SE DHCPNACK to the IP on another router

Similar Questions

• The VPN Clients need access to the subnet on another router

  Hello

  We have a pix 515e PIX Version 8.0 (2)

  We have two subnet 10.1.x.x/16 and 10.2.x.x/16

  The firewall is on 10.1.x.x and vpn clients can access this subnet.

  The firewall can ping 10.2.x.y where x is a server in the other subnet.

  On the 10.2.x.x customers out the firewall.

  The problem is that vpn clients cannot access the server of 10.2.x.y even if the pix can ping 10.2.x.y and the road for him.

  What I need to check that the vpn rules are correct in the pix 515e?

  I think it is a rule of exemption nat or something like that not exactly sure.

  Everything would be a great help.

  Thank you

  Hello

  For clients VPN access to these subnets, check the following:

  1 NAT exemption include these subnets (if not using NAT)... it's the NAT0 ACL command

  2. these subnets is included in the split tunneling

  3. these subnets have a route to the PIX to send traffic to the VPN client pool.

  4. There are no ACLs not applied to the inside interface of the PIX deny this communication.

  Federico.

• Connect to Airport Extreme to another router

  Hello.  I searched this forum to see if my question is already answered.  I couldn't find all the signs that answer.  If it has already been answered, please point me to the subject.  Otherwise, here's my question:

  I need to expand Internet coverage in my house.  This is the configuration I want to implement:

  • Cable modem (at one end of my house) connected to a WiFi router non - Apple.

  • Use an Ethernet cable to the router through my attic, at one Airport Extreme to the other end of the House

  • I would like to run an Ethernet cable from the Airport Extreme to my TV and another cable to an AppleTV

  This would give wireless coverage to the entire House and Internet wired for television and the AppleTV.

  I would like some advice on how best to implement.  Here are a few questions (although I don't know if I ask to everything that I need to ask):

  • If the Airport Extreme be configured with DHCP or a static IP address?

  • If the Airport Extreme and the other router have the same SSID and password?  Or it doesn't matter?

  • What should I do a configuration to make the Ethernet connection work seamlessly in Airport Extreme to the other router on the cable modem?

  • I guess I can configure the other router (connected to the cable modem) to DHCP.  Is this correct?

  Thanks in advance for any advice.  If all goes well, I plan to spend this Saturday morning crawling into the attic and tonight Saturday benefiting the whole Internet.

  Should the Airport Extreme be configured with DHCP or a static IP address?

  DHCP, unless you have a preference for a static IP address.

  Airport Extreme and the other router has the same SSID and password?

  Yes, if you want both of your routers to behave as if they provided a unique network of "big". No, if you want to require users to log on the wireless provided separately by each router.

  I have to do any configuration to make the Ethernet connection work seamlessly in Airport Extreme to the other router on the cable modem?

  Just run configuration 'Wizard' of Apple, and it will assign the correct parameters to the AirPort Extreme.

  I guess I can configure the other router (connected to the cable modem) to DHCP.  Is this correct?

  It is not clear, given that we do not know what another router you may have. Do you mean that the other router connected to the modem via DHCP... or... you hear the other router provide DHCP and NAT services for the entire network?

• Apple Extreme, Time Capsule and Express on the same system, what is the best way to set it up so that all devices smoothly from one end of the House to another?

  Apple Extreme, Time Capsule and Express on the same system, what is the best way to set it up so that all devices smoothly from one end of the House to another?

  I'm going to assume that you plan to have wireless devices.

  Let's say that the Capsule is your "main" router  If this is the case, then it must be located in the House, so that the distance between the time Capsule is the same for the outside walls of the House.

  Then, on the 'left' side of the House, looking for an airport to midway between the Capsule and time of the outer wall of the House. Do the same thing the 'right' side of the House.

  In other words, each of the two airports that "extend" the wireless signal are located at equal distance from the Capsule of time... but they are in opposite ends of the House.

  If you intend to interconnect all the airports and Time Capsule using a permanent, Ethernet wired... which by far is the 'best' way to put in place a network in terms of performance and reliability... then you can locate one of the devices anywhere you want.

• How can I find out the password for my router, I missed place

  I want to add another computer to use though, I can't find the password for my router.  Is it possible to find it on one of my other computers.

  Except if you have really tightened down on the security of your router, adding another computer should be a simple to plug it.  In any case, most routers can be reset by default (including the password) by pressing the button of reset for about 10 seconds.  As you do not have the brand or the model of router in your post, all I can recommend is for more specific information, you should go to your router manufacturer's website and download the manual for your make and model of router and follow the instructions.

  HTH,
  JW

• After the death of firewall router in an outtage power yesterday I replaced my router have restored internet access, but none of my corporate office offices can access our network printer/scanner.

  yerterday morning, that we had a power outage at my place of business. When power has been restored we can't access internet from any one of our desktop computers. After working with a material MFG co troubleshotter. our firewall router NETGEAR, it has been determined that the equipment was defective. They offered to replace the camera for only the shipping charges, I felt an acceptable solution. Then I was told that with bureaucracy, it would take two weeks to get the new unit. Well, my choice was then to set for two weeks and slowly go out of business or buying a new router. I have relpaced the unit with another mod. Netgear router and this quickly got back up again, at least if we could access our system of internal accounting and the internet. My problem is as it is now that I can't access our office network printer.scanner (kyoceraMita) of any one of my desktops. At this point, I'd appreciate any help. I own my business, but am not a computer guy of any measurment known to man. I have this idea, maybe it's a simple software for all fit everyone access to what they need, but I don't know what it is maybe. If sufficient information, in my view, that I could probably fix the problem myself without providing any benefits of outdoor programming.

  The problem now is that the router has changed, the addresses IP, subnet mask, default gateway address, network security wireless network wireless security password and other settings no longer correspond to the original router.  As you said that the SCP can all see each other, you need to see Kyocera and network user's guide 'unit' in order to find the IP address, subnet mask and other network setting the configuration parameters 'method '.

• Cascading Linksys router to another router (LAN LAN)

  My current set is the asame LAN - LAN as in this link... http://KB.Linksys.com/Linksys/GetArticle.aspx?docid=785463d9ecaf4cac84aed245b08d615f_3733.XML

  my 'main' router is defined as DHCP server only, and wireless is disabled on it. This router is in the basement.

  my "secondary" router is in the living room... The DHCP service is disabled on this router and this provided routers beams for the House at 2.4 and 5 Ghz wireless... allows to call "Network 2" SSID 2,4 and 5 what we call "Netowrk 5".  Wireless coverage is really good in the whole of the House except basement. I would like to do better in the basement as well.

  In this current set up what could I do to make it better. As the "primary" router isn't beaming wireless I might add another router 'third '?

  Any help would be appreciated.

  Thank you

  He should choose the height of the 2.4 GHz SSID or the SSID 5 GHz, but only in the case were two router have the same SSID for the 2.4 Ghz and the same SSID for 5 Ghz. (Remember separated SSID at 2.4 Ghz and 5 Ghz signals)

  It can be confusing, so here's an example:

  Main router:

  2.4 Ghz SSID: myhouse

  5 GHz SSID: myhouse_5gz

  Linksys router:

  2.4 Ghz SSID: myhouse

  5 GHz SSID: myhouse_5gz

  When a wireless client moves around the place he will switch to signal the harder for SSID it finally connected to.

• I can mutually ping in router RVS4000 VLAN without another router

  One of our clients has RVS400 router with 4-port LAN VIRTUAL. We have recently added Crestron devices to our network and have some network problem. Search Google points to this page: Network slow question as discessed in this article: Troubleshooting network slow issues... There are two things happening with the Crestron system:... www.chicagotech.net/NetForums/viewtopic.php?f=1&t=7737 It recommends to create a local network VIRTUAL for Crestron. However, the Cisco RVS400 manual States: "function VLANS at layer 2.» VLANS isolate traffic within the VIRTUAL LAN, router layer 3 functioning router is needed to allow traffic between the VLANS. Layer 3 routers identify segments and coordinate with local networks virtual. "If we create two VLANS on the router without another router, can access us each other in these two VLAN?

  Hi chicagotech.

  I implemented a RVS4000 in our laboratory and created 2 VLAN, VLAN 1 and VLAN 2. I connected two PCs, 1 on each VLAN and they were able to ping each other with Inter-VLAN routing active. Here are the steps I followed:

  1. Go to L2 Switch-> create a VLAN. I have added VLAN ID: 2 and click Add VLAN
  2. Go to membership to a VLAN and select VLAN 2 from the drop-down. In the table for Port 2, select the Untagged radio button and click on save at the bottom.
  3. Go to settings-> Advanced Routing and ensure that the Inter-VLAN routing is enabled. (It is enabled by default)
  4. Connect a PC to port 2 and make sure he gets an IP to VLAN 2. (in this case 192.168.2.100) Ping this address in VLAN 1 PC-> success. From VLAN 2 PC, ping 192.168.1.101 (VLAN 1 PC)-> success.
  5. As a test I gave then the PCs in each VLAN to an IP address static and turned off the DHCP server on the router. 192.168.1.102 was able to ping 192.168.2.102 and vice versa.
  6. I then disabled Inter-VLAN routing and the PC could ping is no longer among them. They still had full access to the internet.

  It seems that the devices connected to the RVS4000 in different VLANS have no trouble to access each other with Inter-VLAN routing active.

• hit the tab opens another line of address rather than go to the subject field

  With the last update to Thunderbird, I can not tab directly from the field address within the scope of the topic. Hit the tab opens another line of address to be removed, then tab will move to the scope of the topic. I hope someone solves this problem quickly.

  In my version 31.2.0
  It depends on how MANY fields are automatically inserted.

  So if I have 3 set as default, but have used an email address, tab scrolls the (two) other TO and in THE fields and then go to topic.

  The rest to THE fields may not necessarily appear if the content by separating the divider was raised to provide more space to strike. So it might appear as though the creation of a new FIELD (which is normally when you press the enter/return key), but it's actually only to already available in THE fields.

  To check this:
  Open a new message of Scripture.
  Lower the separator bar to reveal header space, all the fields to display and also a few extra empty lines.
  How many auto fields appear?

  Place the cursor at the top of the page to and use Tab to move.
  the move of the tab should move from FIELD to the fall of choice FOR down, then next field. When the last FIELD was used, tab should go to the question, it should not go to an empty field AND create a new FIELD.

• New RSS downloaded all the messages, BUT 'To' watch as the author of another blog in my stream.

  I added a new blog to my 'articles & News Feeds', the first since the update, I added to 24.6.0. 6 posts on the blog completely downloaded, but when I looked at the contents of the folder, the column 'From' a was filled with the name of another blogger in my stream. The two articles are blogger, if that makes a difference. Of course, this isn't a major problem, but it is an annoyance.

  My guess is that the blog uses a common e-mail address. So, delete the entry in your address book for the person who is not displayed.

• You need to reset and or change my old icloud account of moms on the phone with another. When I try to reset it with the information that we know that it says "blocked account"

  You need to reset and or change my old iCloud account of moms on the phone with another. When I try to reset it with the information that we know that it says "blocked account"

  ACCOUNT SAFETY CONTACT NUMBERS

• How can I use highlighting conditional to assign a cell using the value of another cell

  I would use conditional highlighting on a cell based on the value of another cell.

  For example:

  If K2 is 1, then I would than A4 Green

  Any suggestions?

  Hi louis,.

  This approach is to add a cell to compare your target for:

  

  Highlight the rule in this case:

  

  Quinn

• I have different bookmarks I want to keep on each computer, synchronization will delete the bookmarks on a single computer and replace the bookmarks from another computer in their place

  I have not yet used sync, but I sense it's going to be a problem if I do. I have different bookmarks I want to keep it on each computer. Sync will delete the bookmarks on a single computer and replace the bookmarks from another computer in their place? So I think that will erase the bookmarks on the second computer you configured to synchronize. Is there a way to merge bookmarks on every computer in the library of a bookmark that contains all bookmarks on both computers, so I'm not all bookmarks in sync?

  Just to be clear, this is something that we have commented several times in the forum, Firefox Sync adds everything that is already in the device for the account and pushes this info for the rest of the devices.

  So if you have 2 computers with data X and the other with the data from there, once you set up synchronization in both computers you will have X + Y at the same time.

  I hope that clarifies the doubts...

• Before loading the site asked, another site is loaded all the ads have installed malware stuff but do not stop it

  When I entered a Web site, in particular of Google, before my shipment of the requested site, another site is loaded - one for the advertising of other websites, etc. In order to get to that I entered, I come back (with the help of the arrow of the Web site), and then really hit enter on my keyboard. I thought it was some sort of Mal-ware, but who have cleaned, but he always does this - it's driving me crazy!

  Make a check of malware with some scan of malware programs. You need to scan with all programs, because each program detects a different malicious program. Make sure that you update each program to get the latest version of the database prior to scanning.

  • http://www.malwarebytes.org/mbam.php - Malwarebytes' Anti-Malware
  • http://www.superantispyware.com/ - SuperAntispyware
  • http://www.microsoft.com/windows/products/winfamily/defender/default.mspx - Windows Defender: Home Page
  • http://www.safer-networking.org/en/index.html - Spybot Search & Destroy
  • http://www.lavasoft.com/products/ad_aware_free.php - Ad-Aware Free

  See also 'Spyware on Windows': http://kb.mozillazine.org/Popups_not_blocked and searches are redirected to another site

• Satellite A100-549: BSOD after I used the recovery from another PC

  Hello.

  Had a few probs with my laptop and decided to recover it using another pc recovery disc.
  I get the laptop is a Toshiba a100-549. Unfortunately for some reason I can't disks that were originally with her.

  The opertaing system is Windows xp. The disks I got with a Vista.
  It loads OK but goes to a blue screen after 30 seconds and restarts. Is there a reason for this and can I do.

  I think I may need to get your hands on a good drive and load it on again.
  Someone at - it copies of drives for this laptop and able to send me their. I'll gladly pay for them...

  Colin

  Hello

  Don t user recovery drive to another PC, because it won't work.
  You can use a clean Windows OS disk or the Toshiba recovery disc.

  Why? Because the recovery disk contains an image. The image is a package containing a Windows OS, drivers and other software.
  If you want to use the recovery from another PC disk then all the drivers, tools and software distributed for this PC will be loaded on your Toshiba laptop.
  This can cause the BSOD!

  So if you n t have the Toshiba recovery disc then you should use MS Windows CD!
  Toshiba drivers can be downloaded from the Toshiba page!