SatelliteU300 will not start with power connected and fully charged battery

Similar Questions

• Satellite A200 - will not start with power supply connected

  My lapop is 2 years old. Whist trying to boot it restarts at least 2 times and I am running Windows 7.

  My old battery lasts about 20 minutes so I bought a new and the first time that I loaded up it gave me an hour of a time value of battery, but on the second cooldown it has provided for 20 minutes.

  It does not always to the top while the power is connected do you think that my motherboard is defective =.

  Hello

  Normally, if you connect the laptop AC adapter shouldn't t stop. Everything should work correctly as the system even starts the battery would be defective.

  So, I think you already wrote that the motherboard is faulty. In this case I recommend to contact an authorized service provider. Technicians can order a new mainboard and Exchange! :)

• My CS will not start with error code 16

  How can I find the serial number CS5.5 under MAC OS X if I want to reinstall it? My CS will not start with error code 16, he says: configuration error.

  Please visit the Doc KB: http://helpx.adobe.com/x-productkb/policy-pricing/configuration-error-cs5.html

• A5383 S55D satellite will not start without power

  Hello!

  I have the Toshiba Satellite S55D A5383 laptop and I have a problem with the battery, I think.
  Laptop does not start without power. What is happening since last week.
  In fact, since April 2015 battery does not last as it did when I bought (may 2014).
  I have'nt registered the product and I think I'm out of warranty.

  So, what can I do to fix this?

  You'll probably just get a new battery which is what I did. Try Amazon.

• iMac will not start. From sound and sometimes Apple, but no further details. How can I get?

  Just got an iMac and it will not start up.  I can get the sound start and, sometimes, the Apple logo, but it stops there.

  Have tried to use 'command-option-P-R' together. Have you tried "D".  Tried "control C".  Are there other possibilities that I could try?

  Install or reinstall OS X from scratch

  Make sure that you have backed up your files because the following procedure will remove all of the hard drive.

  HD recovery start:

  Restart the computer and after the buzzer, press on and hold down the COMMAND and R until the menu screen appears.

  Erase the drive:

  1. select in the main menu disk utility and click on the continue button.

  2. once the charges of THE select your boot volume (usually Macintosh HD) in the

  list on the left. Click on the Erase tab in the main window of THE.

  3. set the type of format Mac OS extended (journaled). If necessary, click

  Security and button all the option data from scratch in a single pass. Click

  the clear button and wait until the process is complete.

  4 leave FROM and return to the main menu.

  Reinstall OS X: Select reinstall OS X and click on the install button.

  Note : You will need an active Internet connection. I suggest to use Ethernet if possible

  because it is three times faster than wireless.

  This should install the version of Mac OS X that you had installed it.

  If this does not work then your hard drive has failed and must be replaced. Please make an appointment at the Apple Store - Genius Bar store and bring it into service. If you are in the United States or is unable to make an appointment in this way, contact your Apple store.

• Satellite L40 don't stop with power connected and is not in sleep mode

  Hello world. I hope someone can help me. Basically, there are two problems: one with judgment of the laptop (Satellite L40 - 17U (Vista 32 bit Home Premium SP1)) down when power is connected and the other with closing the lid and put it to sleep.

  1. in recent weeks, it all of a sudden won't stop, whenever power is connected. When it's on battery, it will stop. When the power is connected, and I try to stop, it seems that it closed down (all activity stops and the led goes off) for about 1 or 2 seconds, then it goes back.

  2. when I close the lid (all settings in Vista are set to put the laptop in a State of 'sleep' when the lid is closed), the laptop enters a State where it cannot be recovered by stopping by pressing the power button for 10 seconds to close completely. When closing the cover, only the battery LED continues to Flash orange (the way it should be), but apparently the laptop keeps consuming power, because when I restart later (first having to close as described above) tends to be quite an empty battery as it was before the next redΘmarrage it (like go from 100% to 65% in 30 minutes as "standby mode"). Also, when I open the cover, the other LEDS will on new (green), but nothing happens.
  After the restart first by pressing the power button for 10 seconds to close, I often get the message that Windows cannot be started and run the system repair.

  I just do a completely clean install with the product recovery CD (has not installed SP1 yet), updated to v1.90 BIOS, but the problem remains.

  I'm afraid that my only option will be to bring him away for a warranty repair, but knowing that these repairs can take weeks, I'd rather try a solution here could someone recommend me first. If you have any ideas, please let me know.

  Thank you
  Daniel Breslauer

  Hi guys

  Never had this problem on my laptop, but with regard to an other users here in the forum the BIOS might help solve such strange behavior for laptop
  To be honest the closed question is unclear for me I noticed a problem before on my laptop but the update of the BIOS helped.

  This is why I recommend update BIOS first.
  If the problem still appears, the ASP should take a look in the notebook.

  Good luck

• Computer will not start with Windows. I get a black screen and a blinking cursor.

  Windows XP Home Edition startup problem

  I have Windows XP Home Edition, but the computer does not start at the top.  I get a black screen and a blinking cursor.  I have an XP installation disc.  I was in the Recovery Console to recover all of the standard tasks, but nothing helped.

  Brand, model and model number of your PC?

  Are you able to get into the BIOS?
  What took place prior to this problem?
  For now, you can read this to get some ideas:
  http://tips4pc.com/computer-problems/my-computer-boots-up-to-a-black-screen-with-a-flashing-cursor.htm

• Tecra M2 - will not start, the power light is on

  Hi, I wonder if someone out there could help me with a problem?

  I was using my M2 Friday when my friend accidentally hit a very small amount of beverage on the front of my M2, I immediately got up and got a hair dryer on it.

  After leaving it an hour I tried to use and everything worked as before which was a great relief, but a day later, I used the M2 to check my e-mail address when all of a sudden went.

  The power led is on was still and so was the light that indicates I have a CD player, I tried several times and it wouldn't start, so I went again for a day and yesteday morning it seemed that it was starting up only to freeze on the Windows screen, he then returned and he has not started since.

  Could you please give me some advice on what I could do to fix this?

  Kind regards

  Russ

  Hello Russ

  Be realistic. What you can do in this situation? Not much! You can try to start the machine. See if you can get into the BIOS and if yes how long the device will remain on. If unit is running for an extended period, you can try to boot from the CD (for example with the recovery media).

  You can try to connect as another external HARD drive to another laptop and try to back up all your important data and reinstall the OS. More than that is not possible. If there is an electronic failure, it is not easy to fix on your own and support technical investigation just to see what hardware is damaged.

• GTX 750 will not start with HP P7-1233w

  Hello
  
  I use a desktop PC HP P7-1233w and the EVGA GTX 750 will start at the HP Logo blue screen and after about a minute it will boot to a black screen (and that's all). When I leave the card it starts very well. I know that my diet is very well that others have used a GTX 750 Ti with the same block of power SUPPLY HP OEM as mine.
  
  When the system comes on, I hear the spinning card fans. So I don't know, it's getting power and video. I tried everything, including clear CMOS. I also started in Mode safe, off the map graphic, firm and installing the card. Just to get the same thing.
  
  In my system motherboard is a MSI MS-7778 (Jasmine). I thought that it could have something to do with the UEFI settings and inheritance, but there is no option in the BIOS and there is apparently no updated BIOS for my motherboard.
  
  If someone could help me, that would be greatly appreciated.

  Hello

  HP P7-1233w was released in may 2012, and HP has not started to ship full UEFI level consumer computers to office until the middle of October 2012.

  Modification on the motherboard to a card mother UEFI would require a new license of Windows 8. Windows 7 will not work in UEFI mode without some special hacks.

• Pavilion p6 - 2120t: Windows will not start with the new graphics card

  Installed a Zotac GT 740 profile down in my desktop PC graphics card HP Pavilion p6 - 2120t and now the PC does not start.

  HP Pavilion p6 - 2120t CTO desktop PC

  Configuration:
  Intel Pentium CPU [email protected]
  4.0 GB RAM
  Intel HD Graphics Driver version Family: 8.15.10.2291 dated 27/01/2011
  Motherboard: IPISB-CU (Carmel2) (1 open PCI Express 16 expansion slot pins)

  BIOS to Version 7.18

  Running:
  Windows 7 Home premium 64-bit w/service pack 1
  Two monitors (VGA, 1 digital port 1)

  Before installing the new graphics card, I replaced the power supply original 300w with a 400w power supply.

  For starters, I disabled the onboard graphics in Device Manager. Then, I opened the case and installed the GT-740 in the open PCI Express slot. I made sure that the card was fully engaged in the slot.

  I plugged both monitors to their connections voted on the new map.

  When I tried to boot the PC, the digital monitor displays the screen HP (the one that indicates which key support to achieve the start menu) and then frozen. No other entries of key or mouse have been accepted.

  The PC then sounds 4 short beeps (about 10 seconds between each beep) and then a long beep before turning off the signal to the screen.

  Then, I removed the new graphics card on the PC that starts then. I have reactivated the original graphics drivers and the PC then worked normally.

  Tried the above process two more times with the same results.

  I then went into the start menu to look at the BIOS. The menu of the BIOS shows two options:

  > Sources of boot UEFI

  Windows Boot Manager

  > Sources of boot legacy

  ATAP I CD/DVD player

  SATA2

  Hard drive

  SATA0

  Network controller (Realtek PXE B06 D00)

  PC using UEFI Boot Manager Windows boots normally

  I have not tried Legacy Boot Sources because I don't know which one to choose.

  I went to the HP site and looked for an update to the newest BIOS, but updating them is a rev version 7.16 while my PC shows my BIOS to version 7.18

  I know that others have had a similar problem but I have not seen a solution that works for my PC.

  Any advice would be welcome.
  Thanks for your time.

  Hello

  Your PC isn't spec'd to run Windows 7 using the Windows Boot Manager.  I expect to a UEFI-based graphics card likely to work on an HP PC that does not have a BIOS version 8.

  The below listed OEM HP, graphics cards should work in your PC using a normal non - UEFI W7 and W8 installation.

  

• I have a aspire 5517 who will not, start seeing power turns on but nothing else happens.

  I have a aspire 5517 that won't initialize power light turns on, but nothing happens.  I tried to connect an external monitor, but it still doesn't work.  All my stuff is on this computer and I need to save at least. Help!

  Hello..

  You can try to remove the battery, then connect only the power adapter ON the computer and check if you are able to start the computer.

  In order to return the data take the hard drive on the computer startup and slave with another computer and you will be able to transfer the files from the hard drive of your computer to another.

• My Acer Aspire R14 does not start with the cord of the charger plugged in with the battery connected to

  A few weeks ago, my laptop Acer Aspire R14 went totally blank. When I unplugged the power cord, it started right to the top, but at the moment where I plugged the power cord back inside would be closed. The battery dies quickly in this way, because it would not charge. I removed the battery then it started upward with the power cord. I thought it must be the battery, so I installed a new battery. which is not to change the problem.

  So, I ordered a new motherboard and after a few weeks, I received it today, installed, and I have always the same thing. It works well with the power cord plugged in until the battery is disconnected. But at the time wherever I connect the battery, everything stops, not to be revived unless I disconnect the battery.

  I need help! What could be the problem?

  Glad I could help.

• Laptop does not start with the connected usb device

  Hello
  Voila, I have a Sp6100 Pro Satellite, when I try to start whith a usb printer is connected, the laptop does not start. I have the latest version of the bios 1.90.

  THX,
  Barzot @+.

  Hello

  What you mean with start won t at all? Is there any kind of reaction if you press the power button / stop?

• computer will not start with the disc

  I use vista and my computer does not start because of a corrupted file.

  I put my vista disk in such suggested, but the screen does not move any command of keys to press and just goes round in a loop. So I can't the computer to start and fix.

  I changed the bios to boot from the cd as first choice but still no results.

  can anyone help?

  Could it be that the disk driver does not work like the disk isn't loading? Or the disc will not load because the press any key order is not coming?

  I am old enough and not very technically experienced but this computer has served me well and I have a lot of information that I need to go down there if I have to buy another.

  Any help would be greatly appreciated.

  If you have correctly setting the boot order in the BIOS to CD/DVD first, and the computer does not start, your problem has nothing to do with the driver for the CD/DVD drive. Also running in safe mode or SFC can maybe help you.

  The reason that pilots, safe mode and FCS can help you is the same for all three: boot (if from the hard drive or a CD or DVD) takes place before loading Windows. If it boots from a CD or a bootable DVD, the problem has nothing to do with Windows. It's a hardware problem. I don't know what the problem is, but it is possible that the CD/DVD drive is dead.

  What is wrong can but fixable, but whether it is cost-effective to do so is another matter. It depends on what the problem is. If the CD/DVD player, they are inexpensive, so replacement should not be expensive. Fortunately, it's not like there is a problem with the hard drive, so even if you buy a new computer, you must be able to remove the hard drive from the old computer, put it in an external enclosure and to transfer the data to the new computer.

  Let me add another point: you say "I have a lot of information that I need to get off it if I have to buy another." This suggests that you don't regularly back up your data on an external support. If this is the case, you've played with fire. It is always possible that a hard disk crash, the user error, close to love at first sight, virus attack, even stolen computer, can result in the loss of everything on your drive. As it has often been said, it is not a question of whether you will have a problem, but when.

• System will not start completely, blue screens and then restart

  Well, I need serious help. I have Windows 7 and installed Ubuntu on my XPS M1730. Yesterday my laptop shuts off and when I went to put it back on it would start start and then blue screened and restarted, continuing the cycle. I tried to use the system restore (Gets an error). I also tried to reformat using the Windows Vista disk that came with my laptop. It does not start, it just goes to the screen where I can choose between Windows 7 and Ubuntu. My friend is here and I'm on this laptop, and we wanted to play our game together. So please help quickly (if it is a command line or other) then we can game. Thank you :D

  To boot from a DVD, positioned on the BootOrder:

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu

  For any question on Windows 7:

  http://social.answers.Microsoft.com/forums/en-us/category/Windows7

  Link above is Windows 7 Forum for questions on Windows 7.

  Windows 7 questions should be directed to / stationed there.

  You are in the Vista Forums.

  See you soon.

  Mick Murphy - Microsoft partner