Satellite U400 - failed to create the recovery disk - bad DVD player?

Similar Questions

• Satellite C650 - failed to create the recovery disk - error 020150-20-00000000 code

  I hope this is the right place to post this, but I think I have the same problem with my Satellite C650. He keeps wasting DVDs by stopping and saying that it cannot read the file E:\ZZlmg\11544XSP.swm and gives an error code 020150-20-00000000. The file is located on the DVD. I use Verbatim DVD - R The Recovery Media Creator is trying to write the first disc and is at the point of check data. Can you think of another explanation for this error other than the cheap DVD option? Thank you

  Hello

  There are two explanations;
  Either the CD/DVD drive firmware is not up to date and contains no information about the drives used discs (CD or DVD) is not fully compatible.
  As you know this is happening and is not uncommon.

  So first check if a firmware update is available for your CD/DVD drive.
  The European driver of Toshiba page is the right place to look for that.
  More details you will find in detail if the firmware has been published for your ODD.

  If there is no update firmware of your CD/DVD drive, then you should test other discs

• Satellite A300-15 has failed to create the recovery disk

  I'm trying to create the recovery for the first time disk (portable purchased before 5 days) and stop just before the end, the creator:

  Cannot read the file.
  F:\06343XSP5. STORMWATER MANAGEMENT
  (Error code: 020150-20-00000000)

  What's not?

  I posted this already in another thread, but I can repeat it;

  I noticed that not all DVDs are compatible and sometimes it of not possible to burn the recovery due to the problem of DVD DVDs.
  I put t know what DVD discs you use, but I had a good experience with TDK DVD-R.

  So my advice is simple; Try different DVD from different manufacturers

• Failed to create the recovery disk - error code: 0E01B5-26-00037304

  Hello

  I bought the new laptop Satellite A300-1MC, but I was without recovery disc, so now I try to do disk recovery, but his show me then the following error:

  A power calibration area error
  and
  error code: 0E01B5 - 26-00037304

  I tried 5 times 4, and used a NEW disc, but still show me the above problem.
  Will thank you for answer you.

  Thank you
  Jan

  Use please TDK or Verbatim DVD-R media and I think everything will work OK.
  I created the recovery media on several laptops using these media. It works perfectly.

• Satellite R630-13D: failed to create the recovery disk

  I have a similar problem. I have a Satellite R630-13 t and tries to use the Toshiba recovery Media creator to create restoration 2 DVD discs.

  When you try to create the first disc, I get the following message:

  Cannot read the next file.
  E:\Boot\fonts\chs_boot.ttf
  (Error code: 020150-20-00000000).

  I get a similar message when you try to create the second. I tried four times. On my last attempt, I disabled the protection in real time on my virus checker (Windows Security Essentials) - I don't know how to close down completely, not sure you can. I also turned off wireless and bluetooth.

  I need to create these discs please. I use anti-scratch Philips DVD + RW 4.7 GB 120 Min 1-4 x speed discs.

  I know that someone else mentioned to try a different type of disc but I just bought these for this purpose and don't really want to buy more if I can help it. The disc type is certainly not a problem? When I look at the disc in the drive, they have files on them - even the file that the error message above says that he could not read.

  Thank you
  Ian

  I had similar experiences in the past and I can say that, after several tests using different types of media, I was able to create recovery discs using DVD-R only media.

  Hey two disks empty buddy aren't really expensive so don't waste your time here awaiting a solution and buy two or three empty DVD-R discs and create recovery media.
  Another tip: do not buy some cheap stuf but high quality TDK or Verbatim discs.

• Satellite P300-1CN - failed to create the recovery disk

  Hi, I tried to create the disks of backup for my new P300-1CN recovery, but I get a power calibration error (error code: 0E01B5-26-00037304) when the progress gets 50% on the first disc of "current" bar and 25% along the bar of"progress".

  I have now tried 3 times and exactly the same thing happens every time.

  I have the cable power in and power on a full battery.

  Any ideas?

  G.

  Hello!

  Have you tried the disks from different manufacturers? I prefer to use DVD - R Verbatim and TDK discs.
  Check it!

  Also on the site of Toshiba, I can find a few updates firmware for the CD/DVD drive. Check if you have such a unit and update the firmware.
  http://EU.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download drivers

  Good bye

• Failed to create the recovery disk - error: differences between the following files

  Hello, I am using the recovery disc option, but during the creation of the third disc, I get this error repeatedly (I tried to create 4 + times now, using the same type of discs that worked well with the first 2 discs). The full error message is:

  "differences between the following files. "Source path: path:F\ZZImg\09753XSP2.swm E\HDDrecovery\SWImg\0975XSP2.swm target (error code: 02016F-3 c-00000000)"

  How to solve this? I want to reformat my laptop, and the thought that it would be better to create these discs first. It is recommended to have the front discs I try to reformat? This error would prevent me to use the option 'restore factory settings' which is present by pressing the 0 key during the loading screen?

  (I'm not very technically capable, so I am greatly worried something bad).

  Any help would be greatly appreciated.

  Thank you.

  Have you tried using different disks from different manufacturers?
  To do this. I had similar problem and it was not entirely compatible disc-related.
  I use TDK R CD or DVD. They work great!

• Failed to create the recovery disk

  Hello.
  I'm trying to create a recovery CD but there was this error
  http://www.Tinypic.pl/rfjfibbhef1k
  help please

  Is there an option to create the USB stick recovery?
  If Yes, please test and send feedback.

• Envy of HP dv7 Notebook: failed to create the recovery disk.

  I have a HP ENVY Notebook dv7. When the computer was new, I tried to make a record of retrieving the value. When finished, I would check out (DVD - R) discs, I would get a message saying that disks has not written correctly. I tried three different packs records, always the same. Called HP Support and they went through the process with me, always the same failure. I was told not to worry if I still have the discs because of an accident, they would send them to me for free because they have a record. Now, I'll use this computer mostly on the internet and think I should have just in case records. Called HP and was not said no record, no free drives and it will cost a lot to make them help the discs. Is it possible to make records or put the info on a hard drive? I don't know if the computer thinks that I made a copy or not, because the copies, I thought I was doing were defective.

  @SAWANG ,

  I brought your question to the attention of a team within HP. They are likely to ask for information from you to get your information or product serial number. Please search for a private message from a contact HP identified. Also, remember not to publicly post information and series numbers.

  If you are not familiar with works of the function of the Forum, private messages

  this 'http://h30434.www3.hp.com/t5/First-Time-Here-Learn-How-to-Post-and-More/How-to-check-your-messages/td-p/3547355' postHYPERLINK instructions of a..

  http://h30434.www3.HP.com/T5/first-time-here-learn-how-to-post-and-more/how-to-check-your-messages/TD-p/3547355

• Satellite U500-17F - problem of calibration by trying to create the recovery disk

  I have exactly the same problem with the calibration by trying to create a recovery on Maxell DVD media disc + R I tried twice 2 DVD different each with the same error. Then I burned one of them on my desktop without any problem. When I tried an Emtec DVD + R support on the laptop it burned successfully.
  The laptop is Satellite U500-17F with Mat * un DVD-RAM UJ862AS. There is an incompatibility of Mat * one disc with Maxell DVD and must be fixed with a firmware update but Mat * one did not like.

  Hello

  I had a problem with a different disc from different manufacturers.
  Finally, I tested the TDK and Verbatim and could create the recovery disk using DVD R media!

  Test other brands!

• Satellite U205-S5034 - error when you try to create the recovery disks

  Hello world

  I have problems with the TOSHIBA recovery disk creator. When you try to create the recovery disks this error pops up:
  An unexpected error has occurred. Exit this application and start it again. (Error code: F1-0F00FE-00000002)

  The machine is a Satellite U205-S5034 under XP Pro SP3.

  Any help will be greatly appreciated. Thank you and have a nice day.

  DaveMatt44

  Hello

  What kind of DVD that you use to create a Toshiba Recovery disk? I have tried Verbatim DVD-R and TDK DVD-R and never had a problem with these discs. A friend tried DVD + R and he couldn t create a recovery disk. After he tried DVD-R and everything was fine but I do not know why this happened.
  So please try other discs.

  Also, check the Toshiba page for an update of the firmware of the CD/DVD drive. Maybe it will help you.

• Satellite Pro A300: How to create the recovery disk

  Hello
  I just bought a Satellite Pro A300 with Windows XP.
  I want to know how I can or if I need to create a recovery disk that will reset the machine to its original state.
  The information gives instuctions on how to proceed for the Vista machines, but not for XP.

  I know that I can recover from the hidden partition, but where this is not possible, I wish I could get CD or DVD.
  There is a recovery CD included product that says only: "MS Windows XP" so I guess that it does not include drivers or Toshiba Software?

  Any help appreciated,
  Thank you
  Mick

  Hello

  You have preinstalled software Toshiba TOSHIBA Recovery Disc Creator?

  Please check this box.
  Using the TOSHIBA Recovery Disc Creator you can create the recovery disk.

  But if your laptop was already pre-installed with Windows XP and then a Recovery CD or DVD must be included.

  Have you checked all of the items in the box?

• Create the recovery disk

  I have a pavilion dv6 Windows 7 and he needs a reconstruction. It doesn't have a D: partion but I wanted to play it safe and to create the recovery disk set in case there was a problem with the drive D. I bought some Maxell dvd + R disc but are not accepted by this utility.

  According to the utility I use either + r or - R disc, why did he not accept

  Thanks for any constructive help

  Get your product number by pressing Fn + ESC key or check the Service tag on the bottom, may be under the battery.

  Go to 'Support & drivers' at the top of this page. Enter your product number. After you enter the PN, click Next, then choose the software & Drivers.On the next page use the menu drop down to select your (probably Windows 7 64-bit) operating system. A list will fill with the drivers. Recovery media should be listed as an option to purchase, if you live in the United States / CA. usually around $17.

  If a recovery media is not listed, use the link that I posted above to get the phone number. Often if you support your software fails to create the set they send a free of charge.

• Satellite L - how to create a recovery disk?

  Hey,.

  I accidentally uninstalled the program "Recovery Disc Creator". But the folder with Win Vista Recovery disc information are still in my computer. Now, I want you help me in creating a recovery disk. My system is very unstable. So I want to re install. I hope you can help me.

  Sorry, but why did you uninstall the recovery disk creator?

  However, now you can not create the recovery disk because you have uninstalled the program to create the disc.

  The only way I know is you use HARD drive recovery option to reinstall your laptop. You can use it if you go to the advanced boot menu (F8 before Windows starts), choose repair my computer, and then select the Toshiba HDD Recovery feature.

  Normally you get this message if you start your laptop on first use:

  + Important INFORMATION +.
  + your system is equipped with a hard drive recovery system. If you need repair.
  + your computer in the restaurant to original factory State, you can do it directly.
  + HDD (press F8 when you start your computer, choose "Repair your computer" +)
  + and follow the instructions in the menu) or create a media drive bootable recovery to that end. +.

  + Toshiba recommends you create recovery disk medium uses the "Toshiba Recovery Disc Creator' to ensure the +.
  + Hat you are able to restore your computer to the State of origin, installed at the factory, even if your computer +.
  + Gets severely damaged.

• Backup in Windows XP Wizard allows no choice of drive to create the recovery disk

  Backup Wizard requires a 3.5 floppy to create a system restore disk. When my system and many others have more 3.5 disks... How to solve?

  Original title: windows xp absence of 3.5 diskettes and Backup Assistant

  Hello JohnAdams2461,

  You're right, that Windows XP requires a floppy drive to create the recovery disk.
  Most newer systems do not have a floppy drive.

  View information in a previous thread with the same question.
  http://answers.Microsoft.com/en-us/Windows/Forum/windows_xp-system/cant-create-system-recovery-disk-using-backup/a3e2312b-006D-4f80-940c-254e5f00f1acz

  Best regards, k

  Marilyn