SE message which, due to the security I have to save the citrix .ica file to the location on the computer, and then double-click it to open.

Similar Questions

• Will not install driver installer of EPSON Scan (L210) - ' error occurred when installing re start the computer, and then try again.

  Original title: problem installing scanner

  EPSON Scan (L210) setup driver moved - "is an error occurred when installing re start the computer, and then try again.

  Hey there, MAHIPALSINGH143

  Welcome to the Microsoft community forums.

  So that the community help to install your printer, we will need more information. Please answer these questions:

  1. Windows what operating system are you running (Windows 10, 8.1, 7)?
  2. The troubleshooting steps have so you far?
  3. Did you upgrade to a new operating system?
     1. If Yes, what operating system you were on before?

  When you look at the error message, it doesn't look like you need to update your drivers. You will need to go on the official website of manufacturers, with your EPSON.

  Here is the site for the EPSON drivers: http://www.epson.co.uk/gb/en/viewcon/corporatesite/support

  When I entered your model of "Epson Scan (L210)" number, it does not recognize the product. Would you be able to check and make sure that you have provided the correct model number? Your model is a new printer?

  Kind regards

• Windows vista installation interrupted, click OK to restart the computer, and then restart the installation

  I was doing a reformat of the factory for windows vista on the laptop of my son (packard bell EasyNote LJ 65) when the battery is dead and the computer turned off. When I started it back up it gives the message: the computer restarted unexpectedly or encountered an unexpected error. Windows Setup cannot continue. To install Windows, click OK to restart the computer, and then restart the installation.
  Everything I try, I get no further than this message, I don't know where to go to continue the installation. The computer does not see that the installation was not completed. I tried to enter the menu with F9 where I had to do the reformatting of the factory of windows but it will not give me the option to continue installation, it shows just the vista Windows, but when I click brings back me to the error message
  Help, please!

  http://support.PackardBell.com/UK/

  For questions about the recovery process, contact the manufacturer of the computer.

  This isn't their recovery process, Microsoft.

  See you soon. Mick Murphy - Microsoft partner

• Error "Windows Setup cannot continue. To install windows, click ok to restart the computer, and then restart the installation. "When you try to install Windows.

  How can I configure my windows 7 after restoring my laptop to the factory conditians?

  My laptop had a blue screen and I couldn't get rid of it, I went into safe mode and restore my computer to factory conditions. When the computer says "the installation program starts services" you stop and I couldn't turn it back on for 15 minutes. When I turned on and tried to contained my setup, a message keeps poping up "the computer restarted unexpectedly or encountered an unexpected error." Windows Setup cannot continue. To install windows, click ok to restart the computer, and then restart the installation. "But no mader, how many times I reboot my laptop, the same message appears. What should I do? I've restored my computer several times and never had this problem.

  You should try another recovery.

  New computers coming often pre-installed with Windows 7 have what is called a recovery partition. This is used to reinstall an operating system in the case of a system failure. To access it, you need to start when you start your computer by pressing a function key. This can be either F1, F2, F9, F10, F11, F12 key DEL or tab. See the manual that came with your PC for instructions on how to reinstall Windows.

  If your recovery partition is not available or damaged, you must contact the manufacturer of your computer, and request that a defined recovery disk you can use to reinstall Windows 7. They could practice a small shipping and handling.

• I bought adobe photoshop elements13 & adobe first elments 13 and it keeps out error tells me to restart the computer, and then try to reinstall and it keeps it doing so. How to download or do I return to the store and make it

  I bought adobe photoshop elements13 & adobe first elments 13 and it keeps out error tells me to restart the computer, and then try to reinstall and it keeps it doing so. How to download or I have to take back to the store and ask them to help me.

  You try to download at the bottom of link?

  Download Photoshop Elements | 10, 11, 12, 13

  Or are you any error messages during launch or installation?  If so, post the exact error message.

• You can load the update of windows on the computer and then one more

  You can load the update of windows on the computer and then one more

  You can load Windows * updates on multiple computers. Should not be confused with * updates *. TaurArian [MVP] 2005-2010 - Update Services

• Is there a difference through the add printer from the Menu then simply open the print server in the Explorer, and then right-click on the printer you want, and then hit?

  Add a network printer (add printer vs right-click-> Connect)

  Hey just have a quick question that I can't find anywhere.

  To add network printers is there a difference through the add printer from the Menu then opening just the print server in the Explorer, and then right-click on the printer you want and pressing on connect?

  Hello Doughty08,

  No, there is no difference. Both methods will install the same printer available driver and the two will work the printer even.

• Driver EPSON Scan Setup installs - "error produced during installation to re start the computer, and then try again.

  New Epson Scanner GT - S50 Epson scan, set up driver will not install. keeps giving me "is an error occurred when installing re start the computer, and then try again" works fine on another pc with windows 7, but not from Dell. Tried to download from the website and cd. all other software is loading fine. Epson technical support cannot fix. Help!

  I finally had my Epson GT - S50 working. I have a contract with support iYogi.They tech were recommended by Dell.  It took them more than 12 hours to solve this problem. They had to do a full factory reset. I have had all my drives. The alleged problem with mine was HP. I have a hp all-in-one. It damaged my windows files. On re install, I had to install Epson scan first, this hp. I would not buy an epson again. The product works well now but still double flow a lot and is very picky. When it works well, it really accelerates my work verse scan with the Hp all-in-one. I'm really happy that I have a scanner, but wouldn't recommend an Epson.  I highly recommend I have Yogi tech support. They are worth every penny.

• Wireless network adapter does not work anymore and will not be repeated work without stopping the computer and then back on.

  Sometimes I leave my computer on at night.  Sometimes I notice that when I get back to him the next day that he has limited connection to the network I use.  When I try to disconnect it from the network, then reconnect, it says that it cannot connect.  Then, when I try to restart my computer it is sitting at a screen saying "stop down". "."  My wireless network software also is unaccessable in which she does not open and if I close the Task Manager and reopen it flashes for a second then closes.

  However when I turn it on manually and then turn it on again, which apparently is not good for the computer, I am once again able to connect to the network with full access.

  Can someone please tell me why this keeps happening and how to fix it?

  original title: unable to connect to a network.

  Hello

  Are you aware of any changes made to the computer, before the show?

  Method 1:

  Step 1: Safe Mode with networking

  Start your computer in safe mode with network and verify that the question.

  Start your computer in safe mode

  http://Windows.Microsoft.com/en-us/Windows7/start-your-computer-in-safe-mode

  Step 2: Clean boot

  If you are not facing the problem in safe mode with network, then put your computer in a clean boot and search for the issue.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  Note: once you are done with the boot, follow step 7 of article to put your computer to normal startup.

  Method 2:

  Update the NIC drivers and check the issue.

  Updated a hardware driver that is not working properly

  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

  Update drivers: recommended links

  http://Windows.Microsoft.com/en-us/Windows7/update-drivers-recommended-links

  Method 3:

  Run a virus scan and make sure.

  http://www.Microsoft.com/security/scanner/en-us/default.aspx

  Note: The Microsoft Safety Scanner ends 10 days after being downloaded. To restart a scan with the latest definitions of anti-malware, download and run the Microsoft Safety Scanner again.
   
  Important: While running scan on the hard drive if bad sectors are found on the hard drive when scanning try to repair this area if all available on which data may be lost.

  I hope this helps.

• I have a new windows 7 and it does not start? I went to the computer and then disk but usually do something?

  I bought a set of windows 7 from Tiger direct. It wont start too install? This PC has an adminastraitor and Im not she. The PC too was givin me an old PC

  Hi BruceVJ,

  It's sad to know that you are unable to install Windows 7 on the computer. I'll help you understand a fix for the problem. However, I need to ask you a few questions before proceeding.

  1. you try to upgrade an earlier version of Windows to Windows 7? If so, which version is installed on the computer?

  2. what happens when you try to install Windows 7?

  3. do you get the admin screen to ask password when you install Windows 7?

  Here are some links that should help you to work and solve the problem.

  Install, reinstall, or uninstall Windows

  http://Windows.Microsoft.com/en-us/Windows/help/install-reinstall-uninstall

  See also:

  Installation and reinstallation of Windows 7

  http://Windows.Microsoft.com/en-us/Windows7/installing-and-reinstalling-Windows-7

  Data loss caveat:

  Be sure to back up data that you want to keep before you begin. This is to ensure that there is no loss of data.

  Hope this information is helpful and let us know if you need more assistance. We will be happy to help.

• I don't and then double-click the title bar to reduce to a minimum the 21 FF

  I see that others have reported the problem, but there seems to be no response on the wire, can you help me?

  I have also this problem (Mac Firefox 21) but only if you are using a custom theme. When you use the appearance of Firefox by default, I can always double-click to minimize Firefox to the dock. I wonder if all the other people who have complained about this problem also used a custom theme?

• What material would keep ramdomly turn off the computer and then restarting him?

  OK, I completely re-charge this machine, but it still keeps randomly turn off and restart... someone has any suggestions other than "TRASH IT"?  I'm about to.  Can not get up-to-date, because of this random failure and reboot.  What do you think?  Please answer.  It is a bridge of 2002.  Thank you.

  David

  SWV

  "Southwest vidéo" wrote in the new message: * e-mail address is removed from the privacy... *

  OK, I completely re-charge this machine, but it still keeps randomly turn off and restart... someone has any suggestions other than "TRASH IT"?  I'm about to.  Can not get up-to-date, because of this random failure and reboot.  What do you think?  Please answer.  It is a bridge of 2002.  Thank you.

  David

  SWV

  Overheating is probably possible.  Check that the fan is working OK.  Also, make sure that the vents are not blocked. If they are blocked by the accumulation of dust, buy a can of compressed air in a computer store to blow off the dust, etc.

  In addition, make sure that the cards any plugin (video cards, etc.) are securely fixed in their media.

• I enter username and password to connect to a Web site, use the site, and then logoff. When I opened the site again, the username and password are alread filled in,

  The only way to prevent that I found so far is to close Firefox. When I opened to the top, go to the website, the user name and password are empty. It didn't happen with previous versions of Firefox.

  You can set the Boolean signon.autofillForms false pref on the topic: config page.

  • http://KB.mozillazine.org/signon.autofillForms
  • http://KB.mozillazine.org/about:config

  This can also be caused by cookies that are not removed correctly when you disconnected.

• I moved my files to another drive on my computer, and now if I try to open them, it says there is error: 1 and he said to uninstall and reinstall. How would I be able to reinstall the product?

  How can I reinstall my creative cloud? Is there another solution to the error: 1?

  Hi Max,.

  This article may help: https://helpx.adobe.com/creative-cloud/kb/failed-install-creative-cloud-desktop.html

  -Dave

• my cd/dvd is more listed on the computer and it will not play anything

  If I'm going to start the computer and then open cd/dvd is more listed also is absent from the menu equipment. I'm not a COMPUTER guru to take it easy with the answers. Thank you

  Hello

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and
  the correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
  devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">