Scanning from slow PC on 8600 AiO

Similar Questions

• thin horizontal black line down page what scan on HP Officejet Pro 8600 more

  I've owned an HP Officejet Pro 8500 and scan was perfect.  I recently bought a HP Officejet Pro 8600 Plus.

  When I scan from the ADF HP 8600, I get a thin (several pixel wide) black along the lower edge of the analysis that results.  This line will be sometimes slightly twisted or appear only through half of the page, in which case, it tends to become thicker towards the edge of the page).  According to me, this line is an artifact of the analysis of the edge at the bottom of the original document.  I think it is to show where the bottom edge of the page was when parsing.  If the document is that a little offset, then the black line down will be a little twisted, probably following the edge of the page.  This issue is consistent and reproducible.  It is in the mode "Scan mail" and in mode 'Scan To Network Folder.

  When I scan from the flat bed, I get a very narrow black line along the side of the analysis resulting very superior, but the background seems in good condition (although I have not tested this widely).

  These fine black lines occurred when scanning the HP 8500.

  I wonder if there is a setting to adjust it, or if it is a firmware difference between printers needs debugging.

  Hey KenAlker,
  
  There are a few things I want to check if you have lines when scanning using the 8600. I see that mention you that lines appear both through ADF and flat glass. There may be something both of the glass sections used by this printer, but more often that otherwise, this isn't the case.
  
  I would check if the printer is connected to a surge protector. If this is the case, then try plugging the 8600 in a direct outlet. Often the surge protector can cause this problem appears because the printer has a built.
  
  Also, try a hard reset:
  * Unplug the unit while the
  Disconnect the other end of the wall socket direct
  * Wait 30-60 seconds
  * Plug the unit to the top
  
  Also, try to take a look at the steps in the document found here.
  
  I hope this helps.

• HP Officejet Pro 8600 Premium: Printer leaves black lines during copy and scan from ADF

  I know this question has been asked several times, but whenever I try to copy or scan from the automatic document feeder, it leaves black lines on the copy (with the document on the works of glass like a charm).  I've read through the forums and have tried the advice to unplug the machine and so on, but none of these suggestions work.  Any help would be appreciated.

  Hey @Huskers1,

  Welcome to the HP's Support Forum!

  I see that you have some problems with a line when copying from the document on your Officejet 8600 Premium feeder e-all-in-one printer. I can help you with that.

  To start, make sure that the printer is plugged directly into a wall outlet, not a surge protector. Once done:

  1. Get a little water and a lint cloth.
  2. Open the left upper part of the printer, where the document since the charger goes into the printer. It should open up as you opened a book.
  3. With your damp cloth wipe the rubber stamp, the rollers in the cover and the casters on the bottom of this section.
  4. Again open the left side of the printer, as you opened a book.
  5. With your damp cloth, wipe the rollers, you will find inside this section.
  6. Close the upper sections of the printer and open the flat section.
  7. With your damp cloth wipe the rollers and the white bar you see on top of the printer
  8. Clean the glass on the left side of the printer.

  Once all the pieces you cleaned dry, please let me know the results. If you remove the line, click on accept solution. If you appreciate my help, please click on the thumbs up icon. The two icons are below this post.

• Option missing Scan from the control panel for my Officeject HP 8600 pro. How can I get that back?

  I have this printer for a few months now - it works well until today.  Option missing Scan from the control panel for my Officeject HP 8600 pro.

  I have Windows 7

  Access has been-

  Beginning

  Devices & Printers

  HP Officejet 8600

  He opens a box that had a detection option (later), which I clicked to bring up the scan dialog box.

  The option disappeared. I have no idea how it happened.

  How can I get that back?

  1. first of all uninstall the software

  • Click on start button, then go to programs > HP > Officejet 8600 and click on Uninstall.

  2. then go to Control Panel > programs and features

  • Officejet 8600-click and then click on uninstall a program
  • 

  3. then download the software on the HP web:

  •  HP Officejet 8600 - drivers and full software features - Windows 7 64 bit

  4 and install with the downloaded software.

  Hope these steps help you,

  * Click the stars KUDOS to say thanks

  * Click the accepted Solution if the answer to the question.

• My OfficeJet Pro 8600 more returns "not recognized computer" when I scan from desktop computers.

  My 8600 OJPro more has been configured to recognize my Dell computer.  What settings should I on my computer for the printer OfficeJet Pro 8600 more allow scanning from my Dell desktop?

  I would try to run printing HP and doctor Scan first to see if the problem can be solved with this automated tool.  Click here to access the tool.

  Thus, there are measures to check the WIA service:

  (1) type services.msc in the section run or search programs and files

  (2) scroll the WIA: Acquisition of Image Windows service

  (3) to ensure that this service is running.  Click on stop, and then restart to ensure that the service is running properly

  (4) restart the PC to see if WIA will resume functionality

  (5) check the properties (right click on WIA) 2 dependencies are defined

  (6) check to make sure that the remote procedure call (RPC) is running

  (7) check the detection equipment core and make sure that this forum works

  Let me know how it goes.

• Scanning from a new touchscreen PC from HP

  You just buy a new HP Envy23 touchscreen all-in-one PC and then put the CD for my printer HP Photosmart B109n-z existing must only be presented with the option of an "out" when the installer loaded.  Plugged the printer on the PC using a USB cable and was able to print.  I no longer have the program of "Center of Solutions HP" on my new PC however and so cannot run a scan of the PC.  Tried to scan something from the screen of the printer touch but received the message "failed to scan. Try scanning from your PC. "Can anyone help?

  When you request support, please provide the HP model name and/or product the full number of the computer in question.

  Assuming that your new Envy23 AIO TouchSmart computer running 64-bit Windows 8 operating system, you can find the driver recommended for your Photosmart B109n-z HERE. If you are running another operating system, the driver can be chosen amongst the Photosmart B109n - the driver software download page &.

  Please send Bravo

• HP Envy 100 - impossible to activate the scan from the printer

  I use an iMac end of 2012 and spin the Mavericks. Envy is connected to my WiFi.

  I was never able to get the urge to turn on a scan from the printer. When I press on the analysis on the printer, I get 3 options and choose 'computer '. I can get some information from introduction to scanning the computer. He says this analysis for computer is activated automatically when the printer is first set up and I need to have installed the HP printing software. This means to me that something has not been properly Setup and I can't work it out. I just updated my software as a result of Mavericks. I regularly print to the printer and am able to activate a scan of my computer.

  I read a few posts on the software uninstallation. If necessary, I don't know what needs to be uninstalled and reinstalled and how I could do that.

  Can anyone help?

  Thank you

  HI - my apologies for the slow response.

  Would it not possible to check to see if "Scan to Computer" is enabled in the utility application from HP?  This application must be in the folder Applications/Hewlett-Packard.

  Once the application opens, you may need to select your device if it is not already selected.  The configuration option "Scan to Computer" should appear at the bottom of the document window (see attachment "Utility HP - selected ENVY").

  Try to open the "Scan to Computer" configuration item and display settings.  Please refer to attachments "utility HP - Scan to computer do not activated" and "Utility HP - compatible computer Scan" for what that might look like if the feature is enabled or disabled.

  Let me know what you see.

  Also - since your connection to the printer on a wireless network, have you tried to move the printer closer to the router or wireless access point wireless?  I'm curious to know if there may be some intermittent network connectivity that is to interrupt the function computer scanning.  I would try to move the printer right next to the wireless router access point / wireless to see if that helps the issue.

  I will continue to work on this issue for you to get the help you need.

• Scan from the printer to the pc wireless

  I have officejet pro 8600, it allows to scan to my pc, but I change to a new room and changed the password and now it will print and scan from my pc, but not the printer to the pc, I set myself until I have change the pass with the switch, but now who would not work and now I can't even come... Help please!

  Hello @kimsgirll1999,

  By the sounds of your post, it only appears that all background programs running on your Windows 7 computer is originally interference when trying to scan to your HP Officejet Pro 8600 e-all-in-one printer. Before the reactivation of these background programs can I please have you try the following steps.

  Enable the computer analysis:

  1. click on the HP Printer Wizard on your computer desktop icon:

  

  2. click on Actions of the Scanner, then Manage scanning to computer.

  3. click on Activate to activate the scan function. If the scan function is already enabled, click disable, and then click Activate again.

  4. on the printer control panel, press Scan (), support on computerand then tap the name of the computer that is displayed.

  If the scan of the computer working now, please activate your start-up services through the 'step 5: reactivate MSCONFIGthe steps I described in my post above.

  Once Msconfig services are activated, try to scan from the front panel of your printer to see if your computer is always present.

  Please let me know if this procedure works for you. Good luck!

• Scan from the printer HP for MacBook

  After the Update September 1, 2016 at the HP6500A, the scan from the printer to the computer software has become inoperative.  Printer cannot detect the MacBook Pro.  Can you help me?

  You might have better luck using the image transfer application on the pre installed in your folder scanner Applications.

  Help here > the basics of the Mac: using a scanner - Apple Support

• Start scanning from the computer?

  I have a hp photosmart C5550, when I try to scan to start the scan of the computer says, how can I do?

  Antal Hello

  That article and the instructions are for a different printer and software. You should see 'Manage Scan to Computer' under the 'Actions of Scaner. If you get an error or messages let me know. I noticed you did another post where you mention Windows 7 which is your operating system?

  How to scan from my computer. How can I activate my HP 3050 scanner? Windows 7

  

• I can scan from the printer wireless on my I Pad

  I have a printer of HP Deskjet 3050 a all-in-one wireless and I would like to scan on my I Pad 2?

  Hello

  You can scan from your iPad via the wireless network using the HP Printer Control application:

  https://iTunes.Apple.com/us/app/HP-printer-control/id469284907?Mt=8

  The application is available for download from the App Store, be sure to search iPhone apps as the application compatible with the iPad, but isn't an application native iPad.

  Shlomi

• HP3070 b611all in a printer: HP3070 unable to scan from the printer control panel

  Hello

  Although I can scan a document from my laptop I can't do it from the printer control panel.

  I tried following the instructions in the Support Center
  "HP Deskjet 3070 e - all-in - One Printer Series - how Scan: from the control panel" but I didn't know where I could: ' activate the scan to the computer connection (Windows only).

  Anywhere there is no mention of "Scan" under settings B3070 only in a separate file, HP Scan on my system...

  Thanks for your help so far.  I now have much more HP files/programs that I started with.  What can delete and to be able to continue to print wireless & scan of the computer, or maybe I should ask what files do I need and I can uninstall.

  I ordered the following cable to establish a connection between my laptop and a printer?  I hope it is the right one.

  USB printer cable lead for HP Hewlett Packard and Lexmark A - B

• scanning from hpOfficejet Pro 8610 for OSX ELCapitan

  I can't scan from my Officejet Pro 8610 All-in-one scanner my computer Mac (OSX El Capitan).  It prints well ok.  Someone can help me.  Thank you.

  Hi @Ellen6,

  Thanks for joining the Forums of HP Support for a solution to your problem of scanning.

  I understand that you can print fine on your computer Mac OS X 10.11 El Capitan for a HP Officejet Pro 8610 e-all-in-one printer, but you are unable to scan. I would like to help with that.

  I would like to start by resetting printing Mac system. If you are unsure how, here is an Apple Support document that can help - reset the printing system.

  After resetting the printing system, the printer will have to be added to the printers and Scanners window. You want to make sure that you select the driver "HP OfficeJet Pro 8610 series" instead of the driver "AirPrint" in the menu in the window of printer "Add" drop-down 'use'. Here is a document that can help with this if needed - Add or remove a printer.

  Please let me know if that solves the problem, or if you need assistance.

• can not scan from printer to computer Windows 8.1

  scan from the printer to the computer not windows 8.1

  Hi @skinz

  Thank you for letting me know what HP printer you have.  I'll guess that you receive an error message about a connection error when scanning.

  I've included the document a "Computer no. has detected" or "connection error" message when scanning for HP Officejet 6600 e-all-in-one and 6700 Premium e-All-in-One Printer Series (H711) .  Please click on your operating system and follow the troubleshooting steps.

  Please let me know the results.

• scanning from my pc

  How can I find the screen to scan from my printer hp 5510d series pc, I'm confused... I can't remember where the controls are on the pc...

  Hello

  For Windows, you can click HP 5510 icon on the desktop, and you can see this option in the menu.

  Kind regards.