Scan to computer in Officejet Pro 8600 Plus

Similar Questions

• Unable to scan from my HP OfficeJet Pro 8600 Plus to my Mac iOS 10.10

  Just bought a new Mac and execution of Yosemite. Tried to add my 8600 and it prints but will not scan. When you try to scan to the computer, a message "the HP software required for the Scan of the computer could not be located on this computer. Please download and install the latest HP recommended software for your device to http://www.hp.com/support and then try again. "When I followed the link, he directs me to download the driver again... and the beginning of the cycle. I tried to uninstall completely while following the previous suggestions in the forum, but nothing did.

  I'm a new Mac user, but just can't understand why it would work on my PC and not the new Mac.

  Hi castagmc,

  Welcome to the HP Forums.

  I see that you experience a problem when you attempt to get the new Yosemite driver installed for the printer.

  I have some suggestions that we can try to solve this problem.

  First of all, please remove the cable usb from the printer and Mac and leave that it disconnected until further notice.

  I have a link that I give you which gives detailed instructions for uninstalling the printer software.

  Once the uninstall is complete, reboot the Mac for changes to take effect.

  When the Mac is back running, disable any anti virus protection, you can running. We don't want anything to get in the way when reinstall us.

  The next step is to download and install the HP Officejet Pro 8600 series full feature software and drivers.

  The installation will prompt you as to connect the usb cable then please do not it connect before hand.

  Please do not hesitate to write me again if you have any other questions.

  If troubleshooting doesn't help not solve your problem, then I would say call the HP Technical Support to see all the other possibilities for you. If you call in North America, the number is 1-800-474-6836 and for all other regions, please click here: click here.

  Thanks for your time.

  See you soon,.

• Re: How to scan legal size in OfficeJet Pro 8600 Plus documents

  How to scan legal size documents in Office Jet Pro 8600 Plus?

  In fact, the problem was located. I is broke and finally called HP support. It turns out that, contrary to the information that I have seen elsewhere, legal size paper MUST be analysed the ADF, not the dish. You can see a white band across the plateau where the search starts. The dish is physically unable to accommodate legal communication. Once the original is loaded in the ADF, the size of the document options now include legal communication.

• HP Officejet Pro 8600 Plus: HP Officejet 8600 does not scan to computer more - after having moved from the House

  Equipment:

  HP Officejet Pro 8600 more

  MacBook Air mid 2011

  Mac OS X Lion 10.7.5

  ASUS router DSL - N16 (new)

  I moved home and brought my computer and printer with me. I chose a new access provider and sent the new router.

  My old House my computer and the printer/scanner worked fine. Now set up at the new House and I can print but it won't scan. The computer and peripheral HP are connected to the router. I uninstalled all the HP software and reinstalled. On the front of the printer if I select Scan of the computer he says not 'found computer.... ' Make sure that the feature is enabled"using the HP utility. But in the HP utility there is not the option "Scan to Computer" more. I used to be able to scan to the computer to the printer, and I used to have a scanning tab in system preferences / print and scan - but not more!

  Details of what I tried:

  1. Uninstalled HP software.
  2. System preferences / Print & Scan - removed all printers.
  3. On the front of the printer: you click Network and disconnected.
  4. Off, computer, printer and router.
  5. Tour of router on. The printer is turned on.
  6. Used the wireless configuration wizard.
  7. Chose my router - "Found WPS router".
  8. The router WPS button is pressed. 'Network connection' 'successful connection' (n.b. left wireless live 'Off').
  9. Turned computer on - check the connection to the router OK.
  10. System preferences / print and scan - Add printer. He sees my printer - I select this one.
  11. Option to download and install the software of Apple-selected.
  12. Printer appears in Print & Scan-Idle / green spot. There is a print tab and a scanning tab.
  13. Click on the power levels: "Information not available". Click the HP utility: "unable to communicate with the device selected. Try to print: "the printer is not connected.
  1. Go to support.hp.com/gb-en/drivers - type in the printer model.
  2. Download the installation software "HP Officejet Pro driver software and full functionality" version 12.23.0. Save the dmg file.
  3. HP download and install the wizard downloads files on computer. Click on dmg download, double click on HP Installer.app.
  4. Click the HP Installer dialog box. Ignored HP ePrint offer.
  5. "Select the device you want to install" - no device is listed. Click on «my device is not listed...» "and"continue ".
  6. Select model device drivers - 8600 network / wireless Officejet Pro. Installation options: checked HP recommended software and additional software.
  7. Software installed with success, but still need to configure the device. Press to continue.
  8. Device not shown yet. Add device manually, using the IP address of the printer. Printer is displayed.
  9. 'Add the Print Queue' box - must add the printer to the system by using the "add a printer".
  10. Click IP in the toolbar. Protocol: HP Jetdirect - outlet. Enter the IP address of the printer. "Print using" field shows my device. 'Add '.
  11. Back to the installer - congratulations! Successfully installed.
  12. Utility HP ok - prints ok.
  13. On the front of the printer: select Scan / scan to computer: «no Found computer...» Make sure that the feature is enabled. Mac OS X: open utility HP. Under scan settings, click Scan of the computer, and then make sure Enable Scan to computer is selected. »
  14. In the HP utility, there is no "Analysis settings" or "Scan to Computer". There is "scan to E-mail and"Scan to Network".
  15. In the system preferences / print and scan - it doesn't have the printing tab and the tab analysis (see 12 above)
  16. Check the built-in Web server. Wireless status is connected. On the scanning tab I can Webscan to computer (but only 1 page at a time - not good for multi-page documents!)
  17. Try Apple Image capture - no devices specified in the list of devices.

  Hello

  First, make sure you have the latest firmware installed as follows:

  http://support.HP.com/us-en/product/HP-OfficeJet-Pro-8600-plus-e-all-in-one-printer-series---N911/4322915/model/4323647/document/c02919168/

  Then, try the following:

  1. Of the printer, click on the right arrow / left and press the ion of the configuration of the printer.
  2. Select Network Configuration.
  3. Select direct Wireless Configuration.
  4. Ensure the Direct wireless is enabled and take one step of his password if such a value.
  5. Click on the WiFi icon from your Mac and connect to the SSID 8600 spirit "live / Print" in its name.
  6. Go to System Preferences > print and scan and click on the plus sign to add the printer - you see it listed as Hello via the direct wireless connection?

  Please let me know the results, if it not listed as Hello with Direct wireless, which clearly show that the new router interrupts the multicast connection, this is the same as the connection through a different router.

  On your screenshot, it seems that your router do not transfer packets to multicast to the need...

• Scan more OfficeJet Pro 8600: Officejet Pro 8600 Plus resize problem

  With the help of Officejet Pro 8600 Plus to scan documents on computer in PDF format.

  I'm tring to scan a document that contains very important information just at the foot of the page, but when the scanned document appears on the computer screen, I see that he has not captured at the bottom of the original document.

  I can work out how to resize the document to the copy function, but I can't find an option to resize for scanning.

  Nobody knows the answer to my woes?

  Thank you for your help.

  Hello

  Thank you for using the forum.

  You can choose the scan size, example as shown.

  

  In addition, these videos may be useful for you:

  Scanning multiple photos:

  HP Officejet Pro 8630

  https://goo.GL/ADYDmo

  Scanning tips:

  HP Officejet Pro 8630

  https://goo.GL/fjZvqM

  Hope that helps.

• HP Officejet Pro 8600 Plus Scan quality issue

  Hello

  I just set up my HP Officejet Pro 8600 Plus, and everything seems to work properly.  I am really disappointed by the quality of the images so, so I thought I'd see if anyone has experienced the same problem?

  The scanned images are very dynamic, but are too.  Detail is lost in the scan either because the brightness, or because the scanner is not properly using the resolution I have him ask to scan (600 dpi).  I have tried various different brightness and contrast settings in the scan dialog, nothing helps.  Printing HP and Scan Doctor reported no problem.  Increase the resolution of scanning on the 8600 is not helped either.

  I joined a segment of an image of the 8600 and a lot cheaper all-in-one I expected to replace, a canon mp630.  I have bought the 8600 because the scanner component had good reviews, but based on my experience, that I'm starting to have my doubts!

  Please let me know if you think there's nothing I can do to improve the quality of the scans?

  I use Windows 7 Ultimate, 64-bit.

  Thank you

  Pete

  8600 scan 600 dpi (Note lack of paper grain)

  

  Canon MP630, 600 dpi (capture of paper grain, wash the details)

  

  Unfortunately, I must point out that the replacement was no better.  It's a real shame, old flat scanner HP I was replacing with the ACM was high quality, but the Pro 8600 scanner was simply not enough good.

  Ultimately I exchanged for another manufacturer MFP that produces a large part analysis better (even if printing is not as good).

  I had much rather have paid more for a higher quality scan on the HP, but this option is not available to me, which is a shame!  On the 8600 Pro scan color reproduction was great, but there not only to capture the details.

  You can adjust for color problems in the software, but if the detail is not captured, you can't put it in!

• Officejet OfficeJet Pro 8600 Plus: Pro 8600 more will not scan from touchpad after updating Windows 10

  After a Windows 10 update, my printer will not touchpad analyze. It will scan the troubleshooting utility. I unplugged and reset without success. I have updated to the latest version of the HP software for the printer. What else can I try?

  Hello

  You can try to install from the link here:

  http://support.HP.com/us-en/drivers/selfservice/HP-OfficeJet-Pro-8600-plus-e-all-in-one-printer-series-N911/4322915/model/4323647

  Before installing the HP software above, please uninstall your previous version first.

  During installation, select the type of standard or recommended installation when you are prompted by the installation software. If you choose a minimum installation, read the description of each component software with caution to avoid the unintentional loss of functionality of the printer.

  You can check via "Control Panel" > "Hardware and sound"-> "Devices and printers"-> under "printers and faxes". There will be a green check mark is marked to your printer if it connected successfully.

  Hope this helps you.

• HP OfficeJet Pro 8600 Plus - ADF scanning problem

  Hello

  I recently bought this printer and used without problem for almost 2 months. However, right now I am struggling with the ADF.

  When I put a document to scan by ADF, I have a thin, black line on re-impressions. It is on the right side of the page, starts from everything at the top and goes down all the way.

  I have even if it is a kind of alignment line (you know when we write try, or its composition, leave us space on both sides)

  This problem does not exist when I scan and print documents of old school way, aka analysis usual. Only the ADF documents'ed have this problem a little. (The thin black line on things reprinted)

  Any recommendations?

  Best regards

  Update: I did what jason_h suggested in step 1 and it worked, this can be closed:

  http://h30434.www3.HP.com/T5/scanning-faxing-and-copying/HP-OfficeJet-Pro-8600-plus-ADF-copy-scan-line-down-length-of/m-p/2942099/highlight/false#M69757

• HP Officejet Pro 8600 Plus: vertical line when scanning

  I get a vertical line when I scan using the document feeder.  I do not understand when scanning the glass plate. I need assistance to access the mirror slider.  I raised the lid for the loading of documents, but I couldn't find out how to get under the rollers to clean the mirror. Thank you

  The document here can help solve the black lines to scan using the ADF on your HP Officejet Pro 8600 Plus.  From my experience this is almost always caused by a specification on the thin glass on the side left which is used for scanning using the ADF.  Cleaning of this area as described in the above document should solve the problem.  If the initial cleanup does not resolve the problem, it can help to shine a bright flashlight almost parallel to the glass.  For a line on the left side of the printed page, the place will be toward the front of the printer, if the line is on the right side of the document, it must correspond to a specification to the rear of the printer.

  Figure: Clean the ADF scanner glass Strip

• HI, how can I scan a picture and only the witout the rest. On a HP Officejet Pro 8600 Plus?

  HI, how can I scan a picture and only the witout the rest. On a HP Officejet Pro 8600 Plus?

  When I scan I got my photo and all white for the rest of the screen

  It has no function of machine harvest in the 8600 software. To get the exact size, you will need to manually set the size for the scans that you do. You can find the setting by clicking on the blue link to advanced settings in the first scan window. Will take you to a place that will allow you to change the size of the scanning area. Hope that helps.

• OfficeJet Pro 8600 Plus: Officejet Pro 8600 Plus 'Sweep of Pin code function' Windows 10?

  In Win7 that I could click on start/programs go to HP, click on and he would drag with various categories which was Scan. I could then pin the shortcut to scan on my desktop or start.

  However, falls with Win10 you click on all the Apps/HP Officejet Pro 8600 most and there is nothing to see but pin all of the module that is already on the desk of the installation.

  How can I get just the pinned shortcut to scan?

  I tried directly open scan with the .exe only two that had the word scan in the programs but the scan did not open.

  Mark

  Hi @markg2,

  Thank you for showing your interest in the HP's Support Forums!

  I see that you want to create a shortcut to the HP scanning. I will definitely do my best to help you and don't forget to come back to this thread and mark "Accept as Solution", if I have successfully helped solve you the problem. If you want to say 'Thank you' to my effort to help, click on the "thumbs up" to give me a Kudos.

  I understand how frustrating this is for you. Windows 10 has made some changes, so that the steps are slightly different from Windows 7.

  Please follow these steps as a guideline:

  1. First of all, we need to locate HP Scan where on the computer. The default location is in Program Files. For example, C:\Program Files (X 86) \HP or Hewlett-Packard.
  2. Go to (C:\Program Files (X 86) \HP or Hewlett Packard HP Officejet Pro 8600 Plus\Bin)
  3. Right-click on HP Scan, and then click send to.
  4. Left click on desktop (create shortcut) to place the shortcut on the desktop.

  For more information, see this paper:
  Create the shortcut on the desktop in Windows 10 for a program (announced)?

  I hope this information is useful. Please reply to this message with the results. Good luck!

• Not completely scan legal size with Officejet Pro 8600 more Documents

  I'm trying to scan legal documents of sizes on my Officejet Pro 8600 Plus new. I have gone through the forums, and this has been a recurring problem in the past (see link- http://h30434.www3.hp.com/t5/Scanning-Faxing-and-Copying/Scanning-Legal-Size-Documents/m-p/35416#M14...   ), but doesn't seem to be resolved. If I use the document feeder or glass, the paper is cut down and seems to be stopping at the "A4", legal vs. size. I can't find any setting on the scanner itself, or in the HP Utility software to change this, or even to be able to identify the current configuration, if it is a.

  I use a Mac Pro, system 10.6.8 just installed and started using the printer a couple of days, and everything is up-to-date software-wise. Everything else on the machine works beautifully.

  Can anyone identify what is happening here and how to fix?

  Thanks for your help - I chose precisely this particular unit on the next model down because of the glass/size bed legal, and if I can't use it to scan legal documents, well, it's a problem. Thanks for your help!

  Hello

  Please, try the following steps:

  1 open the HP utility and select your device.
  2. based on Scan Settings open the "Scan to Computer".
  3. click on the tab "scan tasks.
  4. Select the shortcut Scan allows to analyze, and then click on edit.
  5. in the section of scanning from an HP device, click the blue triangle to expand the menu.
  6. in the expanded menu now, open the drop down next to cultures in and set as none.
  7. click OK and try to scan the image.

  Please let me know of any changes,
  Shlomi

• Automatically create color PDF can not deposit Officejet Pro 8600 Plus

  I have an Officejet Pro 8600 Plus and an Apple OSX Yosemite iMac running. I installed the full software from the HP support site, and in particular the analysis of the HP is version 4.4.1 (21).

  I want to create a color PDF directly in a file on my computer to the scanner.

  If I select Save as PDF, I get a b & w image in a file that is automatically created.

  If I select print daily scan opens in HP Scan and I am able to create an image in color, but with additional steps.

  I looked at other similar topics in 2012 and 2013 and saw advice to change the mode in HP utility/Scan to computer/change Scan tasks/editing, but there is no option of color Mode.

  Finally, I figured this out. It CAN be done.

  Go to HP utility/Scan of the computer.

  Make sure that enable Scan to computer is checked.

  Select Edit analysis jobs

  Select Save as PDF/change

  In the presets drop-down, select generalist

  In the section move the items from the Finder, you can also specify the folder where the scans will be saved.

  Saved color, managed directly from the printer scans on my iMac. Sweet!

• HP Officejet Pro 8600 Plus the Scanner Software

  Hello

  I'm a big fan of HP products.  My last several printers, scanners and computers were all HP.

  I recently bought the HP Officejet Pro 8600 Plus to replace an older machine with similar features (ADF, duplex, etc.).  The previous machine was also an HP printer.

  The problem I encounter is that the software appears to have been downgraded.  The software on my previous machine had the ability to automatically analyze the photos laid on the flat bed scanner in individual jpg.  With the software on this computer, it seems that I need to manually crop each image.  The options for optimization of each picture, eliminating scratches, automatically adjust color, sharpness, etc. are all gone.

  I really miss these features.  I found that I had been using a "basic" version of the software.  I installed the full version and found it a little different, but it still lacks the automatic selection of the image and image tweaks I did this inveterate of.

  Is it possible to recover these options?

  Thank you

  -MrXmas

  What I found there are some good options based on their comments, I'm not sure if they will have all the features you're looking for, but...

  http://goo.GL/Czm1

  http://goo.GL/3KUR

  I would like to know if this is useful!

• HP Officejet Pro 8600 Plus - Duplex printing problem

  I use a printer Officejet Pro 8600 Plus (what is the best printer I've ever had, apart from this problem!).  I use it with Windows 8.1.

  He struggles for more than a few pages print using duplex.  The problem seems to get worse when I print a pdf file.  It starts to print very well and made a few pages, but then I get this message "error on HP Officejet Pro 8600.  "Could not print * name * folder.  It appears on the computer not the printer.

  Any suggestions?

  Thank you

  Hey there @operationorphan

  I just wanted to add my own suggestions here for the issue of two-sided printing that you had with your Officejet 8600.

  You can try to update the firmware: get the latest Firmware and updates

  If this does not help, try to uninstall the printer software , reboot the PC and reinstall the printer. This should dissipate all software problems.

  I hope that helps!

  If troubleshooting doesn't help not solve your problem, then I would say call the HP Technical Support to see all the other possibilities for you. If you call in North America, the number is 1-800-474-6836 and for all other regions: click here.

  See you soon