SD card reader is identified as a WPD file system Volume driver and can not read SD cards.

Similar Questions

• WPD file system volume driver, card reader, code 10

  Used to have a Vista system to windows 7 update on top and the card reader has worked without any problems, in fact a full install of windows 7, the card reader appears four times (once for each location in the card reader) 'device cant start code 10' 'WPD file system volume driver. " If for example, I put a Memory stick card in the slot, he then shows up in my computer as a drive can be used to read and write from.

  The external USB card reader that I keep with my camera also has the same problem. This works perfectly on XP and Vista on this PC, the internal card reader used to be in this PC also worked great on XP and Vista as well as Windows 7 which has been installed on top of Vista.

  I checked for new drivers for the new card reader, are none for Windows 7, so there should not be any question here.

  Looks like I solved, went into computer management, the Manager disk and found that they were not in fact assigned to the card reader drive letters. Seed it when the media was designed, windows a drive letter assigned automatically, once the media was ejected from the letter assigned was swept away, this caused the WPD 10 error, so I manually set a drive letter for each location on the card reader all errors are now gone.

• (Code 31) "" device is the ' WPD file system Volume driver "-Windows cannot load the drivers"

  original title: in (under portable devices) Device Manager I get the following message. _ "the device is not working properly because Windows could not load the drivers required for this device. (Code 31) "" responding device is the "WPD file system Volume driver" _

  The Windows Event Viewer reports-

  Information - drivers have been installed successfully for device - driver Installation
  Information - it was not possible to access the device () after installing the drivers.
  Error code 0 x 80070651 - migration pilot

  I finally solved the above as follows;

  a reinstall the drivers of my motherboard chipset

  b, restart the PC

  c will unistalling and then remote control panel/system/Device Manager device possible (it is not possible to remove all)

  d PC restart and all devices removed in step C reinstall themselves automatically - restart the PC once the process is complete and the problem is solved

  PS the problem the appliance was a USB2 memory card reader

  Hope this works for you

• WPD file system Volume driver does not (code 10)

  My card reader has been giving this error in the Manager of devices for a few weeks, I reinstalled Window 7 Pro x 64. He has never had this error previously with Windows 7 Pro x 64 and the card reader didn't come with all the drivers of its own. There is an exclamation mark next to 4 devices in Device Manager marked as "WPD file system Volume driver" in the category of portable devices. There is also an entry under drive for these 4 devices called readers:

  IN - WIN CF Card USB Device, IN - WIN MS Card USB Device, SD Card USB Device IN - WIN SM Card USB Device IN - WIN

  I tried a drive letter to each of the 4 devices allocation but the drive letter will stick only if there is a device inserted into the appropriate slot and the drive letter is removed when I remove the memory card.

  Any help would be greatly appreciated as this is driving me crazy.

  p.s. I just tried the Microsoft Fix It utility, but even if she found the error and reinstalled the driver 4 times (once for each error), it has not solved the problem. Perhaps there is a updated driver somewhere?

  Hi Bendigo,

  As you have tried all the steps, you can try the steps and check mentioned below.

  This problem may be caused by corrupted files of INF. To resolve this issue, try to copy these files from a known 64-bit Windows 7 computer.

  a. try to copy usbstor.inf and usbstor. PNF (c:\windows\inf) from another known computer 64-bit Windows 7 to the problem computer. (You can also download them from another computer on your email and download them on computer problem)

  b. restart the computer check, if it is detected and works very well.

  See the Microsoft article below:

  Description of errors related to the 10 Code that generates the Device Manager in Windows on computers

  http://support.Microsoft.com/kb/943104/

  Hope this information is useful.

  Jeremy K
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• WPD file system Volume driver

  Every time my computer starts a window indicates that the WPD file system volume driver should be updated. I'm updating, but it continues to offer whenever I start my computer. How to stop and what is WPD?

  Hello

  Please read this thread:
  http://social.technet.Microsoft.com/forums/en/itprovistahardware/thread/afa881a1-1216-4c88-a1d8-f9add1827dc5 Good luck, Rick Rogers, aka "Crazy" - Microsoft MVP http://mvp.support.microsoft.com Windows help - www.rickrogers.org

• Download pdf files open in wordpad and can not be read

  After downloading some files open in wordpad and they cannot be read.they appear as a sort of code.this that happens with both text and photo files.i can't find another application to try to open them in.

  Hello

  WordPad can't open PDFs correctly, you need a pdf reader, and the most popular is Adobe reader. Please download it from the following link and install it on your computer:

  http://get.Adobe.com/reader/

  (Please check snap).

  8.1 Windows comes with a drive, but it is not good enough.

  Kind regards.

• Windows WPD - access denied file system Volume driver

  original title: Driver Windows WPD files Volume

  I just installed the Service Pack 2 of Vista for 64-bit system.  Now, I have a message looking for driver for my printer.  When I search for it, I get the message

  Refusal of access Windos WPD files Volume driver

  I just installed the Service Pack 2 of Vista for 64-bit system.  Now, I have a message looking for driver for my printer.  When I search for it, I get the message

  Refusal of access Windos WPD files Volume driver

  Support FREE from Microsoft for SP2:

  https://support.Microsoft.com/OAS/default.aspx?PRID=13014&Gprid=582034&St=1

  Free unlimited installation and compatibility support is available for Windows Vista, but only for Service Pack 2 (SP2). This support for SP2 is valid until August 30, 2010.

  Microsoft free support for Vista SP2 at the link above.

  See you soon.

  Mick Murphy - Microsoft partner

• I have a MS streets and trips 2010 and can not send cards to other owners of MS Streets and Trips

  I have a MS streets and trips 2010 and can not send cards to other owners of MS Streets and Trips

  ,

  Check with the streets and the support of the TRIPS Agreement and its forums.

  Streets & Trips
  http://www.Microsoft.com/streets/en-us/default.aspx

  Streets & Trips - help and Support
  http://www.Microsoft.com/streets/en-us/support-and-training.aspx

  Streets and travel community
  http://www.Microsoft.com/streets/en-us/community-and-news.aspx

  Streets and travel Forum
  http://social.Microsoft.com/forums/en-us/streetsandtrips/threads

  Support for MapPoint, streets & trips and Highway
  http://support.Microsoft.com/ph/851

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• RAID 5 volume is corrupted, RAW and not NTFS file systems shows now Windows can't read the Volume.

  RAID 5 volume is corrupted, files systems shows RAW and not NTFS now, Windows cannot read Volume, how do I convert to NTFS without losing data on the Volume. Raid 5 has been created by the Raid software

  Hello

  Your question is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please post your question in the Technet Forum. You can follow the link to your question:

  http://social.technet.Microsoft.com/forums/en-us/category/w7itpro

  Hope this information helps.

• I am running windows vista on the PC of my church and have inserted a USB stick with a MP4 file on it, but I can not read this file.

  I am running windows vista on the PC of my church and have inserted a USB stick with a MP4 file on it, but I can not read this file. Can I get help?

  I created a video for our Church on a desktop of Windows 7 through Pinnacle Studio 14 (editor) and registered as a .mp4 file. I then put it on a flash drive and put the flash drive in the computer of the Church, that is running Windows Vista, and the file will not play. Please provide help quickly!

  -Corey

  You need a media player that is compatible with .mp4 files.

  The following preferential ticket should solve your dilemma.

  (FWIW... it's always a good idea to create a system)
  Restore point before installing software or updates)

  VLC Media Player
  http://www.filehippo.com/download_vlc/
  (works on XP/Vista/7)

• Accidentally, I saved a PDF file in the cloud and can't be deleted from there. Help, please. I've upgraded to Adobe Acrobat Reader DC and it does not allow me to save the scans on my computer.

  Accidentally, I saved a PDF file in the cloud and can't be deleted from there. Help, please. I've upgraded to Adobe Acrobat Reader DC and it does not allow me to save the scans on my computer.

  Or simply open CD player

  Go to the Home tab then Document Cloud

  Click on the PDF file to be removed

  Click on remove in the top

• I have adobe reader xi and can not find the "create button" in order to combine several files into a single pdf

  I have adobe reader xi and can not find the "create button" in order to combine several files into a single pdf

  Hello

  Reader is software to view PDF' only.

  You must either a pack PDF to perform the function of thin or Acrobat.

  Reader is not the software to perform editing functions.

  Concerning

  Sukrit diallo

• scratch the numbers on the card and can not read what do I do?

  I've wiped off the map of the SPINDLE too hard and can't read the last few numbers do - what I do?

  I guess that's the PIN to upgrade at any time?

  My PIN code does not work, what should I do?

  If your PIN does not work, try the following:

  1. check that the PIN has been entered correctly. PIN code is not case sensitive and is alpha-numeric.

  2. make sure that the PIN has not already been used to obtain a product key. A PIN can be used only once to get a product key. If the PIN has been used, you can connect to your account with your Windows Live ID (if you have it when the PIN has been entered) to access your product key or you can check your email for the confirmation e-mail, that you have received when the PIN has been consumed to access your product key.

  https://Windows.getmicrosoftkey.com/support-home.aspx

  Who should I contact if I have problems installing and / or activation of my product key card?

  Please contact customer service at the:

  https://Windows.getmicrosoftkey.com/support-home.aspx

• I have a disc in my Mac and can not understand about where to go read the content?

  I have a disc in my desktop iMac computer and can't figure out how to break through the buttons right or my computer to read the content of the program?

  Double-click the icon of the disk on the desktop. I hope that you have installed an application that can read the content for you.

  If you don't see the icon of the disk on the desktop, open the Finder, then go to the Finder menu bar and click Finder > Preferences, and then select the general tab and then make sure: CD, DVD and iPods is selected.

• Help? the source volume is read-write and can not be disassembled...

  I use 10.11.5 on an iMac 21.5 ", end of 2009 and I want to restore the OS X 10.11.5 to HD on an external drive but I get this message" Source volume is read = write and cannot be disassembled, so it cannot be copied from block. "  I can find answers do not address El Capitan.  Help would be greatly appreciated.

  .. .Goldie

  You use disk utility's restore feature?

  If the HD has a recovery partition, you can make starting in place of the recovery.

  Or you can use SuperDuper! (the basic version is free and can copy the entire disk, the paid version allows "smart updates", which copies only files that are different, saving time) running on externally to perform the copy.