest86 should acknowledge mistakes. It would be interesting to try.

  In the worst cases, the second location of memory is faulty. If the bars of memory work in the first place it seems to be the case :(