Satellite U400 - stop after the reactivation of the battery charge

Hi all
8 days ago, I bought a Satellite U400 laptop, and all the drivers and BIOS are up-to-date.

I close cover mode standby when the battery on charging with AC main branch and led red indicating the charge is ok...
When he is awake by opening the cover, red led is off load display, but the icon on the right buttom it says on AC and battery recharges.
But it is not charging and the battery level drops.

Is there someone actually deal with this problem?
Thank you for your support in advance.

Hello

Are you sure you have the latest version of the BIOS of your laptop?
Check again on the Toshiba site:
http://EU.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download drivers

The reason why I ask is that I founded this Toshiba document and in my opinion a BIOS should solve the problem.
http://APS2.toshiba-tro.de/KB0/TSB8702EU0001R01.htm

Welcome them

Tags: Toshiba

Similar Questions

  • Satellite A200 stops after the post

    Hello.

    I replaced the motherboard that was dead with a used one on ebay, the user declares that it functioned very well.

    Anyway after that I set up everything, it starts for a few seconds and then stops.
    Then I tried connecting the Council, except in the case of the laptop and it's the shutsdown, after awhile, except in certain positions, or if I press somewhere, then he has not stopped.

    I have reviewed everything carefully and I don't see any evidence of anything whatsoever that could short the motherboard...
    I took a few pictures for you to see how I managed to do work for a long time:

    http://I54.Tinypic.com/ojnix5.jpg
    http://i51.Tinypic.com/2upekw8.jpg

    He got up on the upper right. If I normally put it will not work.
    The strangest thing is that if I go into the BIOS by pressing F2, he used stop! forever there remains, after the POST, that is the case...

    But if meet the thing and tighten all bolts, even its worse, shutsdown in 1 or 2 seconds and doesn't show any video...

    What do you think is?

    Hello

    I think that it of almost impossible to say what could be bad exactly.
    If the MESSAGE cannot be passed correctly, it means that something is broken on the motherboard.
    Have you checked RAM?

    Faulty or incompatible RAM can cause this problem but it s just a suggestion

    PS: what about CPU? Is it compatible with the new card mother and chipset?

  • Satellite L300D begins only after the battery has been drained and recharged

    I have a satellite L300D that has a problem at startup. Last week, it closed but got stuck on the "Disconnect" screen for a long time. Finally I manually turn it off by holding down the power button. Don't think no more of him it happened sometimes with my computers. However, when I went to turn it back on - it was nothing. Power lights came to the front of the computer, but not to screen at all. Could not even access the BIOS. Nothing. It was like that for several days.

    Tried all the common solutions - removed battery, disconnect the power supply and press the power button - still nothing. Tried w/o - just AC, just the battery. Even stripped down to the motherboard to see if I could remove the CMOS battery and reset the CMOS but it is soldered on the motherboard. Put all back together, still nothing.

    Finally, I had to recharge my cell phone using a USB adapter and given that the computer had power I tried the usb port and it worked (for example, I could charge the phone - still no screen on the computer). The computer's battery is dead and I plugged it in. That evening, after the battery was full, I tried the computer and it has perfectly worked. Started correctly, shut it down, restarted and it was fine. Unplugged this night there and reconnected again in the morning and... nothing. Just a black screen. No BIOS.

    Killed the battery again then reloaded and now my computer is working again.

    Any ideas on what could cause this problem?

    Thanks in advance.

    Hey Buddy,

    In my opinion her only the only one you can is update the BIOS like Akuma suggested. This problem is not related software so that s the only option you have I think. You can download the latest version of the BIOS here:
    http://EU.computers.Toshiba-Europe.com > support & downloads > download drivers

    If this is not the case, contact an authorized service provider please. Guys can fix all this hardware related problems can diagnose this problem. Maybe the motherboard or something else must be exchanged.

    Good luck! :)

  • LR doesn't stop after the last updated only with force quit

    LR doesn't stop after the last updated only with force quit

    Hi peterc48702056,

    For Windows, I'd say to set the priority of the process in Lightroom as a via the Task Manager

    For Mac, you suggested to copy the catalog to the location on the desktop or another location and then, check if the problem persists.

    Kind regards

    Claes

  • Creative cloud began the download of an update, but stopped after the download of 5 percent. Nothing works now and I can't access anything whatsoever. Help please!

    Creative cloud began the download of an update, but stopped after the download of 5 percent. Nothing works now and I can't access anything whatsoever. Help please!

    Please remove Cloud Creative app using:

    Install the cloud creative app - https://helpx.adobe.com/creative-cloud/help/install-apps.html

  • Satellite L500-1UU - disconnect the battery when it is connected to the AC adapter / CC

    Hello world

    I have purshaced new Toshiba Satellite L500-1UU
    CPU: Intel (r) Core i3 CPU M330 2.13 GHz
    Physical memory: 4096MB RAM
    Microsoft Windows 7 Home Premium 6.1.7600

    My question is: remove the battery when I use my computer laptop while its connected to the AC adapter would be wise or not? This would increase or decrease the life of the battery, or it will not affect anything?

    Is i3 processors have a technique of centrino disconnect battery power whent, it is fully charged?

    What do you think of this?

    Hi Khaild Essam,

    I agree with Akuma. There is no problem, remove the battery when the AC/DC adapter is connected. If you can do it. In addition the battery charge will be stopped if it s at full charge. The laptop consumes energy to AC/DC adapter only.

    If you remove the battery and work with AC/DC adapter only, the battery life will be improved a little because it s not in its use.

    I found an interesting document for you:
    [How to get the most out of the battery | http://aps2.toshiba-tro.de/kb0/HTD9401AZ0001R01.htm]

  • BlackBerry BB Z10 Z10 stops when the battery indicator shows about 35%

    Z10 BB stops when the battery indicator shows about 35 percent without any warning. Does not illuminate until the charger is plugged. Immediately shows charge remaining 40% +.

    Please advice.

    Stephen

    Hello

    Here is a solution I tried after lookng through various forums and type of works for me. A common thing in most of the solutions is to take the battery and sim card out, leave like this for 1-2 hours and put them, I found back in and turn it on. I'm not sure of the logic behind it, but I remember reading that this overshadow the phone battery problems (connected incorrectly - essentially a reset) and begins to charge.

    I tried it 2 days back and I see that it worked for me, at least until now. I cross my fingers.

    I hope it's useful, works at least for few of you.

    Thank you all for the suggestions.

  • Satellite Pro 4600 calibrate the battery?

    Hello

    My Satellite Pro 4600 battery is pretty weird. I always completely load to 100%. But when I use my laptop and it reached 60-65%, it goes down to 3% of the battery. Now, I was wondering if there is a way to calibrate the battery, so he sees it as a battery of 100% full again? Anyone who can help me?

    Thanks in advance

    Hey,.

    Tips for the battery charge.

    Unplug the computer from the power adapter and turn it on. Let the computer battery power until the computer turns off, indicating that the battery is fully discharged.

    Remove the battery.

    Using a soft cloth, wipe the battery packs connectors and AC adapters.

    Reinsert the battery.

    Plug the power adapter from the computer and check the wall outlet, ensuring that the connection is firm.

    When the PC is off, let the battery charge until the icon or the battery light turns green.

    Disconnect the power adapter.

    Remove the battery.

    Wait 30 seconds and reinsert the battery.

    Reconnect the AC adapter.

    Let the battery recharge until the battery status light turns green or the icon appears at 100%.

    Now your battery must be charged completely. Unplug the computer from the wall outlet and turn on the PC. You should notice more autonomy.

    See you soon

  • The battery charge falls even when it is plugged into the satellite series

    I have a laptop satellite and although it recognizes the power adapter when it is connected and that the icon in the taskbar shows "load", the percentage of the battery charge seems down.

    It is only while the laptop is turned on, because it does not charge the battery when it is turned off.
    I didn't know that he used the power of the battery so that hip, so I'm puzzled by this not only why the battery doesn't seem to be in charge, but also why the battery seems to fall once the laptop doesn't have to use it anyway.

    Any help is appreciated!

    Hello

    I saw this problem on my own laptop in the past. even if the laptop is charging, the battery seems to fall in charge.

    This indicates that the battery life is coming to an end, there are a limited number of cycles of load for a battery before it dies.
    Also when you have the computer is off fresh is always lost at a considerable pace, because the battery is good, "die."

    You can't do anything on this issue except to buy a new replacement battery for your laptop computer to a repair center authorized Toshiba. This should answer your question.

  • Laptop crashes after the battery is connected, must charge laptopn until I use it... irritating

    My laptop caused a lot of problems and I don't know why. This is beacause of my driver problem? By the way, my laptopn was bought in year 2007 while the driver is old enough so it's because of my driver? My battery seems fine, I bought it not too long because my previous charged was broken and the new charger autour cost $99.So can someone help me?

    You have a hardware problem-the battery, the charge adapter, the connections between then, or maybe even something else (I can't say without testing).  It is possible the battery you bought is not exactly compatible with your system, if it was not EXACTLY the same battery.  I recommend that take you to a repair shop of computer good reputation for service and a diagnosis of the problem.  You could also send it to the manufacturer for service.  Compare the costs, the calendar, warranties, parts availability, reputation and any other factor consider you important and make your choice.

    Why are removing you the battery in any way - why isn't she always left in the laptop and the charger plugged in during the night (even if the system is stopped) in order to regain full battery charge and this problem never occurs (even if you still have a problem that needs to be fixed - at least irritation will decrease until get you it fixed)?

    And what driver are you talking about?  You said nothing about what driver for this device or is that the problem or when it occurs or when he started or whatever it is - and we have need to know these things to help.

    I hope this helps.  Please answer the questions above before repair in case we discover another possible cause that can avoid this need.

    Good luck!

    Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

  • My computer is no longer warn me entry stop when the battery reaches the critical level.

    My computer is no longer warn me entry stop when the battery reaches the critical level. Officially, it shows a warning sign and told me to shot or recharge the battery when it gets to level criticism, but now he can't, but stop just when the battery has reached its critical level. No warning sign more.
    What should I do to get the warning before the pc turns off when the battery is at its critical level.
    My pc is hp laptop mini 110-3100. Start Windows 7.

    Hi Sage180,

    ·         Did you change in the computer before the show?

    Follow these methods.

    Method 1: Run the Troubleshooter of power.

    Method 2: Follow the steps in the article.

    Solutions to common battery problems

    Battery meter: frequently asked questions

    For reference: take care of your laptop battery

  • How to control the battery charge when you are connected to the power adapter?

    I post here because I want to know if there is any software option that I can use to control on my load while I use the charger and the dough.

    EXPLAIN

    You know in IBM ThinkPad there are some utilities can help you master the power to CUT the battery charge and keep on the power of the charger and the battery is always on standby if it is OFF the bettery then work and never lose anydata

    I want to control the load while I'm working with battery and charger at the same time.

    I hope that claire ;)

    Hello

    It of not possible to control the battery charge using any software.
    The battery will begin to charge if the adapter has been connected to the laptop and it will stop the charge process after the adapter has been disconnected or if the battery is full.

    See you soon

  • Stops after the start-up satellite c660 (5 min or more)

    I have I have Satellite c660 with a problem since yesterday it stops after startup (5 min or more)

    the back cover is very hot, I think its still under warranty but I rader not use Beceause I can't put my laptop very long.

    where can I check the warranty, and is a way to solve this problem myself (without losing my warranty) or something I can try er

    I send I mail to info at [email protected] (Belgium), but it returns Beceause the adres do not exist. : manfrustrated:

    Hello

    I think that the laptop stops because of the high temperature.
    It would happen to prevent parts of material damage.

    Clean the ventilation openings in the past?
    To do this using a jet of compressed air, it's the right tool to make the dust removed.

    I did that several times, it helps to keep good air circulation.

    PS: If you have hardware problems with your Toshiba devices, the first person to contact is the Toshiba authorized service partner in your country

  • The fan stops after the Satellite U500 - 10Jwas turn

    Hello! I need help!

    The fan stops after turn backwards to laptop my laptop Toshiba gives me the warning "a problem with the cooling system has been detected. Please, turn off computer immediately and return it for service.

    The fan works for several minutes and stops.

    I clean all the dust, I do not have anything with the hardware and software.
    What the reason for this?

    Hello

    What model of laptop do you have exactly?
    It looks like a cooling module problem for met.

    I think it needs to be replaced and this can be done by Toshiba service in your country.

  • Satellite A10 dies after the power LED blink

    Hello

    I have a problem with the power supply of my Toshiba Satellite A10. Sometimes, after the computer sat for some time, I have a problem with the power. The "plugged power cable" - LED will start to blink and shortly after, the computer just dies.

    It can also have the time to go into a lower energy state before he does. When it happened once, it will most likely happen also when I restart the computer, but after a much shorter time. WXP won't even have time to start. If I stop to select the source of start-up, the problem will occur anyway, this isn't the software. It should also be noticed that when the computer is not turned off, the 'smart power' - is on correctly.

    I know that my battery is not very good. Completely loaded, the computer can run for maybe 3 minutes with only the battery. I know that I must have a battery connected, even if I use the power cable, but this occurs even when the mine problem. The battery would be pretty bad not even allow me to use the computer with a cable?

    It should be added, that sometimes I can use the computer for long periods of time without this problem to happen. I also have a problem with the battery not being not properly in physical contact with the pins of the computer, but this isn't the problem here, because I have the same problem with the battery removed and me holding the battery in place.

    Thank you for your help.

    Andreas

    Hello

    You description is very long and detailed and it of still not easy to say what's wrong.
    Usually, the DC-In witness lights up green when DC is provided FRO the AC current. If the output voltage of the adapter is abnormal or if power outages, this indicator flashes orange.

    So I think that is your AC adapter malfunctions or there is something wrong with the electronic power supply on the motherboard.

Maybe you are looking for

  • Additional monitor on 5 k iMac

    I soon in the market for a new Mac and considering the iMac of 5K, well who wouldn't? I currently have a Mac Pro (early 2008) and two Cinema Display 20 "with DVI connectors, which are always excellent and I love them. I would use at least one on them

  • I can't change the brightness Displal in my Probook430

    Hello. I recently bought a HP Probook430 and installed Windows 7 Ultimate 32 bit and I don't seem to be able to change the brightness of the screen, using the fn + f9/f10 (although volume settings are changed in the same method smoothly). Although th

  • Pavilion dv6-1350us: dv6 1350us

    HelloMy computer is a Pavilion DV6 1350us model, serial number [personal information deleted]. The original operating system was Windows Home Premium, but I recently upgraded to Windows 7 Enterprise. Obviously, this can change certain requirements dr

  • I need to access a shared resource by a Linux via NFS server from a Windows XP client.

    original title: access an nfs share I need to access a shared resource by a Linux server via nfs from a Windows XP client. I suggested to install "Windows Services for UNIX Version 3.5" and I downloaded it, but: I see only an English (or maybe Japane

  • Error 1320

    I try to install ActiveClient 6_1 for a reader to ACCESS on my laptop. Everything's fine until the Installation Wizard of the shield of configuration allows you to copy the files. It stops at halfway and I get the following message: error 1320. The s